- 16 Jan, 2013 14 commits
-
-
Shan Hai authored
commit ce73ec6d upstream. The locking in update_vsyscall_tz() is not only unnecessary because the vdso code copies the data unproteced in __kernel_gettimeofday() but also introduces a hard to reproduce race condition between update_vsyscall() and update_vsyscall_tz(), which causes user space process to loop forever in vdso code. The following patch removes the locking from update_vsyscall_tz(). Locking is not only unnecessary because the vdso code copies the data unprotected in __kernel_gettimeofday() but also erroneous because updating the tb_update_count is not atomic and introduces a hard to reproduce race condition between update_vsyscall() and update_vsyscall_tz(), which further causes user space process to loop forever in vdso code. The below scenario describes the race condition, x==0 Boot CPU other CPU proc_P: x==0 timer interrupt update_vsyscall x==1 x++;sync settimeofday update_vsyscall_tz x==2 x++;sync x==3 sync;x++ sync;x++ proc_P: x==3 (loops until x becomes even) Because the ++ operator would be implemented as three instructions and not atomic on powerpc. A similar change was made for x86 in commit 6c260d58 ("x86: vdso: Remove bogus locking in update_vsyscall_tz") Signed-off-by:
Shan Hai <shan.hai@windriver.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Christian Lamparter authored
commit 4010fe21 upstream. This patch adds USBIDs for: - DrayTek Vigor 530 - Zoom 4410a It also adds a note about Gemtek WUBI-100GW and SparkLAN WL-682 USBID conflict [WUBI-100GW is a ISL3886+NET2280 (LM86 firmare) solution, whereas WL-682 is a ISL3887 (LM87 firmware)] device. Source: <http://www.wikidevi.com/wiki/Intersil/p54/usb/windows> Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Sujith Manoharan authored
commit a796a1dd upstream. Populate iniModesRxGain with the correct initvals array for AR9485 v1.1 Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Tomasz Guszkowski authored
commit 3194b7fc upstream. Added USB ID for T-Com Sinus 154 data II. Signed-off-by:
Tomasz Guszkowski <tsg@o2.pl> Acked-by:
-
Hugh Dickins authored
commit f2a07f40 upstream. Recently I suggested using "mount -o remount,mpol=local /tmp" in NUMA mempolicy testing. Very nasty. Reading /proc/mounts, /proc/pid/mounts or /proc/pid/mountinfo may then corrupt one bit of kernel memory, often in a page table (causing "Bad swap" or "Bad page map" warning or "Bad pagetable" oops), sometimes in a vm_area_struct or rbnode or somewhere worse. "mpol=prefer" and "mpol=prefer:Node" are equally toxic. Recent NUMA enhancements are not to blame: this dates back to 2.6.35, when commit e17f74af "mempolicy: don't call mpol_set_nodemask() when no_context" skipped mpol_parse_str()'s call to mpol_set_nodemask(), which used to initialize v.preferred_node, or set MPOL_F_LOCAL in flags. With slab poisoning, you can then rely on mpol_to_str() to set the bit for node 0x6b6b, probably in the next page above the caller's stack. mpol_parse_str() is only called from shmem_parse_options(): no_context is always true, so call it unused for now, and remove !no_context code. Set v.nodes or v.preferred_node or MPOL_F_LOCAL as mpol_to_str() might expect. Then mpol_to_str() can ignore its no_context argument also, the mpol being appropriately initialized whether contextualized or not. Rename its no_context unused too, and let subsequent patch remove them (that's not needed for stable backporting, which would involve rejects). I don't understand why MPOL_LOCAL is described as a pseudo-policy: it's a reasonable policy which suffers from a confusing implementation in terms of MPOL_PREFERRED with MPOL_F_LOCAL. I believe this would be much more robust if MPOL_LOCAL were recognized in switch statements throughout, MPOL_F_LOCAL deleted, and MPOL_PREFERRED use the (possibly empty) nodes mask like everyone else, instead of its preferred_node variant (I presume an optimization from the days before MPOL_LOCAL). But that would take me too long to get right and fully tested. Signed-off-by:
Hugh Dickins <hughd@google.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jeff Layton authored
