The current definition of the PCIe IO and MEM resources for SH7786
doesn't match what the datasheet says. For example, for PCIe0
0xfe100000 is advertised by the datasheet as a PCI IO region, while
0xfd000000 is advertised as a PCI MEM region. The code currently
inverts the two.

The SH4A_PCIEPARL and SH4A_PCIEPTCTLR registers allow to define the
base address and role of the different regions (including whether it's
a MEM or IO region). However, practical experience on a SH7786 shows
that if 0xfe100000 is used for LEL and 0xfd000000 for IO, a PCIe
device using two MEM BARs cannot be accessed at all. Simply using
0xfe100000 for IO and 0xfd000000 for MEM makes the PCIe device
accessible.

It is very likely that this was never seen because there are two other
PCI MEM region listed in the resources. However, for different
reasons, none of the two other MEM regions are usable on the specific
SH7786 platform the problem was encountered. Therefore, the last MEM
region at 0xfe100000 was used to place the BARs, making the device
non-functional.

This commit therefore adjusts those PCI MEM and IO resources
definitions so that they match what the datasheet says. They have only
been tested with PCIe 0.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>

Depending on the physical memory layout, some PCI MEM areas are not
usable. According to the SH7786 datasheet, the PCI MEM area from
1000_0000 to 13FF_FFFF is only usable if the physical memory layout
(in MMSELR) is 1, 2, 5 or 6. In all other configurations, this PCI MEM
area is not usable (because it overlaps with DRAM).

Therefore, this commit adjusts the PCI SH7786 initialization to mark
the relevant PCI resource as IORESOURCE_DISABLED if we can't use it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>

Some PCI MEM resources are marked as IORESOURCE_MEM_32BIT, which means
they are only usable when the SH core runs in 32-bit mode. In 29-bit
mode, such memory regions are not usable.

The existing code for SH7786 properly skips such regions when
configuring the PCIe controller registers. However, because such
regions are still described in the resource array, the
pcibios_scanbus() function in the SuperH pci.c will register them to
the PCI core. Due to this, the PCI core will allocate MEM areas from
this resource, and assign BARs pointing to this area, even though it's
unusable.

In order to prevent this from happening, we mark such regions as
IORESOURCE_DISABLED, which tells the SuperH pci.c pcibios_scanbus()
function to skip them.

Note that we separate marking the region as disabled from skipping it,
because other regions will be marked as disabled in follow-up patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>

In pcibios_scanbus(), we provide to the PCI core the usable MEM and IO
regions using pci_add_resource_offset(). We travel through all
resources available in the "struct pci_channel".

Also, in register_pci_controller(), we travel through all resources to
request them, making sure they don't conflict with already requested
resources.

However, some resources may be disabled, in which case they should not
be requested nor provided to the PCI core.

In the current situation, none of the resources are disabled. However,
follow-up patches in this series will make some resources disabled,
making this preliminary change necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>

Some devices may have a non-zero DMA offset, i.e an offset between the
DMA address and the physical address. Such an offset can be encoded
into the dma_pfn_offset field of "struct device", but the SuperH
implementation of the DMA mapping API does not observe this
information.

This commit fixes that by ensuring the DMA address is properly
calculated depending on this DMA offset.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>

The SH7786 has different physical memory layout configurations,
configurable through the MMSELR register. The configuration is
typically defined by the bootloader, so Linux generally doesn't care.

Except that depending on the configuration, some PCI MEM areas may or
may not be available. This commit adds a helper function that allows
to retrieve the current physical memory layout configuration. It will
be used in a following patch to exclude unusable PCI MEM areas during
the PCI initialization.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>

When responding to a debug trap (breakpoint) in userspace, the
kernel's trap handler raised SIGTRAP but returned from the trap via a
code path that ignored pending signals, resulting in an infinite loop
re-executing the trapping instruction.
Signed-off-by: Rich Felker <dalias@libc.org>

unflatten_device_tree() makes use of memblock allocation, and
therefore must be called before paging_init() migrates the memblock
allocation data to the bootmem framework. Otherwise the record of the
allocation for the expanded device tree will be lost, and will
eventually be clobbered when allocated for another use.
Signed-off-by: Rich Felker <dalias@libc.org>

Commit 00b73d8d ("sh: add working futex atomic ops on userspace
addresses for smp") changed the futex_atomic_op_inuser function to
use a loop. In case of the FUTEX_OP_SET op with a userspace address
containing a value different of 0, this loop is an endless loop.

