- 28 Sep, 2020 21 commits
-
-
Thomas Pedersen authored
Recently channels gained a potential frequency offset, so include this in the per-channel survey info. Signed-off-by:
Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200922022818.15855-16-thomas@adapt-ip.com [add the offset only if non-zero] Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Thomas Pedersen authored
The changes required for associating in S1G are: - apply S1G BSS channel info before assoc - mark all S1G STAs as QoS STAs - include and parse AID request element - handle new Association Response format - don't fail assoc if supported rates element is missing Signed-off-by:
-
Thomas Pedersen authored
S1G beacons are 802.11 Extension Frames, so the fixed header part differs from regular beacons. Add a handler to process S1G beacons and abstract out the fetching of BSSID and element start locations in the beacon body handler. Signed-off-by:
-
Thomas Pedersen authored
minstrel_ht is confused by the lack of sband->bitrates, and S1G will likely require a unique RC algorithm, so avoid rate init for now if STA is on the S1G band. Signed-off-by:
-
Thomas Pedersen authored
S1G doesn't have legacy (sband->bitrates) rates, only MCS. For now, just send a frame at MCS 0 if a low rate is requested. Note we also redefine (since we're out of TX flags) TX_RC_VHT_MCS as TX_RC_S1G_MCS to indicate an S1G MCS. This is probably OK as VHT MCS is not valid on S1G band and vice versa. Signed-off-by:
-
Thomas Pedersen authored
For now just skip the duration calculation for frames transmitted on the S1G band and avoid a warning. Signed-off-by:
-
Thomas Pedersen authored
S1G allows listen interval up to 2^14 * 10000 beacon intervals. In order to do this listen interval needs a scaling factor applied to the lower 14 bits. Calculate this and properly encode the listen interval for S1G STAs. See IEEE802.11ah-2016 Table 9-44a for reference. Signed-off-by:
-
Thomas Pedersen authored
The sending STA type is implicit based on beacon or probe response content. If sending STA was an S1G STA, adjust the Information Element location accordingly. Signed-off-by:
-
Thomas Pedersen authored
This commit finds the correct offset for Information Elements in S1G beacon frames so they can be reported in scan results. Signed-off-by:
-
Thomas Pedersen authored
Extract the BSS primary channel from the S1G Operation element. Signed-off-by:
-
Thomas Pedersen authored
The S1G beacon is an extension frame as opposed to management frame for the regular beacon. This means we may have to occasionally cast the frame buffer to a different header type. Luckily this isn't too bad as scan results mostly only care about the IEs. Signed-off-by:
-
Thomas Pedersen authored
Include the S1G Capabilities element in an association request, and support the cfg80211 capability overrides. Signed-off-by:
-
Thomas Pedersen authored
NL80211_ATTR_S1G_CAPABILITY can be passed along with NL80211_ATTR_S1G_CAPABILITY_MASK to NL80211_CMD_ASSOCIATE to indicate S1G capabilities which should override the hardware capabilities in eg. the association request. Signed-off-by:
-
Thomas Pedersen authored
An S1G BSS can beacon at either 1 or 2 MHz and the channel width is unique to a given frequency. Ignore scan channel width for now and use the allowed channel width. Signed-off-by:
-
Thomas Pedersen authored
When deleting a channel context, mac80211 would assing NL80211_CHAN_WIDTH_20_NOHT as the default channel width. This is wrong in S1G however, so instead get the allowed channel width for a given channel. Fixes eg. configuring strange (20Mhz) width during a scan on the S1G band. Signed-off-by:
-
Johannes Berg authored
The vendor namespaces argument isn't described here, add it. Signed-off-by:
-
Johannes Berg authored
Two parameters are not described, add them. Signed-off-by:
-
Johannes Berg authored
There's a stray _ in the kernel doc, remove it. Signed-off-by:
-
Tova Mussai authored
Support 6 GHz scanning, by * a new scan flag to scan for colocated BSSes advertised by (and found) APs on 2.4 & 5 GHz * doing the necessary reduced neighbor report parsing for this, to find them * adding the ability to split the scan request in case the device by itself cannot support this. Also add some necessary bits in mac80211 to not break with these changes. Signed-off-by:
Tova Mussai <tova.mussai@intel.com> Signed-off-by:
-
Loic Poulain authored
Because we can miss AP wakeup (beacon) while scanning other channels, it's better go into wakeup state and inform the AP of that upon returning to the operating channel, rather than staying asleep and waiting for the next TIM indicating traffic for us. This saves precious time, especially when we only have 200ms inter- scan period for monitoring the active connection. Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Link: https://lore.kernel.org/r/1593420923-26668-1-git-send-email-loic.poulain@linaro.org [rewrite commit message a bit] Signed-off-by:
-
Florian Fainelli authored
After commit d0186842 ("net: vlan: Avoid using BUG() in vlan_proto_idx()"), vlan_proto_idx() was changed to return a signed integer, however one of its called: vlan_group_prealloc_vid() was still using an unsigned integer for its return value, fix that. Fixes: d0186842 ("net: vlan: Avoid using BUG() in vlan_proto_idx()") Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 27 Sep, 2020 19 commits
-
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Update for net-next. This patch series adds 2 main features to the bnxt_en driver: 200G link speed support and FEC support with some refactoring of the link speed logic. The firmware interface is updated to have proper support for these 2 features. The ethtool preset max channel value is also adjusted properly to account for XDP and TCs. ==================== Signed-off-by: -
Michael Chan authored
The current logic that calculates the preset maximum value for combined channel does not take into account the rings used for XDP and mqprio TCs. Each of these features will reduce the number of TX rings. Add the logic to divide the TX rings accordingly based on whether the device is currently in XDP mode and whether TCs are in use. Reviewed-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Michael Chan authored
This feature allows the user to set the different FEC modes on the NIC port. Any new setting will take effect immediately after a link toggle. Reviewed-by:
-
Michael Chan authored
