Merge branches 'for-2639/i2c-eg20t', 'for-2639/i2c-shmobile', 'for-2639/i2c-tegra' and 'for-2639/i2c-nomadik2' into for-linus/2640/i2c

This specifies the new per-platform timeout per I2C bus and
switches the I2C buses to fast mode, and increase the FIFO
depth to 8 for reads and writes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Reduce code size in the message transfer function by factoring out
a single-message transfer function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

In case of I2C timeout, reset the HW only after the HW status
is read, otherwise the staus will be lost.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The delay in the driver seems to be not needed, so remove it.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Markus Grape <markus.grape@stericsson.com>
Tested-by: Per Persson <per.xb.persson@stericsson.com>
Tested-by: Chethan Krishna N <chethan.krishna@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

1) Increase RX FIFO threshold so that there is a reduction in
the number of interrupts handled to complete a transaction.

2) Fill TX FIFO in the write function.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

It is seen that i2c-nomadik controller randomly stops generating the
interrupts leading to a i2c timeout. As a workaround to this problem,
add retries to the on going transfer on failure.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Use the pm_runtime API for pins control.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[deleted some surplus runtime PM code]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Modify the code to:
1)Print the cause of i2c failure only if the status is set to ABORT.
2)Print slave address on send/receive fail, will help in which slave
failed.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Correct the incorrect initialization of adapter timeout not to be
in milliseconds, as it needs to be done in jiffies.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The abort cause string itself is an error, so remove the redundant
explicit error message.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The code was returning bad error numbers or just -1 in some cases.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The I2C speed enumerators in the i2c-nomadik header file were in
the wrong order.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add option to have different i2c timeout delay for different i2c buses
specified in platform data. Default to the old value unless specified.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This on-chip I2C controller needs to fetch the regulator
representing its voltage domain so that it won't be switched off.
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
  sh: Ignore R_SH_NONE module relocations.
  SH: SE7751: Fix pcibios_map_platform_irq prototype.
  sh: remove warning and warning_symbol from struct stacktrace_ops
  sh: wire up sys_sendmmsg.
  clocksource: sh_tmu: Runtime PM support
  clocksource: sh_tmu: __clocksource_updatefreq_hz() update
  clocksource: sh_cmt: Runtime PM support
  clocksource: sh_cmt: __clocksource_updatefreq_hz() update
  dmaengine: shdma: synchronize RCU before freeing, simplify spinlock
  dmaengine: shdma: add runtime- and system-level power management
  dmaengine: shdma: fix locking
  sh: sh-sci: sh7377 and sh73a0 build fixes
  sh: cosmetic improvement: use an existing pointer
  serial: sh-sci: suspend/resume wakeup support V2
  serial: sh-sci: Runtime PM support
  sh: select IRQ_FORCED_THREADING.
  sh: intc: Set virtual IRQs as nothread.
  sh: fixup fpu.o compile order
  i2c: add a module alias to the sh-mobile driver
  ALSA: add a module alias to the FSI driver
  ...

Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools: Fix sample type size calculation in 32 bits archs
  profile: Use vzalloc() rather than vmalloc() & memset()

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (247 commits)
  [media] gspca - sunplus: Fix some warnings and simplify code
  [media] gspca: Fix some warnings tied to 'no debug'
  [media] gspca: Unset debug by default
  [media] gspca - cpia1: Remove a bad conditional compilation instruction
  [media] gspca - main: Remove USB traces
  [media] gspca - main: Version change to 2.13
  [media] gspca - stk014 / t613: Accept the index 0 in querymenu
  [media] gspca - kinect: Remove __devinitdata
  [media] gspca - cpia1: Fix some warnings
  [media] video/Kconfig: Fix mis-classified devices
  [media] support for medion dvb stick 1660:1921
  [media] tm6000: fix uninitialized field, change prink to dprintk
  [media] cx231xx: Add support for Iconbit U100
  [media] saa7134 add new TV cards
  [media] Use a more consistent value for RC repeat period
  [media] cx18: Move spinlock and vb_type initialisation into stream_init
  [media] tm6000: remove tm6010 sif audio start and stop
  [media] tm6000: remove unused exports
  [media] tm6000: add pts logging
  [media] tm6000: change from ioctl to unlocked_ioctl
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/hirofumi/fatfs-2.6:
  fat: Fix statfs->f_namelen
  fat: Replace all printk with fat_msg()
  fat: Add fat_msg() function for preformated FAT messages
  fat: Convert fat_fs_error to use %pV
  fat: Fix possible null deref in fat_cache_add()
  fat: use new setup() for ->dir_ops too

The coretemp driver provides a single set of device attributes for each
physical core of a HT CPU to avoid duplicate sensors.  This
functionality was introduced with commit d883b9f0 ("hwmon:
(coretemp) Skip duplicate CPU entries").