Fix that by loading the value of oldval from the userspace before doing
the cmpxchg op, also for the FUTEX_OP_SET case.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Rich Felker <dalias@libc.org>

Pull perf fixes from Ingo Molnar:
 "Two fixlets"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/hwbp: Simplify the perf-hwbp code, fix documentation
  perf/x86/intel: Fix linear IP of PEBS real_ip on Haswell and later CPUs

Pull x86 fixes from Ingo Molnar:
 "Two UV platform fixes, and a kbuild fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/platform/UV: Fix critical UV MMR address error
  x86/platform/uv/BAU: Add APIC idt entry
  x86/purgatory: Avoid creating stray .<pid>.d files, remove -MD from KBUILD_CFLAGS

Pull x86 PTI fixes from Ingo Molnar:
 "Two fixes: a relatively simple objtool fix that makes Clang built
  kernels work with ORC debug info, plus an alternatives macro fix"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/alternatives: Fixup alternative_call_2
  objtool: Add Clang support

Merge tag 'kbuild-fixes-v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - fix missed rebuild of TRIM_UNUSED_KSYMS

 - fix rpm-pkg for GNU tar >= 1.29

 - include scripts/dtc/include-prefixes/* to kernel header deb-pkg

 - add -no-integrated-as option ealier to fix building with Clang

 - fix netfilter Makefile for parallel building

* tag 'kbuild-fixes-v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  netfilter: nf_nat_snmp_basic: add correct dependency to Makefile
  kbuild: rpm-pkg: Support GNU tar >= 1.29
  builddeb: Fix header package regarding dtc source links
  kbuild: set no-integrated-as before incl. arch Makefile
  kbuild: make scripts/adjust_autoksyms.sh robust against timestamp races

Pull networking fixes from David Miller:

 1) Fix RCU locking in xfrm_local_error(), from Taehee Yoo.

 2) Fix return value assignments and thus error checking in
    iwl_mvm_start_ap_ibss(), from Johannes Berg.

 3) Don't count header length twice in vti4, from Stefano Brivio.

 4) Fix deadlock in rt6_age_examine_exception, from Eric Dumazet.

 5) Fix out-of-bounds access in nf_sk_lookup_slow{v4,v6}() from Subash
    Abhinov.

 6) Check nladdr size in netlink_connect(), from Alexander Potapenko.

 7) VF representor SQ numbers are 32 not 16 bits, in mlx5 driver, from
    Or Gerlitz.

 8) Out of bounds read in skb_network_protocol(), from Eric Dumazet.

 9) r8169 driver sets driver data pointer after register_netdev() which
    is too late. Fix from Heiner Kallweit.

10) Fix memory leak in mlx4 driver, from Moshe Shemesh.

11) The multi-VLAN decap fix added a regression when dealing with device
    that lack a MAC header, such as tun. Fix from Toshiaki Makita.

12) Fix integer overflow in dynamic interrupt coalescing code. From Tal
    Gilboa.

13) Use after free in vrf code, from David Ahern.

14) IPV6 route leak between VRFs fix, also from David Ahern.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
  net: mvneta: fix enable of all initialized RXQs
  net/ipv6: Fix route leaking between VRFs
  vrf: Fix use after free and double free in vrf_finish_output
  ipv6: sr: fix seg6 encap performances with TSO enabled
  net/dim: Fix int overflow
  vlan: Fix vlan insertion for packets without ethernet header
  net: Fix untag for vlan packets without ethernet header
  atm: iphase: fix spelling mistake: "Receiverd" -> "Received"
  vhost: validate log when IOTLB is enabled
  qede: Do not drop rx-checksum invalidated packets.
  hv_netvsc: enable multicast if necessary
  ip_tunnel: Resolve ipsec merge conflict properly.
  lan78xx: Crash in lan78xx_writ_reg (Workqueue: events lan78xx_deferred_multicast_write)
  qede: Fix barrier usage after tx doorbell write.
  vhost: correctly remove wait queue during poll failure
  net/mlx4_core: Fix memory leak while delete slave's resources
  net/mlx4_en: Fix mixed PFC and Global pause user control requests
  net/smc: use announced length in sock_recvmsg()
  llc: properly handle dev_queue_xmit() return value
  strparser: Fix sign of err codes
  ...