commit 31efee60 upstream. When a call goes out, the signing code adjusts the sequence number upward by two to account for the request and the response. An NT_CANCEL however doesn't get a response of its own, it just hurries the server along to get it to respond to the original request more quickly. Therefore, we must adjust the sequence number back down by one after signing a NT_CANCEL request. Reported-by:
Tim Perry <tdparmor-sambabugs@yahoo.com> Signed-off-by:
Jeff Layton <jlayton@redhat.com> Signed-off-by:
Steve French <smfrench@gmail.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Christoffer Dall authored
commit ad4b3fb7 upstream. Unfortunately with !CONFIG_PAGEFLAGS_EXTENDED, (!PageHead) is false, and (PageHead) is true, for tail pages. If this is indeed the intended behavior, which I doubt because it breaks cache cleaning on some ARM systems, then the nomenclature is highly problematic. This patch makes sure PageHead is only true for head pages and PageTail is only true for tail pages, and neither is true for non-compound pages. [ This buglet seems ancient - seems to have been introduced back in Apr 2008 in commit 6a1e7f77: "pageflags: convert to the use of new macros". And the reason nobody noticed is because the PageHead() tests are almost all about just sanity-checking, and only used on pages that are actual page heads. The fact that the old code returned true for tail pages too was thus not really noticeable. - Linus ] Signed-off-by:
Christoffer Dall <cdall@cs.columbia.edu> Acked-by:
Andrea Arcangeli <aarcange@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Will Deacon <Will.Deacon@arm.com> Cc: Steve Capper <Steve.Capper@arm.com> Cc: Christoph Lameter <cl@linux.com> Signed-off-by:
-
Andy Lutomirski authored
commit 812089e0 upstream. Otherwise it fails like this on cards like the Transcend 16GB SDHC card: mmc0: new SDHC card at address b368 mmcblk0: mmc0:b368 SDC 15.0 GiB mmcblk0: error -110 sending status command, retrying mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb0 Tested on my Lenovo x200 laptop. [bhelgaas: changelog] Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Chris Ball <cjb@laptop.org> CC: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by:
-
Michael Tokarev authored
commit d096ad0f upstream. When a journal-less ext4 filesystem is mounted on a read-only block device (blockdev --setro will do), each remount (for other, unrelated, flags, like suid=>nosuid etc) results in a series of scary messages from kernel telling about I/O errors on the device. This is becauese of the following code ext4_remount(): if (sbi->s_journal == NULL) ext4_commit_super(sb, 1); at the end of remount procedure, which forces writing (flushing) of a superblock regardless whenever it is dirty or not, if the filesystem is readonly or not, and whenever the device itself is readonly or not. We only need call ext4_commit_super when the file system had been previously mounted read/write. Thanks to Eric Sandeen for help in diagnosing this issue. Signed-off-By:
Michael Tokarev <mjt@tls.msk.ru> Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Signed-off-by:
-
Chris Verges authored
commit 0602934f upstream. If an LM73 device does not exist on an I2C bus, attempts to communicate with the device result in an error code returned from the i2c read/write functions. The current lm73 driver casts that return value from a s32 type to a s16 type, then converts it to a temperature in celsius. Because negative temperatures are valid, it is difficult to distinguish between an error code printed to the response buffer and a negative temperature recorded by the sensor. The solution is to evaluate the return value from the i2c functions before performing any temperature calculations. If the i2c function did not succeed, the error code should be passed back through the virtual file system layer instead of being printed into the response buffer. Before: $ cat /sys/class/hwmon/hwmon0/device/temp1_input -46 After: $ cat /sys/class/hwmon/hwmon0/device/temp1_input cat: read error: No such device or address Signed-off-by:
Chris Verges <kg4ysn@gmail.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Jan Kara authored
