- 27 Jul, 2021 20 commits
-
-
Marek Vasut authored
Make sure the FIFO_CLEAR bit is latched in when configuring the controller, so that the FIFO is really cleared. And then clear the FIFO_CLEAR bit, since it is not self-clearing. Fixes: 45d59d70 ("drm: Add new driver for MXSFB controller") Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Daniel Abrecht <public@danielabrecht.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Stefan Agner <stefan@agner.ch> Reviewed-by:
Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # i.Core MX8MM Acked-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210620224946.189524-1-marex@denx.de
-
Marek Vasut authored
In case there is a bridge connected to the LCDIF, use bus_format from the bridge, otherwise behave as before and use bus_format from the connector. This way, even if there are multiple bridges in the display pipeline, the LCDIF will use the correct format. Reviewed-by:
-
Marek Vasut authored
In case the DRAM is under high load, the MXSFB FIFO might underflow and that causes visible artifacts. This could be triggered on i.MX8MM using e.g. "$ memtester 128M" on a device with 1920x1080 panel. The first "Stuck Address" test of the memtester will completely corrupt the image on the panel and leave the MXSFB FIFO in odd state. To avoid this underflow, increase number of outstanding requests to DRAM from 2 to 16, which is the maximum. This mitigates the issue and it can no longer be triggered. Fixes: 45d59d70 ("drm: Add new driver for MXSFB controller") Signed-off-by:
-
Marek Vasut authored
There is some sort of corner case behavior of the controller, which could rarely be triggered at least on i.MX6SX connected to 800x480 DPI panel and i.MX8MM connected to DPI->DSI->LVDS bridged 1920x1080 panel (and likely on other setups too), where the image on the panel shifts to the right and wraps around. This happens either when the controller is enabled on boot or even later during run time. The condition does not correct itself automatically, i.e. the display image remains shifted. It seems this problem is known and is due to sporadic underflows of the LCDIF FIFO. While the LCDIF IP does have underflow/overflow IRQs, neither of the IRQs trigger and neither IRQ status bit is asserted when this condition occurs. All known revisions of the LCDIF IP have CTRL1 RECOVER_ON_UNDERFLOW bit, which is described in the reference manual since i.MX23 as " Set this bit to enable the LCDIF block to recover in the next field/frame if there was an underflow in the current field/frame. " Enable this bit to mitigate the sporadic underflows. Fixes: 45d59d70 ("drm: Add new driver for MXSFB controller") Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
-
Geert Uytterhoeven authored
Cache the column and page ranges, to avoid doing unneeded I2C transfers when the values haven't changed. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Acked-by:
-
Geert Uytterhoeven authored
Currently, each screen update triggers an I2C transfer of all screen data, up to 1 KiB of data for a 128x64 display, which takes at least 20 ms in Fast mode. Reduce the amount of transferred data by only updating the rectangle that changed. Remove the calls to ssd1307fb_set_col_range() and ssd1307fb_set_page_range() during initialization, as ssd1307fb_update_rect() now takes care of that. Note that for now the optimized operation is only used for fillrect, copyarea, and imageblit, which are used by fbcon. Signed-off-by:
-
Geert Uytterhoeven authored
Extract the code to set the column and page ranges into two helper functions. Signed-off-by:
-
Geert Uytterhoeven authored
Simplify the nested loops to handle conversion from linear frame buffer to ssd1307 page layout: 1. Move last page handling one level up, as the value of "m" is the same inside a page, 2. array->data[] is filled linearly, so there is no need to recalculate array_idx over and over again; a simple increment is sufficient. Signed-off-by: -