In mvneta_port_up() we enable relevant RX and TX port queues by write
queues bit map to an appropriate register.

q_map must be ZERO in the beginning of this process.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Donald reported that IPv6 route leaking between VRFs is not working.
The root cause is the strict argument in the call to rt6_lookup when
validating the nexthop spec.

ip6_route_check_nh validates the gateway and device (if given) of a
route spec. It in turn could call rt6_lookup (e.g., lookup in a given
table did not succeed so it falls back to a full lookup) and if so
sets the strict argument to 1. That means if the egress device is given,
the route lookup needs to return a result with the same device. This
strict requirement does not work with VRFs (IPv4 or IPv6) because the
oif in the flow struct is overridden with the index of the VRF device
to trigger a match on the l3mdev rule and force the lookup to its table.

The right long term solution is to add an l3mdev index to the flow
struct such that the oif is not overridden. That solution will not
backport well, so this patch aims for a simpler solution to relax the
strict argument if the route spec device is an l3mdev slave. As done
in other places, use the FLOWI_FLAG_SKIP_NH_OIF to know that the
RT6_LOOKUP_F_IFACE flag needs to be removed.

Fixes: ca254490 ("net: Add VRF support to IPv6 stack")
Reported-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Miguel reported an skb use after free / double free in vrf_finish_output
when neigh_output returns an error. The vrf driver should return after
the call to neigh_output as it takes over the skb on error path as well.

Patch is a simplified version of Miguel's patch which was written for 4.9,
and updated to top of tree.

Fixes: 8f58336d ("net: Add ethernet header for pass through VRF device")
Signed-off-by: Miguel Fadon Perlines <mfadon@teldat.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enabling TSO can lead to abysmal performances when using seg6 in
encap mode, such as with the ixgbe driver. This patch adds a call to
iptunnel_handle_offloads() to remove the encapsulation bit if needed.

Before:
root@comp4-seg6bpf:~# iperf3 -c fc00::55
Connecting to host fc00::55, port 5201
[  4] local fc45::4 port 36592 connected to fc00::55 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.00   sec   196 KBytes  1.60 Mbits/sec   47   6.66 KBytes
[  4]   1.00-2.00   sec   304 KBytes  2.49 Mbits/sec  100   5.33 KBytes
[  4]   2.00-3.00   sec   284 KBytes  2.32 Mbits/sec   92   5.33 KBytes

After:
root@comp4-seg6bpf:~# iperf3 -c fc00::55
Connecting to host fc00::55, port 5201
[  4] local fc45::4 port 43062 connected to fc00::55 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.00   sec  1.03 GBytes  8.89 Gbits/sec    0    743 KBytes
[  4]   1.00-2.00   sec  1.03 GBytes  8.87 Gbits/sec    0    743 KBytes
[  4]   2.00-3.00   sec  1.03 GBytes  8.87 Gbits/sec    0    743 KBytes
Reported-by: Tom Herbert <tom@quantonium.net>
Fixes: 6c8702c6 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ceph fix from Ilya Dryomov:
 "A fix for a dio-enabled loop on ceph deadlock from Zheng, marked for
  stable"

* tag 'ceph-for-4.16-rc8' of git://github.com/ceph/ceph-client:
  ceph: only dirty ITER_IOVEC pages for direct read

Pull KVM fixes from Radim Krčmář:
 "PPC:
   - Fix a bug causing occasional machine check exceptions on POWER8
     hosts (introduced in 4.16-rc1)

  x86:
   - Fix a guest crashing regression with nested VMX and restricted
     guest (introduced in 4.16-rc1)

   - Fix dependency check for pv tlb flush (the wrong dependency that
     effectively disabled the feature was added in 4.16-rc4, the
     original feature in 4.16-rc1, so it got decent testing)"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Fix pv tlb flush dependencies
  KVM: nVMX: sync vmcs02 segment regs prior to vmx_set_cr0
  KVM: PPC: Book3S HV: Fix duplication of host SLB entries

Pull i2c fix from Wolfram Sang:
 "A simple but worthwhile I2C driver fix for 4.16"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i2c-stm32f7: fix no check on returned setup

Pull sound fixes from Takashi Iwai:
 "Very small fixes (all one-liners) at this time.

