The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add IPROC SDHCI driver for IPROC family of Broadcom devices.
Acked-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add device tree binding documentation for IPROC SDHCI driver.
Acked-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For CMD53 in block mode, the host does not need to stop the transfer,
as it stops when the block count (present in CMD53) is reached.
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add quirk to handle broken auto-CMD23.
Some controllers do not respond after the first auto-CMD23 is issued.

This allows CMD23 to still work (mandatory for the faster UHS-I mode)
rather than disabling CMD23 entirely via SDHCI_QUIRK2_HOST_NO_CMD23.

Signed-off by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Static checkers suggest that probably we intended to put curly braces
around the writel() to make it part of the else path.  But, I think
actually the indenting is off and the code works fine as is.

The stray tab was introduced in 0322191e ('mmc: sdhci-esdhc-imx: add
sd3.0 SDR clock tuning support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If CONFIG_DEBUG_SLAB=y:

    sh_mobile_sdhi ee100000.sd: Got CD GPIO
    sh_mobile_sdhi ee100000.sd: Got WP GPIO
    platform ee100000.sd: Driver sh_mobile_sdhi requests probe deferral
    ...
    Slab corruption (Not tainted): kmalloc-1024 start=ed8b3c00, len=1024
    2d0: 00 00 00 00 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  ....kkkkkkkkkkkk
    Prev obj: start=ed8b3800, len=1024
    000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk
    010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk

Struct tmio_mmc_host is embedded inside struct mmc_host, and thus is
freed by the call to mmc_free_host(). Hence it must not be written to
afterwards, as that will corrupt freed (and perhaps already reused)
memory.

Fixes: 94b110af ("mmc: tmio: add tmio_mmc_host_alloc/free()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SET_SYSTEM_SLEEP_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
omap_hsmmc_x callbacks under CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[Grygorii.Strashko@linaro.org: rebased on top of K4.0]
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Mobile phones (some) have no card detect pin, but can detect if the
cover is removed. The purpose is the same; detect if card is being
added/removed, but the details differ.
When the cover is removed, it does not mean the card is gone. But it
might, since it is accessible now. It's like a warning. All the driver
does is to limit write access to the card, see protect_card flag.
In contrast, card detect notifies us after the fact, e.g.
card is gone, card is inserted. We can't take precautions, but we can
rely on those events, -- the card is really gone, or do scan the card.
To summarize there is not much code sharing between cover and card
detect, it only increases confusion. By splitting, both will be
simplified in a followup patch.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The indirection via omap_hsmmc_get_ro and omap_hsmmc_get_wp is
redundant. Also dropped setting gpio_wp to EINVAL since platform date
is read-only
Untested: no device with ro pin was available, but change is fairly
simple
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

addon to: 09108968b7b72b6083a3bfc8f8259a74ed57255e
    mmc: omap_hsmmc: remove prepare/complete system suspend support
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The reset control for the sunxi mmc controller is optional. Some
newer platforms (sun6i, sun8i, sun9i) have it, while older ones
(sun4i, sun5i, sun7i) don't.

Use the properly stubbed _optional version so the driver does not
fail to compile when RESET_CONTROLLER=n.

This patch also adds a check for deferred probing on the reset
control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 3.16+
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In these drivers, the driver specific .remove function just a simple
wrapper of function sdhci_pltfm_unregister(). So remove these wrappers
and just set .remove to sdhci_pltfm_unregister().
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

So we can avoid to sprinkle the clk_disable_unprepare() in many
drivers.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Actually we can use the "clk" in the struct sdhci_pltfm_host. Also
change the "external clock" to "core clock" and kill two redundant
private functions in this driver as suggested by Ray Jui.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Actually we can use the "clk" in the struct sdhci_pltfm_host.
With this change we can also kill the private function for get
max clock in this driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Simplify the error and remove path.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is only one "clk" member in this driver specific private struct.
Actually we can use the "clk" member in the struct sdhci_pltfm_host,
and then kill this struct completely.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The function clk_disable_unprepare() already take care of either error
or null cases.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For the original tuning code, delay value is set to SD Bus Clock Delay
Register (SD_CLK_DELAY_SETTING) as (val | (Val << 7) | (val << 16)),
which means CLK_DELAY_IN1, CLK_DELAY_IN2 and CLK_DELAY_OUT are the
same and with 128 steps. This is doubtful. In CSR design specification
documents CS-304575-DR-3H, this issue is clarified, the delay[13:0] in
SD_CLK_DELAY_SETTING is simplied to the concatenation of {CLK_DELAY_IN2,
CLK_DELAY_IN1}.
Besides, for CMD19 tuning, no need to set CLK_DELAY_OUT([22,16]
of SD_CLK_DELAY_SETTING).
Signed-off-by: weijun yang <york.yang@csr.com>
Signed-off-by: Barry Song <baohua.song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's unlikely that this is really needed on any single-slot systems
where we disable card detects until the end of probe, but it still
seems safer to check to make sure that a slot has been initted before
we try to dereference it to find the SDIO interrupt mask.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We really don't want to get a card detect interrupt during probe time
since it can confuse things.  Let's disable the card detect interrupt
until we're in a really good place: the end of probe.  Let's also
simply avoid enabling the card detect interrupt if it's not used.