Geert Uytterhoeven authored
Make ssd1307fb_update_display() return an error code, so callers that can handle failures can propagate it. Signed-off-by:
-
Simon Ser authored
Since there's no struct to attach the docs to, document the IOCTL definition. Signed-off-by:
Simon Ser <contact@emersion.fr> Reviewed-by:
Pekka Paalanen <pekka.paalanen@collabora.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Leandro Ribeiro <leandro.ribeiro@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/ephVkof3uGu2RpOdBbrHE3qF98zBfIBRzXe4Vyoboh0@cp4-web-034.plabs.ch
-
Simon Ser authored
We already have logging for ADDFB2. Add some logging for RMFB as well. This can be handy when trying to find out why a CRTC gets magically disabled. v2: make log message more explicit, add log messages to drm_framebuffer_remove (Daniel) Signed-off-by:
-
Maarten Lankhorst authored
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes. Signed-off-by:Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-
Daniel Vetter authored
We're trying to have a fairly strict split between core functionality that defines the uapi, including the docs, and the helper functions to implement it. Move drm_plane_enable_fb_damage_clips and associated kerneldoc into drm_plane from drm_damage_helper.c to fix this. Reviewed-by:
José Roberto de Souza <jose.souza@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210723083457.696939-3-daniel.vetter@ffwll.ch
-
Daniel Vetter authored
There's two stages of manual upload/invalidate displays: - just handling dirtyfb and uploading the entire fb all the time - looking at damage clips In the latter case we support it through fbdev emulation (with fb_defio), atomic property, and with the dirtfy clip rects. Make sure at least the atomic property is set up as the main official interface for this. Ideally we'd also check that drm_atomic_helper_dirtyfb() is used and that fbdev defio is set up, but that's quite a bit harder to do. Ideas very much welcome. From a cursor audit drivers seem to be getting this right mostly, but better to make sure. At least no one is bypassing the accessor function. v2: - use drm_warn_once with a meaningful warning string (José) - don't splat in the atomic check code for everyone (intel-gfx-ci) Reviewed-by: José Roberto de Souza <jose.souza@intel.com> (v1) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Daniel Vetter authored
It's not used. Drivers should instead use the helpers anyway. Currently both vbox and i915 hand-roll this and it's not the greatest. vbox looks buggy, and i915 does a bit much that helpers would take care of I think. Also improve the kerneldocs while we're at it. Reviewed-by:
-
Jose Maria Casanova Crespo authored
s/Exporting/Importing Fixes: 805dc614 ("drm/prime: Update docs") Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
Jose Maria Casanova Crespo <jmcasanova@igalia.com> Signed-off-by:
-
Jagan Teki authored
Finding panel_or_bridge might vary based on associated DSI devices like DSI panel, bridge, and I2C based DSI bridge. 1. DSI panels and bridges will invoke the host attach from probe in order to find the panel_or_bridge. chipone_probe() dw_mipi_dsi_host_attach().start dw_mipi_dsi_panel_or_bridge() ...found the panel_or_bridge... ltdc_encoder_init().start dw_mipi_dsi_bridge_attach().start dw_mipi_dsi_host_attach().start chipone_attach(). start chipone_attach(). done dw_mipi_dsi_host_attach().done dw_mipi_dsi_bridge_attach(). done ltdc_encoder_init().done 2. I2C based DSI bridge will invoke the drm_bridge_attach from bridge attach in order to find the panel_or_bridge. ltdc_encoder_init().start dw_mipi_dsi_bridge_attach().start dw_mipi_dsi_panel_or_bridge() ...found the panel_or_bridge... dw_mipi_dsi_host_attach().start sn65dsi83_attach(). start sn65dsi83_attach(). done dw_mipi_dsi_host_attach().done dw_mipi_dsi_bridge_attach(). done ltdc_encoder_init().done So, invoke the panel_or_bridge from host attach and bridge attach in order to find all possible DSI devices. Signed-off-by:Yannick Fertre <yannick.fertre@foss.st.com> Reviewed-by:
Robert Foss <robert.foss@linaro.org> Tested-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Randy Dunlap authored
When # CONFIG_EFI is not set, there are 2 definitions of sysfb_apply_efi_quirks(). The stub from sysfb.h should be used and the __init function from sysfb_efi.c should not be used. ../drivers/firmware/efi/sysfb_efi.c:337:13: error: redefinition of ‘sysfb_apply_efi_quirks’ __init void sysfb_apply_efi_quirks(struct platform_device *pd) ^~~~~~~~~~~~~~~~~~~~~~ In file included from ../drivers/firmware/efi/sysfb_efi.c:26:0: ../include/linux/sysfb.h:65:20: note: previous definition of ‘sysfb_apply_efi_quirks’ was here static inline void sysfb_apply_efi_quirks(struct platform_device *pd) ^~~~~~~~~~~~~~~~~~~~~~ Reviewed-by:Javier Martinez Canillas <javierm@redhat.com> Fixes: 8633ef82 ("drivers/firmware: consolidate EFI framebuffer setup for all arches") Acked-by:
Ard Biesheuvel <ardb@kernel.org> Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Ard Biesheuvel <ardb@kernel.org> Cc: linux-efi@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Cc: Javier Martinez Canillas <javierm@redhat.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Mark Brown <broonie@kernel.org> Cc: linux-next@vger.kernel.org Signed-off-by:
-
Javier Martinez Canillas authored
The Generic System Framebuffers support is built when the COMPILE_TEST option is enabled. But this wrongly assumes that all the architectures declare a struct screen_info. This is true for most architectures, but at least the following do not: arc, m68k, microblaze, openrisc, parisc and s390. By attempting to make this compile testeable on all architectures, it leads to linking errors as reported by the kernel test robot for parisc: All errors (new ones prefixed by >>): hppa-linux-ld: drivers/firmware/sysfb.o: in function `sysfb_init': (.init.text+0x24): undefined reference to `screen_info' >> hppa-linux-ld: (.init.text+0x28): undefined reference to `screen_info' To prevent these errors only allow sysfb to be built on systems that are going to need it, which are x86 BIOS and EFI. The EFI Kconfig symbol is used instead of (ARM || ARM64 || RISC) because some of these architectures only declare a struct screen_info if EFI is enabled. And also, because the SYSFB code is only used for EFI on these architectures. For !EFI the "simple-framebuffer" device is registered by OF when parsing the Device Tree Blob (if a DT node for this was defined). Fixes: d391c582 ("drivers/firmware: move x86 Generic System Framebuffers support") Reported-by:kernel test robot <lkp@intel.com> Signed-off-by:
-
Nicolas Boichat authored
Many of the DSI flags have names opposite to their actual effects, e.g. MIPI_DSI_MODE_EOT_PACKET means that EoT packets will actually be disabled. Fix this by including _NO_ in the flag names, e.g. MIPI_DSI_MODE_NO_EOT_PACKET. Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Andrzej Hajda <andrzej.hajda@samsung.com> Reviewed-by: Xin Ji <xji@analogixsemi.com> # anx7625.c Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> # msm/dsi Signed-off-by:
-
- 26 Jul, 2021 8 commits
-
-
Alexander Sverdlin authored
Use clk_prepare_enable()/clk_disable_unprepare() in preparation for switch to Common Clock Framework. Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by:
Nikita Shubin <nikita.shubin@maquefel.me> Signed-off-by:
-
Artjom Vejsel authored
Add vendor prefix for Shenzhen QiShenglong Industrialist Co., Ltd. QiShenglong is a Chinese manufacturer of handheld gaming consoles, most of which run (very old) versions of Linux. QiShenglong is known as Hamy. Signed-off-by:
Artjom Vejsel <akawolf0@gmail.com> Signed-off-by:
-
Bjorn Andersson authored
Add definition of the AUO B133HAN05.4 13.3" FHD panel and the B140HAN06.4 14.0" FHD panel. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Bjorn Andersson authored
Add bindings for the two AUO panels B133HAN05 and B140HAN06, both 1920x1080 panels with 16.7M colors, first being 13.3" and the latter 14.0". Signed-off-by:
-
Zheyu Ma authored
The userspace program could pass any values to the driver through ioctl() interface. If the driver doesn't check the value of 'pixclock', it may cause divide error. Fix this by checking whether 'pixclock' is zero first. The following log reveals it: [ 33.396850] divide error: 0000 [#1] PREEMPT SMP KASAN PTI [ 33.396864] CPU: 5 PID: 11754 Comm: i740 Not tainted 5.14.0-rc2-00513-gac532c9bbcfb-dirty #222 [ 33.396883] RIP: 0010:riva_load_video_mode+0x417/0xf70 [ 33.396969] Call Trace: [ 33.396973] ? debug_smp_processor_id+0x1c/0x20 [ 33.396984] ? tick_nohz_tick_stopped+0x1a/0x90 [ 33.396996] ? rivafb_copyarea+0x3c0/0x3c0 [ 33.397003] ? wake_up_klogd.part.0+0x99/0xd0 [ 33.397014] ? vprintk_emit+0x110/0x4b0 [ 33.397024] ? vprintk_default+0x26/0x30 [ 33.397033] ? vprintk+0x9c/0x1f0 [ 33.397041] ? printk+0xba/0xed [ 33.397054] ? record_print_text.cold+0x16/0x16 [ 33.397063] ? __kasan_check_read+0x11/0x20 [ 33.397074] ? profile_tick+0xc0/0x100 [ 33.397084] ? __sanitizer_cov_trace_const_cmp4+0x24/0x80 [ 33.397094] ? riva_set_rop_solid+0x2a0/0x2a0 [ 33.397102] rivafb_set_par+0xbe/0x610 [ 33.397111] ? riva_set_rop_solid+0x2a0/0x2a0 [ 33.397119] fb_set_var+0x5bf/0xeb0 [ 33.397127] ? fb_blank+0x1a0/0x1a0 [ 33.397134] ? lock_acquire+0x1ef/0x530 [ 33.397143] ? lock_release+0x810/0x810 [ 33.397151] ? lock_is_held_type+0x100/0x140 [ 33.397159] ? ___might_sleep+0x1ee/0x2d0 [ 33.397170] ? __mutex_lock+0x620/0x1190 [ 33.397180] ? trace_hardirqs_on+0x6a/0x1c0 [ 33.397190] do_fb_ioctl+0x31e/0x700 Signed-off-by:
Zheyu Ma <zheyuma97@gmail.com> Signed-off-by:
-
Zheyu Ma authored
The userspace program could pass any values to the driver through ioctl() interface. if the driver doesn't check the value of 'pixclock', it may cause divide error because the value of 'lineclock' and 'frameclock' will be zero. Fix this by checking whether 'pixclock' is zero in kyrofb_check_var(). The following log reveals it: [ 103.073930] divide error: 0000 [#1] PREEMPT SMP KASAN PTI [ 103.073942] CPU: 4 PID: 12483 Comm: syz-executor Not tainted 5.14.0-rc2-00478-g2734d6c1-dirty #118 [ 103.073959] RIP: 0010:kyrofb_set_par+0x316/0xc80 [ 103.074045] Call Trace: [ 103.074048] ? ___might_sleep+0x1ee/0x2d0 [ 103.074060] ? kyrofb_ioctl+0x330/0x330 [ 103.074069] fb_set_var+0x5bf/0xeb0 [ 103.074078] ? fb_blank+0x1a0/0x1a0 [ 103.074085] ? lock_acquire+0x3bd/0x530 [ 103.074094] ? lock_release+0x810/0x810 [ 103.074103] ? ___might_sleep+0x1ee/0x2d0 [ 103.074114] ? __mutex_lock+0x620/0x1190 [ 103.074126] ? trace_hardirqs_on+0x6a/0x1c0 [ 103.074137] do_fb_ioctl+0x31e/0x700 [ 103.074144] ? fb_getput_cmap+0x280/0x280 [ 103.074152] ? rcu_read_lock_sched_held+0x11/0x80 [ 103.074162] ? rcu_read_lock_sched_held+0x11/0x80 [ 103.074171] ? __sanitizer_cov_trace_switch+0x67/0xf0 [ 103.074181] ? __sanitizer_cov_trace_const_cmp2+0x20/0x80 [ 103.074191] ? do_vfs_ioctl+0x14b/0x16c0 [ 103.074199] ? vfs_fileattr_set+0xb60/0xb60 [ 103.074207] ? rcu_read_lock_sched_held+0x11/0x80 [ 103.074216] ? lock_release+0x483/0x810 [ 103.074224] ? __fget_files+0x217/0x3d0 [ 103.074234] ? __fget_files+0x239/0x3d0 [ 103.074243] ? do_fb_ioctl+0x700/0x700 [ 103.074250] fb_ioctl+0xe6/0x130 Signed-off-by:
-
Zheyu Ma authored