  One fix is for a PCM core stuff to correct the mmap behavior on
  non-x86. It doesn't show on most machines but mostly only for exotic
  non-interleaved formats"

* tag 'sound-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: pcm: potential uninitialized return values
  ALSA: pcm: Use dma_bytes as size parameter in dma_mmap_coherent()
  ALSA: usb-audio: Add native DSD support for TEAC UD-301

When calculating difference between samples, the values
are multiplied by 100. Large values may cause int overflow
when multiplied (usually on first iteration).
Fixed by forcing 100 to be of type unsigned long.

Fixes: 4c4dbb4a ("net/mlx5e: Move dynamic interrupt coalescing code to include/linux")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Toshiaki Makita says:

====================
Fix vlan tag handling for vlan packets without ethernet headers

Eric Dumazet reported syzbot found a new bug which leads to underflow of
size argument of memmove(), causing crash[1]. This can be triggered by tun
devices.

The underflow happened because skb_vlan_untag() did not expect vlan packets
without ethernet headers, and tun can produce such packets.
I also checked vlan_insert_inner_tag() and found a similar bug.

This series fixes these problems.

[1] https://marc.info/?l=linux-netdev&m=152221753920510&w=2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In some situation vlan packets do not have ethernet headers. One example
is packets from tun devices. Users can specify vlan protocol in tun_pi
field instead of IP protocol. When we have a vlan device with reorder_hdr
disabled on top of the tun device, such packets from tun devices are
untagged in skb_vlan_untag() and vlan headers will be inserted back in
vlan_insert_inner_tag().

vlan_insert_inner_tag() however did not expect packets without ethernet
headers, so in such a case size argument for memmove() underflowed.

We don't need to copy headers for packets which do not have preceding
headers of vlan headers, so skip memmove() in that case.
Also don't write vlan protocol in skb->data when it does not have enough
room for it.

Fixes: cbe7128c ("vlan: Fix out of order vlan headers with reorder header off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some situation vlan packets do not have ethernet headers. One example
is packets from tun devices. Users can specify vlan protocol in tun_pi
field instead of IP protocol, and skb_vlan_untag() attempts to untag such
packets.

skb_vlan_untag() (more precisely, skb_reorder_vlan_header() called by it)
however did not expect packets without ethernet headers, so in such a case
size argument for memmove() underflowed and triggered crash.

====
BUG: unable to handle kernel paging request at ffff8801cccb8000
IP: __memmove+0x24/0x1a0 arch/x86/lib/memmove_64.S:43
PGD 9cee067 P4D 9cee067 PUD 1d9401063 PMD 1cccb7063 PTE 2810100028101
Oops: 000b [#1] SMP KASAN
Dumping ftrace buffer:
   (ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 17663 Comm: syz-executor2 Not tainted 4.16.0-rc7+ #368
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__memmove+0x24/0x1a0 arch/x86/lib/memmove_64.S:43
RSP: 0018:ffff8801cc046e28 EFLAGS: 00010287
RAX: ffff8801ccc244c4 RBX: fffffffffffffffe RCX: fffffffffff6c4c2
RDX: fffffffffffffffe RSI: ffff8801cccb7ffc RDI: ffff8801cccb8000
RBP: ffff8801cc046e48 R08: ffff8801ccc244be R09: ffffed0039984899
R10: 0000000000000001 R11: ffffed0039984898 R12: ffff8801ccc244c4
R13: ffff8801ccc244c0 R14: ffff8801d96b7c06 R15: ffff8801d96b7b40
FS:  00007febd562d700(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff8801cccb8000 CR3: 00000001ccb2f006 CR4: 00000000001606e0
DR0: 0000000020000000 DR1: 0000000020000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000600
Call Trace:
 memmove include/linux/string.h:360 [inline]
 skb_reorder_vlan_header net/core/skbuff.c:5031 [inline]
 skb_vlan_untag+0x470/0xc40 net/core/skbuff.c:5061
 __netif_receive_skb_core+0x119c/0x3460 net/core/dev.c:4460
 __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4627
 netif_receive_skb_internal+0x10b/0x670 net/core/dev.c:4701
 netif_receive_skb+0xae/0x390 net/core/dev.c:4725
 tun_rx_batched.isra.50+0x5ee/0x870 drivers/net/tun.c:1555
 tun_get_user+0x299e/0x3c20 drivers/net/tun.c:1962
 tun_chr_write_iter+0xb9/0x160 drivers/net/tun.c:1990
 call_write_iter include/linux/fs.h:1782 [inline]
 new_sync_write fs/read_write.c:469 [inline]
 __vfs_write+0x684/0x970 fs/read_write.c:482
 vfs_write+0x189/0x510 fs/read_write.c:544
 SYSC_write fs/read_write.c:589 [inline]
 SyS_write+0xef/0x220 fs/read_write.c:581
 do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x454879
RSP: 002b:00007febd562cc68 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007febd562d6d4 RCX: 0000000000454879
RDX: 0000000000000157 RSI: 0000000020000180 RDI: 0000000000000014
RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000000006b0 R14: 00000000006fc120 R15: 0000000000000000
Code: 90 90 90 90 90 90 90 48 89 f8 48 83 fa 20 0f 82 03 01 00 00 48 39 fe 7d 0f 49 89 f0 49 01 d0 49 39 f8 0f 8f 9f 00 00 00 48 89 d1 <f3> a4 c3 48 81 fa a8 02 00 00 72 05 40 38 fe 74 3b 48 83 ea 20
RIP: __memmove+0x24/0x1a0 arch/x86/lib/memmove_64.S:43 RSP: ffff8801cc046e28
CR2: ffff8801cccb8000
====