Commit e40cc4bd ("x86/hwmon: register alternate sibling upon CPU
removal") extends this functionality to register the HT sibling of a CPU
which is taken offline, to ensure that sensor attributes are provided if
at least one HT sibling of a core is online.

Add comments into the code describing the functionality in some more
detail.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We try to enforce it by using -Wstrict-prototypes, but apparently they
sometimes get through.  Introduced by 4eec42f3 ("watchdog: Change
the default timeout and configure nmi watchdog period based").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The shift used here to count the number of bits set in
the mask doesn't work above the low part for archs that
are not 64 bits.

Fix the constant used for the shift.

This fixes a 32-bit perf top failure reported by Eric Dumazet:

	Can't parse sample, err = -14
	Can't parse sample, err = -14
	...
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com
Link: http://lkml.kernel.org/r/1306200686-17317-1-git-send-email-fweisbec@gmail.comSigned-off-by: Ingo Molnar <mingo@elte.hu>

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
  PCI: Don't use dmi_name_in_vendors in quirk
  PCI: remove unused AER functions
  PCI/sysfs: move bus cpuaffinity to class dev_attrs
  PCI: add rescan to /sys/.../pci_bus/.../
  PCI: update bridge resources to get more big ranges when allocating space (again)
  KVM: Use pci_store/load_saved_state() around VM device usage
  PCI: Add interfaces to store and load the device saved state
  PCI: Track the size of each saved capability data area
  PCI/e1000e: Add and use pci_disable_link_state_locked()
  x86/PCI: derive pcibios_last_bus from ACPI MCFG
  PCI: add latency tolerance reporting enable/disable support
  PCI: add OBFF enable/disable support
  PCI: add ID-based ordering enable/disable support
  PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
  PCI: Set PCIE maxpayload for card during hotplug insertion
  PCI/ACPI: Report _OSC control mask returned on failure to get control
  x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
  PCI: handle positive error codes
  PCI: check pci_vpd_pci22_wait() return
  PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
  ...

Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be
moved the intel SMBUS ID definitons to the i2c-i801.c driver.

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: obey minleft values during extent allocation correctly
  xfs: reset buffer pointers before freeing them
  xfs: avoid getting stuck during async inode flushes
  xfs: fix xfs_itruncate_start tracing
  xfs: fix duplicate workqueue initialisation
  xfs: kill off xfs_printk()
  xfs: fix race condition in AIL push trigger
  xfs: make AIL target updates and compares 32bit safe.
  xfs: always push the AIL to the target
  xfs: exit AIL push work correctly when AIL is empty
  xfs: ensure reclaim cursor is reset correctly at end of AG
  xfs: add an x86 compat handler for XFS_IOC_ZERO_RANGE
  xfs: fix compiler warning in xfs_trace.h
  xfs: cleanup duplicate initializations
  xfs: reduce the number of pagb_lock roundtrips in xfs_alloc_clear_busy
  xfs: exact busy extent tracking
  xfs: do not immediately reuse busy extent ranges
  xfs: optimize AGFL refills

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
  ARM: bcmring: convert to use sp804 clockevents
  ARM: bcmring: convert to sp804 clocksource
  ARM: 6912/1: bcmring: Add clkdev table in init_early
  clockevents: ARM sp804: obtain sp804 timer rate via clks
  clockevents: ARM sp804: allow clockevent name to be specified
  clocksource: ARM sp804: obtain sp804 timer rate via clks
  clocksource: ARM sp804: allow clocksource name to be specified
  clocksource: convert OMAP1 to 32-bit down counting clocksource
  clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
  clocksource: convert SPEAr platforms 16-bit up counting clocksource
  clocksource: convert Integrator/AP 16-bit down counting clocksource
  clocksource: convert W90x900 24-bit down counting clocksource
  clocksource: convert ARM 32-bit down counting clocksources
  clocksource: convert ARM 32-bit up counting clocksources
  clocksource: add common mmio clocksource
  ARM: update sa1100 to reflect PXA updates
  ARM: omap1: convert to using readl/writel instead of volatile struct
  ARM: omap1: delete useless interrupt handler
  ARM: s5p: consolidate selection of timer register
  ARM: 6939/1: fix missing 'cpu_relax()' declaration
  ...