The userspace program could pass any values to the driver through ioctl() interface. If the driver doesn't check the value of 'pixclock', it may cause divide error. Fix this by checking whether 'pixclock' is zero first. The following log reveals it: [ 43.861711] divide error: 0000 [#1] PREEMPT SMP KASAN PTI [ 43.861737] CPU: 2 PID: 11764 Comm: i740 Not tainted 5.14.0-rc2-00513-gac532c9bbcfb-dirty #224 [ 43.861756] RIP: 0010:asiliantfb_check_var+0x4e/0x730 [ 43.861843] Call Trace: [ 43.861848] ? asiliantfb_remove+0x190/0x190 [ 43.861858] fb_set_var+0x2e4/0xeb0 [ 43.861866] ? fb_blank+0x1a0/0x1a0 [ 43.861873] ? lock_acquire+0x1ef/0x530 [ 43.861884] ? lock_release+0x810/0x810 [ 43.861892] ? lock_is_held_type+0x100/0x140 [ 43.861903] ? ___might_sleep+0x1ee/0x2d0 [ 43.861914] ? __mutex_lock+0x620/0x1190 [ 43.861921] ? do_fb_ioctl+0x313/0x700 [ 43.861929] ? mutex_lock_io_nested+0xfa0/0xfa0 [ 43.861936] ? __this_cpu_preempt_check+0x1d/0x30 [ 43.861944] ? _raw_spin_unlock_irqrestore+0x46/0x60 [ 43.861952] ? lockdep_hardirqs_on+0x59/0x100 [ 43.861959] ? _raw_spin_unlock_irqrestore+0x46/0x60 [ 43.861967] ? trace_hardirqs_on+0x6a/0x1c0 [ 43.861978] do_fb_ioctl+0x31e/0x700 Signed-off-by:
-
Simon Ser authored
When a property has the type DRM_MODE_PROP_BITMASK, the value field stores a bitshift, not a bitmask, which can be surprising. Signed-off-by:
-
- 25 Jul, 2021 12 commits
-
-
Dave Airlie authored
Linux 5.14-rc3 Daniel said we should pull the nouveau fix from fixes in here, probably a good plan. Signed-off-by:Dave Airlie <airlied@redhat.com>
-
Linus Torvalds authored
-
Alyssa Rosenzweig authored
Like many free software projects, freedesktop.org issued a non-binding recommendation for projects to migrate from Freenode to OFTC [1]. As such, freedesktop.org entries in the MAINTAINERS file are out-of-date as the respective channels have moved. Update the file to point to the right network. v2: Correct typo in commit message pointed out by Lukas and Jonathan. Add Hector's ack. v3: Add acks. [1] https://lists.freedesktop.org/archives/dri-devel/2021-May/307605.htmlSigned-off-by:
Alyssa Rosenzweig <alyssa@rosenzweig.io> Acked-by:
Hector Martin <marcan@marcan.st> Acked-by:
Jani Nikula <jani.nikula@intel.com> Cc: Karol Herbst <kherbst@redhat.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Lukas Wunner <lukas@wunner.de> Cc: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Cc: linux-kernel@vger.kernel.org Signed-off-by:
Karol Herbst <kherbst@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210725150007.2818-2-alyssa@rosenzweig.io
-
Alyssa Rosenzweig authored
Like many free software projects, Nouveau recently moved from Freenode to OFTC. Update the reference. v3: Add acks. Signed-off-by:
-
Linus Torvalds authored
gcc doesn't care, but clang quite reasonably pointed out that the recent commit e9ba16e6 ("smpboot: Mark idle_init() as __always_inlined to work around aggressive compiler un-inlining") did some really odd things: kernel/smpboot.c:50:20: warning: duplicate 'inline' declaration specifier [-Wduplicate-decl-specifier] static inline void __always_inline idle_init(unsigned int cpu) ^ which not only has that duplicate inlining specifier, but the new __always_inline was put in the wrong place of the function definition. We put the storage class specifiers (ie things like "static" and "extern") first, and the type information after that. And while the compiler may not care, we put the inline specifier before the types. So it should be just static __always_inline void idle_init(unsigned int cpu) instead. Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: - Fix guest to host memory corruption in H_RTAS due to missing nargs check. - Fix guest triggerable host crashes due to bad handling of nested guest TM state. - Fix possible crashes due to incorrect reference counting in kvm_arch_vcpu_ioctl(). - Two commits fixing some regressions in KVM transactional memory handling introduced by the recent rework of the KVM code. Thanks to Nicholas Piggin, Alexey Kardashevskiy, and Michael Neuling. * tag 'powerpc-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: KVM: PPC: Book3S HV Nested: Sanitise H_ENTER_NESTED TM state KVM: PPC: Book3S: Fix H_RTAS rets buffer overflow KVM: PPC: Fix kvm_arch_vcpu_ioctl vcpu_load leak KVM: PPC: Book3S: Fix CONFIG_TRANSACTIONAL_MEM=n crash KVM: PPC: Book3S HV P9: Fix guest TM support