It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt.  That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host().  On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children.  I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:

Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host

Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.

The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.

We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command.  This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.

Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We should give dw_mmc a good reset after we apply power.  On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.

Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It appears that we can confuse things if we try to turn on the MMC
clock when the power is off.  Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The STOP command can terminate a data transfer between a memory card and
mmc controller.

As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.

After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

To support HS200 and UHS mode, mmc core will call init_card() to
execute tuning:
- sdio: init_card can be executed at runtime resume.
- sd and mmc: init_card can be executed at resume or runtime resume,
  which depends on MMC_CAP_RUNTIME_RESUME capability.

On rk3288 SoC, host will get DRTO interrupt when host send command
to read tuning data. This will spend more than 111ms:
drto_ms = drto_clks * 1000 / bus_hz = 111ms.

And the total tuning time will be more than 400ms.

So we should add MMC_CAP_RUNTIME_RESUME capability to execute tuning
at runtime resume. Only if we do so, can we pass resume test.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull bugfix for md from Neil Brown:
 "One fix for md in 4.0-rc4

  Regression in recent patch causes crash on error path"

* tag 'md/4.0-rc4-fix' of git://neil.brown.name/md:
  md: fix problems with freeing private data after ->run failure.

Pull driver core fixes from Greg KH:
 "Here are two bugfixes for things reported.  One regression in kernfs,
  and another issue fixed in the LZ4 code that was fixed in the
  "upstream" codebase that solves a reported kernel crash

  Both have been in linux-next for a while"

* tag 'driver-core-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  LZ4 : fix the data abort issue
  kernfs: handle poll correctly on 'direct_read' files.

Pull char/misc fixes from Greg KH:
 "Here are three fixes for 4.0-rc5 that revert 3 PCMCIA patches that
  were merged in 4.0-rc1 that cause regressions.  So let's revert them
  for now and they will be reworked and resent sometime in the future.

  All have been tested in linux-next for a while"

* tag 'char-misc-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Revert "pcmcia: add a new resource manager for non ISA systems"
  Revert "pcmcia: fix incorrect bracketing on a test"
  Revert "pcmcia: add missing include for new pci resource handler"

Pull staging driver fixes from Greg KH:
 "Here are four small staging driver fixes, all for the vt6656 and
  vt6655 drivers, that resolve some reported issues with them.

  All of these patches have been in linux next for a while"

* tag 'staging-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  vt6655: Fix late setting of byRFType.
  vt6655: RFbSetPower fix missing rate RATE_12M
  staging: vt6656: vnt_rf_setpower: fix missing rate RATE_12M
  staging: vt6655: vnt_tx_packet fix dma_idx selection.

Pull tty/serial driver fix from Greg KH:
 "Here's a single 8250 serial driver that fixes a reported deadlock with
  the serial console and the tty driver.

  It's been in linux-next for a while now"

* tag 'tty-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250_dw: Fix deadlock in LCR workaround

Pull USB / PHY driver fixes from Greg KH:
 "Here's a number of USB and PHY driver fixes for 4.0-rc5.

  The largest thing here is a revert of a gadget function driver patch
  that removes 500 lines of code.  Other than that, it's a number of
  reported bugs fixes and new quirk/id entries.

