commit 89e96ada upstream.

During testing pci root bus removal, found some root bus bridge is not freed.
If booting with pnpacpi=off, those hostbridge could be freed without problem.
It turns out that some devices reference are not released during acpi_pnp_match.
that match should not hold one device ref during every calling.
Add pu_device calling before returning.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2815ab92 upstream.

On Intel CPUs the processor typically uses the highest frequency
set by any logical CPU. When the system overheats
Linux first forces the frequency to the lowest available one
to lower the temperature.

However this was done only per logical CPU, which means all
logical CPUs in a package would need to go through this before
the frequency is actually lowered.

Worse this delay actually prevents real throttling, because
the real throttle code only proceeds when the lowest frequency
is already reached.

So when a throttle event happens force the lowest frequency
for all CPUs in the package where it happened. The per CPU
state is now kept per package, not per logical CPU. An alternative
would be to do it per cpufreq unit, but since we want to bring
down the temperature of the complete chip it's better
to do it for all.

In principle it may even make sense to do it for all CPUs,
but I kept it on the package for now.

With this change the frequency is actually lowered, which
in terms also allows real throttling to proceed.

I also removed an unnecessary per cpu variable initialization.

v2: Fix package mapping
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b54f47c8 upstream.

Using UBI on m25p80 can give messages like:

    UBI error: io_init: bad write buffer size 0 for 1 min. I/O unit

We need to initialize writebufsize; I think "page_size" is the correct
"bufsize", although I'm not sure. Comments?
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fcc44a07 upstream.

The writebufsize concept was introduce by commit
"0e4ca7e5 mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set writebufsize to 4 because this drivers writes at max 4 bytes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b6043874 upstream.

The writebufsize concept was introduce by commit
"0e4ca7e5 mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

However, we forgot to set this parameter for block2mtd. Set it to PAGE_SIZE
because this is actually the amount of data we write at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Joern Engel <joern@lazybastard.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c4cc625e upstream.

The writebufsize concept was introduce by commit
"0e4ca7e5 mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.

Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5289966e upstream.

This has been moved from .options to .bbt_options meanwhile. So, it
currently checks for something totally different (NAND_OWN_BUFFERS) and
decides according to that.

Artem Bityutskiy: the options were moved in
a40f7341 mtd: nand: consolidate redundant flash-based BBT flags

Artem Bityutskiy: CCing -stable
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bf011f2e upstream.

Since commit ca97dec2 the
command line parsing of MTD partitions does not work anymore.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a3c1e3b7 upstream.

In commit "c7975330 mtd: abstract last MTD partition parser argument" the
third argument of "mtd_device_parse_register()" changed from start address
of the MTD device to a pointer to a struct.

The "ixp4xx_flash_probe()" function was not converted properly, causing
an oops during boot.

This patch fixes the problem by filling the needed information into a
"struct mtd_part_parser_data" and passing it to
"mtd_device_parse_register()".
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e1660585 upstream.

Based on latest production information.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 464b57da ]

The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 78fb72f7 ]

Make CDC EEM recalculate the hard_mtu after adjusting the
hard_header_len.

Without this, usbnet adjusts the MTU down to 1494 bytes, and the host is
unable to receive standard 1500-byte frames from the device.

Tested with the Linux USB Ethernet gadget.

Cc: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 81213b5e ]

If both addresses equal, nothing needs to be done. If the device is down,
then we simply copy the new address to dev->dev_addr. If the device is up,
then we add another loopback device with the new address, and if that does
not fail, we remove the loopback device with the old address. And only
then, we update the dev->dev_addr.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2240eb4a ]

This patch corrects a bug in function sky2_open() of the Marvell Yukon 2 driver
in which the settings for PHY quick link are overwritten.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <shemminger@vyattta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 085f1afc ]

If port 0 of a 5717 serdes device powers down, it hides the phy from
port 1.  This patch works around the problem by keeping port 0's phy
powered up.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1d24fb36 ]

When K >= 0xFFFF0000, AND needs the two least significant bytes of K as
its operand, but EMIT2() gives it the least significant byte of K and
0x2. EMIT() should be used here to replace EMIT2().
Signed-off-by: Feiran Zhuang  <zhuangfeiran@ict.ac.cn>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c9651e70 upstream.

Since 3.2.12 and 3.3, some systems are failing to boot with a BUG_ON.
Some other systems using the pata_jmicron driver fail to boot because no
disks are detected.  Passing pcie_aspm=force on the kernel command line
works around it.

The cause: commit 4949be16 ("PCI: ignore pre-1.1 ASPM quirking when
ASPM is disabled") changed the behaviour of pcie_aspm_sanity_check() to
always return 0 if aspm is disabled, in order to avoid cases where we
changed ASPM state on pre-PCIe 1.1 devices.