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "A small set of timer related fixes: - Plug a race between rearm and process tick in the posix CPU timers code - Make the optimization to avoid recalculation of the next timer interrupt work correctly when there are no timers pending" * tag 'timers-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timers: Fix get_next_timer_interrupt() with no timers pending posix-cpu-timers: Fix rearm racing against process tick -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 jump label fix from Thomas Gleixner: "A single fix for jump labels to prevent the compiler from agressive un-inlining which results in a section mismatch" * tag 'locking-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: jump_labels: Mark __jump_label_transform() as __always_inlined to work around aggressive compiler un-inlining
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull EFI fixes from Thomas Gleixner: "A set of EFI fixes: - Prevent memblock and I/O reserved resources to get out of sync when EFI memreserve is in use. - Don't claim a non-existing table is invalid - Don't warn when firmware memory is already reserved correctly" * tag 'efi-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: efi/mokvar: Reserve the table only if it is in boot services data efi/libstub: Fix the efi_load_initrd function description firmware/efi: Tell memblock about EFI iomem reservations efi/tpm: Differentiate missing and invalid final event log table. -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull core fix from Thomas Gleixner: "A single update for the boot code to prevent aggressive un-inlining which causes a section mismatch" * tag 'core-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: smpboot: Mark idle_init() as __always_inlined to work around aggressive compiler un-inlining
-
git://git.infradead.org/users/hch/dma-mappingLinus Torvalds authored
Pull dma-mapping fix from Christoph Hellwig: - handle vmalloc addresses in dma_common_{mmap,get_sgtable} (Roman Skakun) * tag 'dma-mapping-5.14-1' of git://git.infradead.org/users/hch/dma-mapping: dma-mapping: handle vmalloc addresses in dma_common_{mmap,get_sgtable} -
Heiko Stuebner authored
SoCs like the rk3288 and rk3399 have 3 mipi dphys on them. One is TX- only, one is RX-only and one can be configured to do either TX or RX. The RX phy is statically connected to the first Image Signal Processor, the TX phy is statically connected to the first DSI controller and the TXRX phy is connected to both the second DSI controller as well as the second ISP. The RX dphy is controlled externally through registers in the "General Register Files", while the other two are controlled through the "Configuration and Test Interface" inside their DSI controller's io-memory area. The Rockchip dw-dsi controller already controls these dphys for the TX case in the driver, but when we want to also allow configuration for RX to the ISP from the media subsystem we need to expose phy- functionality instead. So add a bit of infrastructure to allow the dsi driver to work as a phy and make sure it can be only one or the other at a time. Similarly as the dsi-controller will be part of the drm-graph when active, add an empty component to the drm-graph when in phy-mode to make the rest of the drm-graph not wait for it. Signed-off-by:
Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Tested-by:
Sebastian Fricke <sebastian.fricke@posteo.net> Acked-by:
Helen Koike <helen.koike@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210210111020.2476369-4-heiko@sntech.de
-