Fixed the broken links in the SubmittingPatches file.

[ The old links turn out to not be broken after all, but the new links
  are certainly more readable - Linus ]
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixed typos.

v2: Incorporated changes by Randy Dunlap.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Update LXR (Linux cross reference) web link.
Signed-off-by: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

max_user_instances was removed in this commit:

   commit 9df04e1f
   Author: Davide Libenzi <davidel@xmailserver.org>
   Date:   Thu Jan 29 14:25:26 2009 -0800

    epoll: drop max_user_instances and rely only on max_user_watches

but the documentation entry was not removed.

Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Lucian Adrian Grijincu <lucian.grijincu@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

v2, updated based on comments from Joe and Paul.

Update to Documentation/dontdiff, based on many updates to
various .gitignore patches over the last 2 years.

Initially begun by Michael Prokop <mika@grml.org>, with lots of
changes by Randy Dunlap.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Michael Prokop <mika@grml.org>
Cc: Joe Perches <joe@perches.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, apic: Include module.h header in apic_flat_64.c
  x86, apic: Make apic drivers static
  x86, apic: Clean up bigsmp apic selection code
  x86, apic: Use .apicdrivers section for the apic drivers list
  x86, apic: Introduce .apicdrivers section to find the list of apic drivers
  x86, x2apic: Move the common bits to x2apic.h
  x86, x2apic: Minimize IPI register writes using cluster groups
  x86, x2apic: Track the x2apic cluster sibling map
  x86, x2apic: Remove duplicate code for IPI mask routines
  x86, apic: Use probe routines to simplify apic selection
  x86, ioapic: Consolidate mp_ioapic_routing[] into 'struct ioapic'
  x86, ioapic: Consolidate gsi routing info into 'struct ioapic'
  x86, ioapic: Consolidate mp_ioapics[] into 'struct ioapic'
  x86, ioapic: Consolidate ioapic_saved_data[] into 'struct ioapic'
  x86, ioapic: Add struct ioapic
  x86, ioapic: Remove duplicate code for saving/restoring RTEs
  x86, ioapic: Use ioapic_saved_data while enabling intr-remapping
  x86, ioapic: Allocate ioapic_saved_data early
  x86, ioapic: Fix potential resume deadlock

Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Increase SCHED_LOAD_SCALE resolution
  sched: Introduce SCHED_POWER_SCALE to scale cpu_power calculations
  sched: Cleanup set_load_weight()

* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (970 commits)
  staging: usbip: replace usbip_u{dbg,err,info} and printk with dev_ and pr_
  staging:iio: Trivial kconfig reorganization and uniformity improvements.
  staging:iio:documenation partial update.
  staging:iio: use pollfunc allocation helpers in remaining drivers.
  staging:iio:max1363 misc cleanups and use of for_each_bit_set to simplify event code spitting out.
  staging:iio: implement an iio_info structure to take some of the constant elements out of iio_dev.
  staging:iio:meter:ade7758: Use private data space from iio_allocate_device
  staging:iio:accel:lis3l02dq make write_reg_8 take value not a pointer to value.
  staging:iio: ring core cleanups + check if read_last available in lis3l02dq
  staging:iio:core cleanup: squash tiny wrappers and use dev_set_name to handle creation of event interface name.
  staging:iio: poll func allocation clean up.
  staging:iio:ad7780 trivial unused header cleanup.
  staging:iio:adc: AD7780: Use private data space from iio_allocate_device + trivial fixes
  staging:iio:adc:AD7780: Convert to new channel registration method
  staging:iio:adc: AD7606: Drop dev_data in favour of iio_priv()
  staging:iio:adc: AD7606: Consitently use indio_dev
  staging:iio: Rip out helper for software rings.
  staging:iio:adc:AD7298: Use private data space from iio_allocate_device
  staging:iio: rationalization of different buffer implementation hooks.
  staging:iio:imu:adis16400 avoid allocating rx, tx, and state separately from iio_dev.
  ...

