- 02 Mar, 2010 34 commits
-
-
H Hartley Sweeten authored
Use resource_size(). Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Acked-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Anton Vorontsov authored
EHCI FSL controller preserve its state during sleep mode, so nothing fancy needs to be done. Though, during 'deep sleep' mode (as found in MPC831x CPUs) the controller turns off and needs to be reinitialized upon resume. This patch adds support for hibernation and resuming after deep sleep. Based on Dave Liu and Jerry Huang's work[1]. [1] http://www.bitshrine.org/gpp/linux-fsl-2.6.24.3-MPC8315ERDB-usb-power-mangement.patchSigned-off-by:
Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by:
-
Anton Vorontsov authored
This patch fixes following warnings: ehci-fsl.c:43:5: warning: symbol 'usb_hcd_fsl_probe' was not declared. Should it be static? ehci-fsl.c:150:6: warning: symbol 'usb_hcd_fsl_remove' was not declared. Should it be static? Signed-off-by:
-
Dmitri Epshtein authored
This patch fix audio record functionality for some Full speed sound blaster devices. Issue: Sometimes transaction complete indication is coming from HW one frame later. Solution: If scan_periodic process now frame or previous frame now-1 and sitd transaction is not finished yet, exit scan_periodic function and check the same transaction in the next frame. Signed-off-by:
Dimitry Epshtein <dima@marvell.com> Signed-off-by:
Saeed Bishara <saeed@marvell.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Dmitri Epshtein authored
Sometimes disable_periodic() stop scan_periodic before than free_cached_itd_list() was called. In such case USB Host stacked during disconnect operation Solution: add call of free_cached_itd_list() function in disable_periodic() Signed-off-by:
-
Sarah Sharp authored
Add a new host controller driver method, reset_device(), that the USB core will use to notify the host of a successful device reset. The call may fail due to out-of-memory errors; attempt the port reset sequence again if that happens. Update hub_port_init() to allow resetting a configured device. Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Sarah Sharp authored
When a USB device is reset, the xHCI hardware must know, in order to match the device state and disable all endpoints except control endpoint 0. Issue a Reset Device command after a USB device is successfully reset. Wait on the command to finish, and then cache or free the disabled endpoint rings. There are four different USB device states that the xHCI hardware tracks: - disabled/enabled - device connection has just been detected, - default - the device has been reset and has an address of 0, - addressed - the device has a non-zero address but no configuration has been set, - configured - a set configuration succeeded. The USB core may issue a port reset when a device is in any state, but the Reset Device command will fail for a 0.96 xHC if the device is not in the addressed or configured state. Don't consider this failure as an error, but don't free any endpoint rings if this command fails. A storage driver may request that the USB device be reset during error handling, so use GPF_NOIO instead of GPF_KERNEL while allocating memory for the Reset Device command. Signed-off-by:
-
Sarah Sharp authored
Add the hub emulation code to allow ports on an xHCI root hub to be disabled. Add the code to clear the port enabled/disabled bit, and clear the port enabled/disabled change bit. Like EHCI, the port cannot be enabled by setting the port enabled/disabled bit. Instead, a port is enabled by the host controller after a reset. Signed-off-by:
-
Sarah Sharp authored
Refactor the code to clear the port change bits in the port status register. All port status change bits are write one to clear. Remove a redundant port status read that was supposed to unblock any posted writes. We read the port after the write to get the updated status for debugging, so the port read after that is unnecessary. Signed-off-by:
-
Sarah Sharp authored
All commands that can be issued to the xHCI hardware can come back with vendor-specific "informational" completion codes. These are to be treated like a successful completion code. Refactor out the code to test for the range of these codes and print debugging messages. Signed-off-by:
-
Sarah Sharp authored
The xhci_command structure is the basic structure for issuing commands to the xHCI hardware. It contains a struct completion (so that the issuing function can wait on the command), command status, and a input context that is used to pass information to the hardware. Not all commands need the input context, so make it optional to allocate. Allow xhci_free_container_ctx() to be passed a NULL input context, to make freeing the xhci_command structure simple. Signed-off-by:
-
Sarah Sharp authored
Refactor out the code to cache or free endpoint rings from recently dropped or disabled endpoints. This code will be used by a new function to reset a device and disable all endpoints except control endpoint 0. Signed-off-by:
-
Sarah Sharp authored