This skipped the secondary function of pcie_aspm_sanity_check which was
to avoid us enabling ASPM on devices that had non-PCIe children, causing
trouble later on.  Move the aspm_disabled check so we continue to honour
that scenario.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=42979 and
          http://bugs.debian.org/665420

Reported-by: Romain Francoise <romain@orebokech.com> # kernel panic
Reported-by: Chris Holland <bandidoirlandes@gmail.com> # disk detection trouble
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Hatem Masmoudi <hatem.masmoudi@gmail.com> # Dell Latitude E5520
Tested-by: janek <jan0x6c@gmail.com> # pata_jmicron with JMB362/JMB363
[jn: with more symptoms in log message]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 49d4bcad upstream.

When DMA is enabled, sh-sci transfer begins with
 uart_start()
  sci_start_tx()
    if (cookie_tx < 0) schedule_work()
Then, starts DMA when wq scheduled, -- (A)
 process_one_work()
  work_fn_rx()
   cookie_tx = desc->submit_tx()
And finishes when DMA transfer ends, -- (B)
 sci_dma_tx_complete()
  async_tx_ack()
  cookie_tx = -EINVAL
  (possible another schedule_work())

This A to B sequence is not reentrant, since controlling variables
(for example, cookie_tx above) are not queues nor lists. So, they
must be invoked as A B A B..., otherwise results in kernel crash.

To ensure the sequence, sci_start_tx() seems to test if cookie_tx < 0
(represents "not used") to call schedule_work().
But cookie_tx will not be set (to a cookie, also means "used") until
in the middle of work queue scheduled function work_fn_tx().

This gap between the test and set allows the breakage of the sequence
under the very frequently call of uart_start().
Another gap between async_tx_ack() and another schedule_work() results
in the same issue, too.

This patch introduces a new condition "cookie_tx == 0" just to mark
it is "busy" and assign it within spin-locked region to fill the gaps.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6d8d1749 upstream.

There is no point in passing a zero length string here and quite a
few of that cache_parse() implementations will Oops if count is
zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4a649903 upstream.

Richard Weinberger noticed that on some RTC hardware that
doesn't support UIE mode, due to coarse granular alarms
(like 1minute resolution), the current virtualized RTC
support doesn't properly error out when UIE is enabled.

Instead the current code queues an alarm for the next second,
but it won't fire until up to a miniute later.

This patch provides a generic way to flag this sort of hardware
and fixes the issue on the mpc5121 where Richard noticed the
problem.
Reported-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1631fcea upstream.

<asm-generic/unistd.h> was set up to use sys_sendfile() for the 32-bit
compat API instead of sys_sendfile64(), but in fact the right thing to
do is to use sys_sendfile64() in all cases.  The 32-bit sendfile64() API
in glibc uses the sendfile64 syscall, so it has to be capable of doing
full 64-bit operations.  But the sys_sendfile() kernel implementation
has a MAX_NON_LFS test in it which explicitly limits the offset to 2^32.
So, we need to use the sys_sendfile64() implementation in the kernel
for this case.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8f0750f1 upstream.

These are used as offsets into an array of GDT_ENTRY_TLS_ENTRIES members
so GDT_ENTRY_TLS_ENTRIES is one past the end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://lkml.kernel.org/r/20120324075250.GA28258@elgon.mountainSigned-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 57779dc2 upstream.

While running the latest Linux as guest under VMware in highly
over-committed situations, we have seen cases when the refined TSC
algorithm fails to get a valid tsc_start value in
tsc_refine_calibration_work from multiple attempts. As a result the
kernel keeps on scheduling the tsc_irqwork task for later. Subsequently
after several attempts when it gets a valid start value it goes through
the refined calibration and either bails out or uses the new results.
Given that the kernel originally read the TSC frequency from the
platform, which is the best it can get, I don't think there is much
value in refining it.

So  for systems which get the TSC frequency from the platform we
should skip the refined tsc algorithm.

We can use the TSC_RELIABLE cpu cap flag to detect this, right now it is
set only on VMware and for Moorestown Penwell both of which have there
own TSC calibration methods.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
[jstultz: Reworked to simply not schedule the refining work,
rather then scheduling the work and bombing out later]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit de5b8e8e upstream.

If you try to set grace_period or timeout via a module parameter
to lockd, and do this on a big-endian machine where

   sizeof(int) != sizeof(unsigned long)

it won't work.  This number given will be effectively shifted right
by the difference in those two sizes.

