GPHY revision G0 has its version rolled over to 0x10, introduce an
explicit check for that revision and invoke the proper workaround
function for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with GPHY revision G0, the GENET register layout has changed to
use the same numbering scheme as the Starfighter 2 switch. This means
that GPHY major revision is in bits 15:12, minor in bits 11:8 and patch
level is in bits 7:4.

Introduce a small heuristic which checks for the old scheme first, tests
for the new scheme and finally attempts to catch reserved values and
aborts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2014-12-03

1) Fix a set but not used warning. From Fabian Frederick.

2) Currently we make sequence number values available to userspace
   only if we use ESN. Make the sequence number values also available
   for non ESN states. From Zhi Ding.

3) Remove socket policy hashing. We don't need it because socket
   policies are always looked up via a linked list. From Herbert Xu.

4) After removing socket policy hashing, we can use __xfrm_policy_link
   in xfrm_policy_insert. From Herbert Xu.

5) Add a lookup method for vti6 tunnels with wildcard endpoints.
   I forgot this when I initially implemented vti6.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

David L Stevens says:

====================
sunvnet: add SG, HW_CSUM, GSO, and TSO support

This patch set adds everything needed for TSO support in sunvnet. On my
test hardware, this increases the single-stream TCP throughput for the
default 1500-byte MTU Linux-Linux from ~2Gbps to 10Gbps and Linux-Solaris
from ~2Gbps to 6Gbps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds TSO support for the sunvnet driver.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds GSO support to the sunvnet driver.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for sender-side checksum offloading.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds scatter/gather support to the sunvnet driver.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for VIO v1.7 (extended descriptor format)
and v1.8 (receive-side checksumming) to the sunvnet driver.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the name of vnet_port_alloc_tx_bufs to
vnet_port_alloc_tx_ring, since there are no buffer allocations after
transmit zero copy support was added. This patch also moves the ring
allocation to after VIO version negotiation to allow for
different-sized descriptors in later VIO versions.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
ethtool, net/mlx4_en: RSS hash function selection

This patchset by Eyal adds support in set/get of RSS hash function. Current
supported functions are Toeplitz and XOR. The API is design to enable adding
new hash functions without breaking backward compatibility.
Userspace patch will be sent after API is available in kernel.

The patchset was applied and tested over commit cd4c910e ("netpoll: delete
defconfig references to obsolete NETPOLL_TRAP")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The ConnectX HW is capable of using one of the following hash functions:
Toeplitz and an XOR hash function. This patch extends the implementation
of the mlx4_en driver set/get_rxfh callbacks to support getting and
setting the RSS hash function used by the device.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.

It modifies drivers implementation of set/get_rxfh accordingly.

This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.

User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.

Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.

Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

since head->handle == handle (checked before), just assign handle.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

rcu variant is not correct here. The code is called by updater (rtnl
lock is held), not by reader (no rcu_read_lock is held).
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

rcu variant is not correct here. The code is called by updater (rtnl
lock is held), not by reader (no rcu_read_lock is held).
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
ACKed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-12-06

This series contains updates to i40e and i40evf.

Shannon provides several patches to cleanup and fix i40e.  First removes
an unneeded break statement in i40e_vsi_link_event().  Then removes
some debug messages that really do not give any useful information and
ends up getting printed every service_task loop, which fills the logfile
with noise when AQ tracing is enabled.  Updates the aq_cmd arguments to
use %i which is much more forgiving and user friendly than the more
restrictive %x, or %d.  Fixes the netdev_stat macro, where the old
xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated.
Getting the pf_id from the function number had an issue when
when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal.  This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures.  The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number.

Carolyn adds additional text description for the base pf0 and flow
director generated interrupts, since these interrupts are difficult
to distinguish per port on a multi-function device.

Jacob resolves an issue related to images with multiple PFs per
physical port.  We cannot fully support 1588 PTP features, since only
one port should control (i.e. write) the registers at a time.  Doing
so can cause interference of functionality.