If we fail to queue an evaluate context command or a configure endpoint command to the command ring in xhci_configure_endpoint(), we need to remove the xhci_command structure from the device's command list before returning. If the command is left on the command list, it will sit there indefinitely, blocking commands submitted after this fails. Signed-off-by:
-
Alan Stern authored
This patch (as1316) adds some error checking to usb_submit_urb(). It's conditional on CONFIG_USB_DEBUG, so it won't affect normal users. The new check makes sure that the actual type of the endpoint described by urb->pipe agrees with the type encoded in the pipe value. The USB error code documentation is updated to include the code returned by the new check, and the usbfs SUBMITURB handler is updated to use the correct pipe type when legacy user code tries to submit a bulk transfer to an interrupt endpoint. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Francesco Lavra authored
Add reset resume logic to the cdc acm driver Signed-off-by:
Francesco Lavra <francescolavra@interfree.it> Acked-by:
Oliver Neukum <oliver@neukum.org> Signed-off-by:
-
Pete Zaitcev authored
My distro kernel (Fedora Rawhide) started throwing warnings from DMA API checker, so I have no choice but band-aid it quick. There's no attempt to reuse DMA buffers. Control messages are only sent rarely anyway. Signed-off-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Enrico Scholz authored
hardware reports wrong interrupt. Although such a situation should not happen, the compiler complains about this access. This patch adds a sanity check and generates warning to detect such issues. Signed-off-by:
Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Acked-by:
-
Valentin Longchamp authored
On various mxc boards, the intial ULPI reads resulted in a timeout which prevented the transceiver to be identified and thus the ehci device to be probed. Initializing the hardware lines connected to the transceiver (through pdata->init call) before actually enabling clocks and configuring registers in the devices fixes this problem. Signed-off-by:
Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by:
-
Mark Adamson authored
Removed CS5 and CS6 from data bits since these are not supported in FTDI hardware. Signed-off-by:
Mark J. Adamson <mark.adamson@ftdichip.com> Signed-off-by:
-
Johan Hovold authored
Latency timeout was read but never stored on port probe. When ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0 rather than the default 16ms. Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Johan Hovold authored
Fixes confusing "serial_chars_in_buffer = port 0" messages. Signed-off-by:
-
Johan Hovold authored
We always push characters to ldisc immediately regardless of ASYNC_LOW_LATENCY. Signed-off-by:
-
Johan Hovold authored
Resubmitting read urb fails with -EPERM if completion handler runs while urb is being killed on close. This should not be reported as an error. Signed-off-by:
-
Simon Arlott authored
Changes: Return an empty string for modulation when there is no connection Fix sysfs unload race conditions Log firmware load process, remove delay Add new configuration interface Remove cxacru-cf.bin Signed-off-by:Simon Arlott <simon@fire.lp0.eu> Signed-off-by:
-
Simon Arlott authored
This has never worked properly because wsize passed to cxacru_cm() is incorrectly set to the number of values instead of the data bytes. The maximum number of values that can be set at once is 7 which means the device will not get enough data to work with and none of the configuration values will be used. At least one existing cxacru-cf.bin file contains invalid data which will prevent the modem from syncing properly. Fixing it is likely to break existing systems, and the new sysfs interface for setting configuration parameters can provide the same functionality. A script is provided to convert from the original format. Signed-off-by:
-
Simon Arlott authored
The modem can be configured using CM_REQUEST_CARD_DATA_SET, although CM_REQUEST_CARD_DATA_GET does not return any data. Tested by setting the modulation (0x0a) option. There is a list of parameters in the following archive, but the meaning of many of them is not well documented: http://sourceforge.net/project/shownotes.php?release_id=301825 This source also indicates that the highest parameter set is 0x4a but this varies by model so an arbitrary limit of 0x7f has been used (the index is a 32-bit integer). Signed-off-by:
-
Simon Arlott authored
Firmware writing takes 256ms per 4KB with OHCI, which is very slow compared to 7ms per 4KB with UHCI. Until I have access to a hardware USB analyser it may not be possible to determine why this happens. Instead of appearing to do nothing, log progress when writing firmware and then log the ATM device information when finished. Remove an unnecessary 4 second delay. Signed-off-by:
-
Simon Arlott authored
These commands were found by accident... fortunately it still works even if the flash memory is erased, despite having no USB device IDs. Some example sysfs code for raw command access: http://simon.arlott.org/pub/cxacru/raw.cSigned-off-by:
-
Simon Arlott authored
It is possible for usb_get_intfdata() to return NULL if sysfs is accessed while the module is being unloaded or the device is being removed. Move the access code to an inline function in usbatm.h, and return -ENODEV if any of the pointers are NULL. It should not be possible for the instance data or atm device to be invalid until after unbind() completes and the sysfs attributes have been removed. Signed-off-by:
-
Simon Arlott authored
When attempting to read data that is not actually an array of values, the length may be negative which causes an Oops due to a likely access off the end of the data array. This bug should not occur under normal use unless the device returns an invalid response. Signed-off-by:
-
Simon Arlott authored
When there is no connection, return an empty string instead of "0" for the connection modulation. Signed-off-by:
-
Martin Fuzzey authored
Signed-off-by:
Martin Fuzzey <mfuzzey@gmail.com> Signed-off-by:
-
Martin Fuzzey authored
Also fixes tab/space issue causing checkpatch to complain. Signed-off-by:
-
Martin Fuzzey authored
This driver is a Full / Low speed only USB host for the i.MX21. Signed-off-by:
-
- 01 Mar, 2010 6 commits
-
-
Linus Torvalds authored
Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci * 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits) DaVinci DM365: Adding support for SPI EEPROM DaVinci DM365: Adding DM365 SPI support DaVinci DM355: Modifications to DM355 SPI support DaVinci: SPI: Adding header file for SPI support. davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table() DaVinci: DM365: Voice codec support for the DM365 SoC davinci: clock: let clk->set_rate function sleep Add SDA and SCL pin numbers to i2c platform data davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138 davinci: build list of unused EDMA events dynamically davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case davinci: Keep count of channel controllers on a platform davinci: Correct return value of edma_alloc_channel api davinci: add CDCE949 support on DM6467 EVM davinci: add support for CDCE949 clock synthesizer davinci: da850/omap-l138 EVM: register for suspend support davinci: da850/omap-l138: add support for SoC suspend davinci: add power management support DaVinci: DM365: Changing default queue for DM365. ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-devLinus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits) sata_via: Delay on vt6420 when starting ATAPI DMA write ata: Detect Delkin Devices compact flash pata_efar: Enable parallel scanning pata_atiixp: enable parallel scan [libata] pata_atiixp: add locking for parallel scanning [libata] pata_efar: add locking for parallel scanning libata: Pass host flags into the pci helper [libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI libata: Allow pata_legacy to be built on non-ISA but PCI systems pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards [libata] pata_at91: fix backslash-continued string pata_via: store UDMA masks in via_isa_bridges table pata_via: fix address setup timings underlocking pata_serverworks: fix error message pata_serverworks: fix PIO setup for the second channel pata_efar: fix secondary port support pata_cypress: fix PIO timings underclocking pata_cs5535: use correct values for PIO1 and PIO2 data timings pata_cmd64x: remove unused definitions ...
-
Bart Hartgers authored
When writing a disc on certain lite-on dvd-writers (also rebadged as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends up in the datastream and on the disc, causing silent corruption. Delaying between sending the CDB and starting DMA seems to prevent this. I do not know if there are burners that do not suffer from this, but the patch should be safe for those as well. There are many reports of this issue, but AFAICT no solution was found before. For example: http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.htmlSigned-off-by:
Bart Hartgers <bart.hartgers@gmail.com> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com>
-
Ben Gardner authored
I have a Delkin Devices compact flash card that isn't being recognized using the SATA/PATA drivers. The card is recognized and works with the deprecated ATA drivers. The error I am seeing is: ata1.00: failed to IDENTIFY (device reports invalid type, err_mask=0x0) I tracked it down to ata_id_is_cfa() in include/linux/ata.h. The Delkin card has id[0] set to 0x844a and id[83] set to 0. This isn't what the kernel expects and is probably incorrect. The simplest work-around is to add a check for 0x844a to ata_id_is_cfa(). Signed-off-by:
Ben Gardner <gardner.ben@gmail.com> Signed-off-by:
-
Alan Cox authored
Again originally proposed by Bartlomiej but this does it by using the generic helper logic instead. Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Alan Cox authored
This was originally proposed by Bartlomiej but as a device specific expansion of the init_one function rather than making the helper more generic. Enable the parallel scan via the generic flags. Signed-off-by:
-