commit d7961c7f upstream. The following race is possible between start_this_handle() and someone calling jbd2_journal_flush(). Process A Process B start_this_handle(). if (journal->j_barrier_count) # false if (!journal->j_running_transaction) { #true read_unlock(&journal->j_state_lock); jbd2_journal_lock_updates() jbd2_journal_flush() write_lock(&journal->j_state_lock); if (journal->j_running_transaction) { # false ... wait for committing trans ... write_unlock(&journal->j_state_lock); ... write_lock(&journal->j_state_lock); if (!journal->j_running_transaction) { # true jbd2_get_transaction(journal, new_transaction); write_unlock(&journal->j_state_lock); goto repeat; # eventually blocks on j_barrier_count > 0 ... J_ASSERT(!journal->j_running_transaction); # fails We fix the race by rechecking j_barrier_count after reacquiring j_state_lock in exclusive mode. Reported-by: yjwsignal@empal.com Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Jan Kara authored
commit 261cb20c upstream. Currently we allow enabling dioread_nolock mount option on remount for filesystems where blocksize < PAGE_CACHE_SIZE. This isn't really supported so fix the bug by moving the check for blocksize != PAGE_CACHE_SIZE into parse_options(). Change the original PAGE_SIZE to PAGE_CACHE_SIZE along the way because that's what we are really interested in. Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Signed-off-by:
-
Krzysztof Mazur authored
commit 0fde901f upstream. Some broken systems (like HP nc6120) in some cases, usually after LID close/open, enable VGA plane, making display unusable (black screen on LVDS, some strange mode on VGA output). We used to disable VGA plane only once at startup. Now we also check, if VGA plane is still disabled while changing mode, and fix that if something changed it. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57434Signed-off-by:
Krzysztof Mazur <krzysiek@podlesie.net> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> [bwh: Backported to 3.2: intel_modeset_setup_hw_state() does not exist, so call i915_redisable_vga() directly from intel_lid_notify()] Signed-off-by:
-
Forrest Liu authored
commit c36575e6 upstream. When depth of extent tree is greater than 1, logical start value of interior node is not correctly updated in ext4_ext_rm_idx. Signed-off-by:
Forrest Liu <forrestl@synology.com> Signed-off-by:
Ashish Sangwan <ashishsangwan2@gmail.com> Signed-off-by:
-
- 03 Jan, 2013 26 commits
-
-
Ben Hutchings authored
-
Marco Stornelli authored
commit fdb59507 upstream. The return value of rounddown_pow_of_two wasn't evaluated, so the operation was a no-op. Signed-off-by:
Marco Stornelli <marco.stornelli@gmail.com> Reported-by:
Andrew Morton <akpm@linux-foundation.org> Reviewed-by:
WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by:
-
Malcolm Priestley authored
commit 70e22779 upstream. The timer appears to run too fast/race on 64 bit systems. Using msecs_to_jiffies seems to cause a deadlock on 64 bit. A calculation of (MSecond * HZ) / 1000 appears to run satisfactory. Change BSSIDInfoCount to u32. After this patch the driver can be successfully connect on little endian 64/32 bit systems. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Malcolm Priestley authored
commit c0d05b30 upstream. Fixes long issues. Signed-off-by:
-
Malcolm Priestley authored
commit b4dc03af upstream. Fixes long warning messages from patch [PATCH 08/14] staging: vt6656: 64 bit fixes : correct all type sizes Signed-off-by:
-
Malcolm Priestley authored
commit 77304928 upstream. After this patch all BYTE/WORD/DWORD types can be replaced with the appropriate u sizes. Signed-off-by:
-
Malcolm Priestley authored
commit a552397d upstream. Size of long issues replace with u32. Signed-off-by:
-
Malcolm Priestley authored
commit ab1dd996 upstream. Calling RFbSetPower with uCH zero value will cause out of bound array reference. This causes 64 bit kernels to oops on boot. Note: Driver does not function on 64 bit kernels and should be blacklisted on them. Signed-off-by:
-
Namjae Jeon authored
commit 2fb7d99d upstream. Need to brelse the buffer_head stored in cur_epos and next_epos. Signed-off-by:
Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by:
Ashish Sangwan <a.sangwan@samsung.com> Signed-off-by:
-
David Rientjes authored