Anjali provides several updates to i40e, first adds the Virtual Channel
OP event opcode for CONFIG_RSS, so that the Virtual Channel state
machine can properly decipher status change events.  Then updates the
driver to add (and use) i40e_is_vf macro for future expansion when new
VF MAC types get added.  Adds new update VSI flow to accommodate a
firmware dix with VSI loopback mode.  All VSIs on a VEB should either
have loopback enabled or disabled, a mixed mode is not supported for a
VEB.  Since our driver supports multiple VSIs per PF that need to talk to
each other make sure to enable Loopback for the PF and FDIR VSI as well.

Mitch provides a couple of i40e and i40evf patches.  First updates
i40evf init code more adept at handling when multiple VFs attempt
to initialize simultaneously.

Joe Perches provides a i40e patch which resolves a compile warning
about about frame size being larger than 2048 bytes by reducing the
stack use by using kmemdup and not using a very large struct on the
stack.

v2:
 - Dropped patch 13 & 14 while Mitch reworks the patches based on
   feedback from Ben Hutchings, probably the tryptophan in the turkey
   is to blame for the delay...
 - Added Joe Perches patch which resolves a compile warning about frame
   size
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
net: Add helper for padding short Ethernet frames

This patch series adds a pair of helpers to pad short Ethernet frames.  The
general idea is to clean up a number of code paths that were all writing
their own versions of the same or similar function.

An added advantage is that this will help to discourage introducing new
bugs as in at least one case I found the skb->len had been updated, but the
tail pointer update was overlooked.

v2: Added skb_put_padto for cases where length is not ETH_ZLEN
    Updated intel drivers and emulex driver to use skb_put_padto
    Updated eth_skb_pad to use skb_put_padto
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace rtl_skb_pad with eth_skb_pad since they do the same thing.

Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update myri10ge to use eth_skb_pad helper.  This also corrects a minor
issue as the driver was updating length without updating the tail pointer.

Cc: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the standard layout for padding an ethernet frame with the
eth_skb_pad call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.

Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds two new helper functions skb_put_padto and eth_skb_pad.
These functions deviate from the standard skb_pad or skb_padto in that they
will also update the length and tail pointers so that they reflect the
padding added to the frame.

The eth_skb_pad helper is meant to be used with Ethernet devices to update
either Rx or Tx frames so that they report the correct size.  The
skb_put_padto helper is meant to be used primarily in the transmit path for
network devices that need frames to be padded up to some minimum size and
don't wish to simply update the length somewhere external to the frame.

The motivation behind this is that there are a number of implementations
throughout the network device drivers that are all doing the same thing,
but each a little bit differently and as a result several implementations
contain bugs such as updating the length without updating the tail offset
and other similar issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eli Cohen says:

====================
mlx5 driver updates

The following series contains some fixes to mlx5 as well as update to the list
of supported devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If mlx5_core_create_mkey fails, decrease the pending counter to undo the
previous increment.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Add required __acquire/__release statements to balance spinlock usage.
2. Change the index parameter of begin_wqe() to be unsigned to match supplied
argument type.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ConnectX-4LX to the list of supported devices as well as their virtual
functions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The outbox should be cleared before executing the command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Useful for debugging purposes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These enumerations are not used so remove them.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Command queue descriptor page size is 4KB and not the page size used by the
kernel.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx5 requires at least one interrupt vector for completions so fix the minvec
argument to pci_enable_msix_range() accordingly.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call request module on mlx5_ib so it will be available for applications
requiring it, such as installers that require boot over IB.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chunhao Lin says:

====================
r8169:change hardware setting

This patch series contains two hardware setting modification to prevent
hardware become abnormal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Cmac engine is the bridge between driver and dash firmware.
Other os may not disable cmac when leave. And r8169 did not allocate any
resources for cmac engine. Disable it to prevent abnormal system behavior.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For RTL8168G/GU/H/EP and RTL8411B remove enable tx/rx from its own hw_start
function. This will prevent enable tx/rx before complete hardware tx/rx
setting.

Tx/Rx will be enabled in the end of function rtl_hw_start_8168.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>