The current code is reporting the FEC configured settings during link up. Change it to report the more useful active FEC encoding that may be negotiated or auto detected. Reviewed-by:
-
Michael Chan authored
Implement .get_fecparam() method to report the configured and active FEC settings. Also report the supported and advertised FEC settings to the .get_link_ksettings() method. Reviewed-by:
-
Edwin Peer authored
PORT_PHY_CONFIG is always sent with REQ_FLAGS_RESET_PHY set. This flag must be set in order for the firmware to institute the requested PHY change immediately, but it results in a link flap. This is unnecessary and results in an improved user experience if the PHY reconfiguration is avoided when the user requested speed does not constitute a change. Signed-off-by:
Edwin Peer <edwin.peer@broadcom.com> Signed-off-by:
-
Michael Chan authored
On some 200G dual port NICs, if one port is configured to 200G, firmware will disable the ethernet link on the other port. Firmware will send notification to the driver for the disabled port when this happens. Define a new field in the link_info structure to keep track of this state. The new phy_state field replaces the unused loop_back field. Log a message when the phy_state changes state. In the disabled state, disallow any PHY configurations on the disabled port as the firmware will fail all calls to configure the PHY in this state. Reviewed-by:
-
Edwin Peer authored
Add ethtool PAM4 link modes for: 50000baseCR_Full 100000baseCR2_Full 200000baseCR4_Full Signed-off-by: -
Edwin Peer authored
The firmware interface has added support for new link speeds using PAM4 modulation. Expand the bnxt_link_info structure to closely mirror the new firmware structures. Add logic to copy the PAM4 capabilities and settings from the firmware. Signed-off-by:
-
Edwin Peer authored
It will be necessary to update more than one field in the link_info structure when PAM4 speeds are added in a later patch. Instead of merely translating ethtool speed values to firmware speed values, change the responsiblity of this function to update all the necessary link_info fields required to force the speed change to the desired ethtool value. This also reduces code duplication somewhat at the two call sites, which otherwise both have to independently update link_info fields to turn off auto negotiation advertisements. Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen to have the same values, but req_link_speed is utilimately passed as force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of REQ_AUTO_LINK_SPEED. Reviewed-by:
Scott Branden <scott.branden@broadcom.com> Signed-off-by:
-
Edwin Peer authored
Extract the code for determining an advertised speed is no longer supported into a separate function. This will avoid some code duplication in a later patch when supporting PAM4 speeds, since these speeds are specified in a separate field. Reviewed-by:
-
Michael Chan authored
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG response size reduction, and a new counter added to ctx_hw_stats_ext struct to support the new 58818 chip. The ctx_hw_stats_ext structure is now the superset supporting the new 58818 chips and the prior P5 chips. Add a new flag to identify the new chip and use constants for the chip specific ring statistics sizes instead of the size of the structure. Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back to 96 bytes, the workaround added earlier to limit the size of this message for forwarding to the VF can be removed. Signed-off-by:
-
Yangbo Lu authored
Added the missing stub function for ptp_get_msgtype(). Fixes: 036c508b ("ptp: Add generic ptp message type function") Reported-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by:
-
Andrew Lunn authored
rivers/net/ethernet/marvell/mvpp2/mvpp2_main.c:7084:36: warning: ‘mvpp2_acpi_match’ defined but not used [-Wunused-const-variable=] 7084 | static const struct acpi_device_id mvpp2_acpi_match[] = { | ^~~~~~~~~~~~~~~~ Wrap the definition inside #ifdef/#endif. Compile tested only. Signed-off-by:Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Expose transceiver overheat counter Amit says: An overheated transceiver can be the root cause of various network problems such as link flapping. Counting the number of times a transceiver's temperature was higher than its configured threshold can therefore help in debugging such issues. This patch set exposes a transceiver overheat counter via ethtool. This is achieved by configuring the Spectrum ASIC to generate events whenever a transceiver is overheated. The temperature thresholds are queried from the transceiver (if available) and set to the default otherwise. Example: ... transceiver_overheat: 2 Patch set overview: Patches #1-#3 add required device registers Patches #4-#5 add required infrastructure in mlxsw to configure and count overheat events Patches #6-#9 gradually add support for the transceiver overheat counter Patch #10 exposes the transceiver overheat counter via ethtool ==================== Signed-off-by: -
Amit Cohen authored
Add structures for port statistics which read from core and not directly from registers. When netdev's ethtool statistics are queried, query the corresponding module's overheat counter from core and expose it as "transceiver_overheat". Signed-off-by:
Amit Cohen <amcohen@nvidia.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
-
Amit Cohen authored
Module temperature warning events are enabled for modules that have a temperature sensor and configured according to the temperature thresholds queried from the module. When a module is unplugged we are guaranteed not to get temperature warning events. However, when a module is plugged in we need to potentially update its current settings (i.e., event enablement and thresholds). Register to port module plug/unplug events and update module's settings upon plug in events. Signed-off-by:
-
Amit Cohen authored
The overheat counter is a per-module counter, but it is exposed as part of the corresponding netdev's statistics. It should therefore be presented to user space relative to the netdev's lifetime. Query the counter just before registering the netdev, so that the value exposed to user space will be relative to this initial value. Signed-off-by:
-
Amit Cohen authored
MTWE (Management Temperature Warning Event) is triggered for sensors whose temperature event enable bit is enabled in the MTMP register. Enable events for all the modules that have a temperature sensor. Signed-off-by:
-