We don't need to copy headers for packets which do not have preceding
headers of vlan headers, so skip memmove() in that case.

Fixes: 4bbb3e0e ("net: Fix vlan untag for bridge and vlan_dev with reorder_hdr off")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a page is already locked, attempting to dirty it leads to a deadlock
in lock_page().  This is what currently happens to ITER_BVEC pages when
a dio-enabled loop device is backed by ceph:

  $ losetup --direct-io /dev/loop0 /mnt/cephfs/img
  $ xfs_io -c 'pread 0 4k' /dev/loop0

Follow other file systems and only dirty ITER_IOVEC pages.

Cc: stable@kernel.org
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>

Merge tag 'for-4.16/dm-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix a DM multipath regression introduced in a v4.16-rc6 commit:
   restore support for loading, and attaching, scsi_dh modules during
   multipath table load. Otherwise some users may find themselves unable
   to boot, as was reported today:

     https://marc.info/?l=linux-scsi&m=152231276114962&w=2

 - Fix a DM core ioctl permission check regression introduced in a
   v4.16-rc5 commit.

* tag 'for-4.16/dm-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix dropped return code from dm_get_bdev_for_ioctl
  dm mpath: fix support for loading scsi_dh modules during table load

Pull rdma fixes from Jason Gunthorpe:
 "It has been fairly silent lately on our -rc front. Big queue of
  patches on the mailing list going to for-next though.

  Bug fixes:
   - qedr driver bugfixes causing application hangs, wrong uapi errnos,
     and a race condition
   - three syzkaller found bugfixes in the ucma uapi

  Regression fixes for things introduced in 4.16:
   - Crash on error introduced in mlx5 UMR flow
   - Crash on module unload/etc introduced by bad interaction of
     restrack and mlx5 patches this cycle
   - Typo in a two line syzkaller bugfix causing a bad regression
   - Coverity report of nonsense code in hns driver"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/ucma: Introduce safer rdma_addr_size() variants
  RDMA/hns: ensure for-loop actually iterates and free's buffers
  RDMA/ucma: Check that device exists prior to accessing it
  RDMA/ucma: Check that device is connected prior to access it
  RDMA/rdma_cm: Fix use after free race with process_one_req
  RDMA/qedr: Fix QP state initialization race
  RDMA/qedr: Fix rc initialization on CNQ allocation failure
  RDMA/qedr: fix QP's ack timeout configuration
  RDMA/ucma: Correct option size check using optlen
  RDMA/restrack: Move restrack_clean to be symmetrical to restrack_init
  IB/mlx5: Don't clean uninitialized UMR resources

Pull MTD fixes from Boris Brezillon:
 "Two fixes, one in the atmel NAND driver and another one in the
  CFI/JEDEC code.