Fix up trivial conflicts in
 - drivers/staging/intel_sst/intelmid.c: patches applied in both branches
 - drivers/staging/rt2860/common/cmm_data_{pci,usb}.c: removed vs spelling
 - drivers/staging/usbip/vhci_sysfs.c: trivial header file inclusion

* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
  USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
  USB: UHCI: Support big endian GRUSBHC HC
  sparc: add {read,write}*_be routines
  USB: UHCI: Add support for big endian descriptors
  USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
  USB: UHCI: Add support for big endian mmio
  usb-storage: Correct adjust_quirks to include latest flags
  usb/isp1760: Fix possible unlink problems
  usb/isp1760: Move function isp1760_endpoint_disable() within file.
  USB: remove remaining usages of hcd->state from usbcore and fix regression
  usb: musb: ux500: add configuration and build options for ux500 dma
  usb: musb: ux500: add dma glue layer for ux500
  usb: musb: ux500: add dma name for ux500
  usb: musb: ux500: add ux500 specific code for gadget side
  usb: musb: fix compile error
  usb-storage: fix up the unusual_realtek device list
  USB: gadget: f_audio: Fix invalid dereference of initdata
  EHCI: don't rescan interrupt QHs needlessly
  OHCI: fix regression caused by nVidia shutdown workaround
  USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
  ...

apic_flat_64.c needs to include module.h because it uses
EXPORT_SYMBOL_GPL().

This fixes these warnings on some !SMP randconfigs:

  arch/x86/kernel/apic/apic_flat_64.c:31: warning: data definition has no type or storage class
  arch/x86/kernel/apic/apic_flat_64.c:31: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
  arch/x86/kernel/apic/apic_flat_64.c:31: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20110523104300.dd532a99.randy.dunlap@oracle.comSigned-off-by: Ingo Molnar <mingo@elte.hu>

* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (48 commits)
  serial: 8250_pci: add support for Cronyx Omega PCI multiserial board.
  tty/serial: Fix break handling for PORT_TEGRA
  tty/serial: Add explicit PORT_TEGRA type
  n_tracerouter and n_tracesink ldisc additions.
  Intel PTI implementaiton of MIPI 1149.7.
  Kernel documentation for the PTI feature.
  export kernel call get_task_comm().
  tty: Remove to support serial for S5P6442
  pch_phub: Support new device ML7223
  8250_pci: Add support for the Digi/IBM PCIe 2-port Adapter
  ASoC: Update cx20442 for TTY API change
  pch_uart: Support new device ML7223 IOH
  parport: Use request_muxed_region for IT87 probe and lock
  tty/serial: add support for Xilinx PS UART
  n_gsm: Use print_hex_dump_bytes
  drivers/tty/moxa.c: Put correct tty value
  TTY: tty_io, annotate locking functions
  TTY: serial_core, remove superfluous set_task_state
  TTY: serial_core, remove invalid test
  Char: moxa, fix locking in moxa_write
  ...

Fix up trivial conflicts in drivers/bluetooth/hci_ldisc.c and
drivers/tty/serial/Makefile.

I did the hci_ldisc thing as an evil merge, cleaning things up.

cpu_sibling_mask() is not defined unless CONFIG_SMP is defined, so it
must not be used directly in the code without ifdef protection.

To solve the problem and avoid ifdefs in the code, define
for_each_sibling() and use it instead.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  hrtimers: Reorder clock bases
  hrtimers: Avoid touching inactive timer bases
  hrtimers: Make struct hrtimer_cpu_base layout less stupid
  timerfd: Manage cancelable timers in timerfd
  clockevents: Move C3 stop test outside lock
  alarmtimer: Drop device refcount after rtc_open()
  alarmtimer: Check return value of class_find_device()
  timerfd: Allow timers to be cancelled when clock was set
  hrtimers: Prepare for cancel on clock was set timers

Conflicts:
	arch/arm/Kconfig
	arch/arm/mach-ns9xxx/include/mach/uncompress.h

Merge branches 'consolidate', 'ep93xx', 'fixes', 'misc', 'mmci', 'remove' and 'spear' into for-linus