So cast kp->arg properly to get correct result.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1265fd61 ]

We call the wrong replay notify function when we use ESN replay
handling. This leads to the fact that we don't send notifications
if we use ESN. Fix this by calling the registered callbacks instead
of xfrm_replay_notify().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5676cc7b ]

Some BIOS's don't setup power management correctly (what else is
new) and don't allow use of PCI Express power control. Add a special
exception module parameter to allow working around this issue.
Based on slightly different patch by Knut Petersen.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a6506e14 ]

no socket layer outputs a message for this error and neither should rds.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2a2a459e ]

napi->skb is allocated in napi_get_frags() using
netdev_alloc_skb_ip_align(), with a reserve of NET_SKB_PAD +
NET_IP_ALIGN bytes.

However, when such skb is recycled in napi_reuse_skb(), it ends with a
reserve of NET_IP_ALIGN which is suboptimal.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 94f826b8 ]

Commit f2c31e32 (net: fix NULL dereferences in check_peer_redir() )
added a regression in rt6_fill_node(), leading to rcu_read_lock()
imbalance.

Thats because NLA_PUT() can make a jump to nla_put_failure label.

Fix this by using nla_put()

Many thanks to Ben Greear for his help
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit dc72d99d ]

Matt Evans spotted that x86 bpf_jit was incorrectly handling negative
constant offsets in BPF_S_LDX_B_MSH instruction.

We need to abort JIT compilation like we do in common_load so that
filter uses the interpreter code and can call __load_pointer()

Reference: http://lists.openwall.net/netdev/2011/07/19/11

Thanks to Indan Zupancic to bring back this issue.
Reported-by: Matt Evans <matt@ozlabs.org>
Reported-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1f85851e ]

Since commit 299b0767(ipv6: Fix IPsec slowpath fragmentation problem)
In func ip6_append_data,after call skb_put(skb, fraglen + dst_exthdrlen)
the skb->len contains dst_exthdrlen,and we don't reduce dst_exthdrlen at last
This will make fraggap>0 in next "while cycle",and cause the size of skb incorrent

Fix this by reserve headroom for dst_exthdrlen.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit bbdb32cb ]

While testing L2TP functionality, I came across a bug in getsockname().  The
IP address returned within the pppol2tp_addr's addr memember was not being
set to the IP  address in use.  This bug is caused by using inet_sk() on the
wrong socket (the L2TP socket rather than the underlying UDP socket), and was
likely introduced during the addition of L2TPv3 support.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3fa016a0 upstream.

Looking at hibernate overwriting I though it looked like a cursor,
so I tracked down this missing piece to stop the cursor blink
timer. I've no idea if this is sufficient to fix the hibernate
problems people are seeing, but please test it.

Both radeon and nouveau have done this for a long time.

I've run this personally all night hib/resume cycles with no fails.
Reviewed-by: Keith Packard <keithp@keithp.com>
Reported-by: Petr Tesarik <kernel@tesarici.cz>
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reported-by: Lots of misc segfaults after hibernate across the world.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=37142Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: Bojan Smojver <bojan@rexursive.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fa0fb93f upstream.

For high-speed/super-speed isochronous endpoints, the bInterval
value is used as exponent, 2^(bInterval-1). Luckily we have
usb_fill_int_urb() function that handles it correctly. So we just
call this function to fill in the RX URB.

Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f946eeb9 upstream.

Module size was limited to 64MB, this was legacy limitation due to vmalloc()
which was removed a while ago.

Limiting module size to 64MB is both pointless and affects real world use
cases.

Cc: Tim Abbott <tim.abbott@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e59d27e0 upstream.

Firstly, task->tk_status will always return negative error values,
so the current tests for 'NFS4ERR_DELEG_REVOKED' etc. are all being
ignored.
Secondly, clean up the code so that we only need to test
task->tk_status once!
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 05e9cfb4 upstream.

We can currently loop forever in nfs4_lookup_root() and in
nfs41_proc_secinfo_no_name(), if the first iteration returns a
NFS4ERR_DELAY or something else that causes exception.retry to get
set.
Reported-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 66c4c35c upstream.

sysfs_slab_add() calls various sysfs functions that actually may
end up in userspace doing all sorts of things.

Release the slub_lock after adding the kmem_cache structure to the list.
At that point the address of the kmem_cache is not known so we are
guaranteed exlusive access to the following modifications to the
kmem_cache structure.

If the sysfs_slab_add fails then reacquire the slub_lock to
remove the kmem_cache structure from the list.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d97d32ed upstream.

When an IO error happens during inode deletion run from
xlog_recover_process_iunlinks() filesystem gets shutdown. Thus any subsequent
attempt to read buffers fails. Code in xlog_recover_process_iunlinks() does not
count with the fact that read of a buffer which was read a while ago can
really fail which results in the oops on
  agi = XFS_BUF_TO_AGI(agibp);

Fix the problem by cleaning up the buffer handling in
xlog_recover_process_iunlinks() as suggested by Dave Chinner. We release buffer
lock but keep buffer reference to AG buffer. That is enough for buffer to stay
pinned in memory and we don't have to call xfs_read_agi() all the time.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>