  Summary:

   - Fix a bug in Atmel ECC engine driver

   - Fix a bug in the CFI/JEDEC driver"

* tag 'mtd/fixes-for-4.16' of git://git.infradead.org/linux-mtd:
  mtd: jedec_probe: Fix crash in jedec_read_mfr()
  mtd: nand: atmel: Fix get_sectorsize() function

dm_get_bdev_for_ioctl()'s return of 0 or 1 must be the result from
prepare_ioctl (1 means the ioctl was issued to a partition, 0 means it
wasn't).  Unfortunately commit 519049af ("dm: use blkdev_get rather
than bdgrab when issuing pass-through ioctl") reused the variable 'r'
to store the return from blkdev_get() that follows prepare_ioctl()
-- whereby dropping prepare_ioctl()'s result on the floor.

This can lead to an ioctl or persistent reservation being issued to a
partition going unnoticed, which implies the extra permission check for
CAP_SYS_RAWIO is skipped.

Fix this by using a different variable to store blkdev_get()'s return.

Fixes: 519049af ("dm: use blkdev_get rather than bdgrab when issuing pass-through ioctl")
Reported-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Daniel Borkman says:

====================
pull-request: bpf 2018-03-29

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix nfp to properly check max insn count while emitting
   instructions in the JIT which was wrongly comparing bytes
   against number of instructions before, from Jakub.

2) Fix for bpftool to avoid usage of hex numbers in JSON
   output since JSON doesn't accept hex numbers with 0x
   prefix, also from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The ability to have multipath dynamically attach a scsi_dh, that the user
specified in the multipath table, was broken by commit e8f74a0f ("dm
mpath: eliminate need to use scsi_device_from_queue").

Restore the ability to load, and attach, a particular scsi_dh module if
one is specified (as noticed by checking m->hw_handler_name).

Fixes: e8f74a0f ("dm mpath: eliminate need to use scsi_device_from_queue")
Reported-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Vq log_base is the userspace address of bitmap which has nothing to do
with IOTLB. So it needs to be validated unconditionally otherwise we
may try use 0 as log_base which may lead to pin pages that will lead
unexpected result (e.g trigger BUG_ON() in set_bit_to_user()).

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Today, driver drops received packets which are indicated as
invalid checksum by the device. Instead of dropping such packets,
pass them to the stack with CHECKSUM_NONE indication in skb.
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It turns out that the loop where we read manufacturer
jedec_read_mfd() can under some circumstances get a
CFI_MFR_CONTINUATION repeatedly, making the loop go
over all banks and eventually hit the end of the
map and crash because of an access violation:

Unable to handle kernel paging request at virtual address c4980000
pgd = (ptrval)
[c4980000] *pgd=03808811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] PREEMPT ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc1+ #150
Hardware name: Gemini (Device Tree)
PC is at jedec_probe_chip+0x6ec/0xcd0
LR is at 0x4
pc : [<c03a2bf4>]    lr : [<00000004>]    psr: 60000013
sp : c382dd18  ip : 0000ffff  fp : 00000000
r10: c0626388  r9 : 00020000  r8 : c0626340
r7 : 00000000  r6 : 00000001  r5 : c3a71afc  r4 : c382dd70
r3 : 00000001  r2 : c4900000  r1 : 00000002  r0 : 00080000
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 0000397f  Table: 00004000  DAC: 00000053
Process swapper (pid: 1, stack limit = 0x(ptrval))

Fix this by breaking the loop with a return 0 if
the offset exceeds the map size.

Fixes: 5c9c11e1 ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0")
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>

get_sectorsize() was not using the appropriate macro to extract the
ECC sector size from the config cache, which led to buggy ECC when
using 1024 byte sectors.

Fixes: f88fc122 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Reported-by: Olivier Schonken <olivier.schonken@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Olivier Schonken <olivier.schonken@gmail.com>

My recent change to netvsc drive in how receive flags are handled
broke multicast.  The Hyper-v/Azure virtual interface there is not a
multicast filter list, filtering is only all or none. The driver must
enable all multicast if any multicast address is present.

Fixes: 009f766c ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>