  All have been in linux-next for a while"

* tag 'usb-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  usb: common: otg-fsm: only signal connect after switching to peripheral
  uas: Add US_FL_NO_ATA_1X for Initio Corporation controllers / devices
  USB: ehci-atmel: rework clk handling
  MAINTAINERS: add entry for USB OTG FSM
  usb: chipidea: otg: add a_alt_hnp_support response for B device
  phy: omap-usb2: Fix missing clk_prepare call when using old dt name
  phy: ti/omap: Fix modalias
  phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
  phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
  phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
  phy: twl4030-usb: Remove redundant assignment for twl->linkstat
  phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
  phy: Find the right match in devm_phy_destroy()
  phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
  phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
  phy: samsung-usb2: Remove NULL terminating entry from phys array
  phy: hix5hd2-sata: Check return value of platform_get_resource
  phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
  Revert "usb: gadget: zero: Add support for interrupt EP"
  Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"
  ...

Pull slave dmaengine fixes from Vinod Koul:
 "Four fixes for dw, pl08x, imx-sdma and at_hdmac driver.  Nothing
  unusual here, simple fixes to these drivers"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: pl08x: Define capabilities for generic capabilities reporting
  dmaengine: dw: append MODULE_ALIAS for platform driver
  dmaengine: imx-sdma: switch to dynamic context mode after script loaded
  dmaengine: at_hdmac: Fix calculation of the residual bytes

Pull power management and ACPI fixes from Rafael Wysocki:
 "These are fixes for recent regressions (PCI/ACPI resources and at91
  RTC locking), a stable-candidate powercap RAPL driver fix and two ARM
  cpuidle fixes (one stable-candidate too).

  Specifics:

   - Revert a recent PCI commit related to IRQ resources management that
     introduced a regression for drivers attempting to bind to devices
     whose previous drivers did not balance pci_enable_device() and
     pci_disable_device() as expected (Rafael J Wysocki).

   - Fix a deadlock in at91_rtc_interrupt() introduced by a typo in a
     recent commit related to wakeup interrupt handling (Dan Carpenter).

   - Allow the power capping RAPL (Running-Average Power Limit) driver
     to use different energy units for domains within one CPU package
     which is necessary to handle Intel Haswell EP processors correctly
     (Jacob Pan).

   - Improve the cpuidle mvebu driver's handling of Armada XP SoCs by
     updating the target residency and exit latency numbers for those
     chips (Sebastien Rannou).

   - Prevent the cpuidle mvebu driver from calling cpu_pm_enter() twice
     in a row before cpu_pm_exit() is called on the same CPU which
     breaks the core's assumptions regarding the usage of those
     functions (Gregory Clement)"

* tag 'pm+acpi-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "x86/PCI: Refine the way to release PCI IRQ resources"
  rtc: at91rm9200: double locking bug in at91_rtc_interrupt()
  powercap / RAPL: handle domains with different energy units
  cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
  cpuidle: mvebu: Fix the CPU PM notifier usage

Pull drm updates from Dave Airlie:
 "A bunch of fixes across drivers:

  radeon:
     disable two ended allocation for now, it breaks some stuff

  amdkfd:
     misc fixes

  nouveau:
     fix irq loop problem, add basic support for GM206 (new hw)

  i915:
     fix some WARNs people were seeing

  exynos:
     fix some iommu interactions causing boot failures"

* git://people.freedesktop.org/~airlied/linux:
  drm/radeon: drop ttm two ended allocation
  drm/exynos: fix the initialization order in FIMD
  drm/exynos: fix typo config name correctly.
  drm/exynos: Check for NULL dereference of crtc
  drm/exynos: IS_ERR() vs NULL bug
  drm/exynos: remove unused files
  drm/i915: Make sure the primary plane is enabled before reading out the fb state
  drm/nouveau/bios: fix i2c table parsing for dcb 4.1
  drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
  drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
  drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
  drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
  drm/radeon: Changing number of compute pipe lines
  drm/amdkfd: Fix SDMA queue init. in non-HWS mode
  drm/amdkfd: destroy mqd when destroying kernel queue
  drm/i915: Ensure plane->state->fb stays in sync with plane->fb

Merge tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull more DeviceTree fixes vfom Rob Herring:

 - revert setting stdout-path as preferred console.  This caused
   regressions in PowerMACs and other systems.

 - yet another fix for stdout-path option parsing.

 - fix error path handling in of_irq_parse_one

* tag 'devicetree-fixes-for-4.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  Revert "of: Fix premature bootconsole disable with 'stdout-path'"
  of: handle both '/' and ':' in path strings
  of: unittest: Add option string test case with longer path
  of/irq: Fix of_irq_parse_one() returned error codes