commit 1f1d06c3 upstream. On COW, a new hugepage is allocated and charged to the memcg. If the system is oom or the charge to the memcg fails, however, the fault handler will return VM_FAULT_OOM which results in an oom kill. Instead, it's possible to fallback to splitting the hugepage so that the COW results only in an order-0 page being allocated and charged to the memcg which has a higher liklihood to succeed. This is expensive because the hugepage must be split in the page fault handler, but it is much better than unnecessarily oom killing a process. Signed-off-by:
David Rientjes <rientjes@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Johannes Weiner <jweiner@redhat.com> Acked-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by:
-
Ben Hutchings authored
This reverts commit 39d18dc4 which was commit 60cefed4 upstream. This was not needed and is not suitable for 3.2.y. Reported-by:
Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
-
Mike Miller authored
commit fe0c9610 upstream. Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 47969684 upstream. The driver has only 4 hardcoded labels, but allows much more memory. Fix it by removing the hardcoded logic, using snprintf() instead. [ 19.833972] general protection fault: 0000 [#1] SMP [ 19.837733] Modules linked in: i82975x_edac(+) edac_core firewire_ohci firewire_core crc_itu_t nouveau mxm_wmi wmi video i2c_algo_bit drm_kms_helper ttm drm i2c_core [ 19.837733] CPU 0 [ 19.837733] Pid: 390, comm: udevd Not tainted 3.6.1-1.fc17.x86_64.debug #1 Dell Inc. Precision WorkStation 390 /0MY510 [ 19.837733] RIP: 0010:[<ffffffff813463a8>] [<ffffffff813463a8>] strncpy+0x18/0x30 [ 19.837733] RSP: 0018:ffff880078535b68 EFLAGS: 00010202 [ 19.837733] RAX: ffff880069fa9708 RBX: ffff880078588000 RCX: ffff880069fa9708 [ 19.837733] RDX: 000000000000001f RSI: 5f706f5f63616465 RDI: ffff880069fa9708 [ 19.837733] RBP: ffff880078535b68 R08: ffff880069fa9727 R09: 000000000000fffe [ 19.837733] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000003 [ 19.837733] R13: 0000000000000000 R14: ffff880069fa9290 R15: ffff880079624a80 [ 19.837733] FS: 00007f3de01ee840(0000) GS:ffff88007c400000(0000) knlGS:0000000000000000 [ 19.837733] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 19.837733] CR2: 00007f3de00b9000 CR3: 0000000078dbc000 CR4: 00000000000007f0 [ 19.837733] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 19.837733] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 19.837733] Process udevd (pid: 390, threadinfo ffff880078534000, task ffff880079642450) [ 19.837733] Stack: [ 19.837733] ffff880078535c18 ffffffffa017c6b8 00040000816d627f ffff880079624a88 [ 19.837733] ffffc90004cd6000 ffff880079624520 ffff88007ac21148 0000000000000000 [ 19.837733] 0000000000000000 0004000000000000 feda000078535bc8 ffffffff810d696d [ 19.837733] Call Trace: [ 19.837733] [<ffffffffa017c6b8>] i82975x_init_one+0x2e6/0x3e6 [i82975x_edac] ... Fix bug reported at: https://bugzilla.redhat.com/show_bug.cgi?id=848149 And, very likely: https://bbs.archlinux.org/viewtopic.php?id=148033 https://bugzilla.kernel.org/show_bug.cgi?id=47171 Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> [bwh: Backported to 3.2: - Adjust context - Use csrow->channels[chan].label not csrow->channels[chan]->dimm->label] Signed-off-by:
-
Dan Carpenter authored
[Not needed in 3.8 or newer as this driver is removed there. - gregkh] We get this from user space and nothing has been done to ensure that these strings are NUL terminated. Reported-by:
Chen Gang <gang.chen@asianux.com> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Jiri Slaby authored
commit bcdee04e upstream. pci_disable_device(pdev) used to be in pci remove function. But this PCI device has two functions with interrupt lines connected to a single pin. The other one is a USB host controller. So when we disable the PIN there e.g. by rmmod hpilo, the controller stops working. It is because the interrupt link is disabled in ACPI since it is not refcounted yet. See acpi_pci_link_free_irq called from acpi_pci_irq_disable. It is not the best solution whatsoever, but as a workaround until the ACPI irq link refcounting is sorted out this should fix the reported errors. References: https://lkml.org/lkml/2008/11/4/535Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Grant Grundler <grundler@parisc-linux.org> Cc: Nobin Mathew <nobin.mathew@gmail.com> Cc: Robert Hancock <hancockr@shaw.ca> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Altobelli <david.altobelli@hp.com> Signed-off-by:
-
Johannes Berg authored
commit 7c341582 upstream. The RX replenish code doesn't handle DMA mapping failures, which will cause issues if there actually is a failure. This was reported by Shuah Khan who found a DMA mapping framework warning ("device driver failed to check map error"). Reported-by:
Shuah Khan <shuah.khan@hp.com> Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [bwh: Backported to 3.2: - Adjust filename, context, indentation - Use bus(trans) instead of trans where necessary - Use hw_params(trans).rx_page_order instead of trans_pcie->rx_page_order] Signed-off-by:
-
Jay Purohit authored
[ Upstream commit af1b85e4 ] I noticed that the iPhone ethernet driver did not support iPhone 5. I quickly added support to it in my kernel, here's a patch. Signed-off-by:
Jay Purohit <jspurohit@velocitylimitless.com> Acked-by:
Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by:
Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Johannes Berg authored
[ Upstream commit 1bf3751e ] ip_check_defrag() might be called from af_packet within the RX path where shared SKBs are used, so it must not modify the input SKB before it has unshared it for defragmentation. Use skb_copy_bits() to get the IP header and only pull in everything later. The same is true for the other caller in macvlan as it is called from dev->rx_handler which can also get a shared SKB. Reported-by:
Eric Leblond <eric@regit.org> Signed-off-by:
-
Alexander Shiyan authored
[ Upstream commit 2355a62b ] Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Alan Cox authored
[ Upstream commit da9da01d ] Without this udev doesn't have a way to key the ne device to the platform device. Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Tommi Rantala authored
[ Upstream commit 6e51fe75 ] Consider the following program, that sets the second argument to the sendto() syscall incorrectly: #include <string.h> #include <arpa/inet.h> #include <sys/socket.h> int main(void) { int fd; struct sockaddr_in sa; fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/); if (fd < 0) return 1; memset(&sa, 0, sizeof(sa)); sa.sin_family = AF_INET; sa.sin_addr.s_addr = inet_addr("127.0.0.1"); sa.sin_port = htons(11111); sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa)); return 0; } We get -ENOMEM: $ strace -e sendto ./demo sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 ENOMEM (Cannot allocate memory) Propagate the error code from sctp_user_addto_chunk(), so that we will tell user space what actually went wrong: $ strace -e sendto ./demo sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 EFAULT (Bad address) Noticed while running Trinity (the syscall fuzzer). Signed-off-by:
Tommi Rantala <tt.rantala@gmail.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Tommi Rantala authored
[ Upstream commit be364c8c ] Trinity (the syscall fuzzer) discovered a memory leak in SCTP, reproducible e.g. with the sendto() syscall by passing invalid user space pointer in the second argument: #include <string.h> #include <arpa/inet.h> #include <sys/socket.h> int main(void) { int fd; struct sockaddr_in sa; fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/); if (fd < 0) return 1; memset(&sa, 0, sizeof(sa)); sa.sin_family = AF_INET; sa.sin_addr.s_addr = inet_addr("127.0.0.1"); sa.sin_port = htons(11111); sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa)); return 0; } As far as I can tell, the leak has been around since ~2003. Signed-off-by:
-
nikolay@redhat.com authored
[ Upstream commit e196c0e5 ] Race between bonding_store_slaves_active() and slave manipulation functions. The bond_for_each_slave use in bonding_store_slaves_active() is not protected by any synchronization mechanism. NULL pointer dereference is easy to reach. Fixed by acquiring the bond->lock for the slave walk. v2: Make description text < 75 columns Signed-off-by:
Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by:
Jay Vosburgh <fubar@us.ibm.com> Signed-off-by:
-
Sarveshwar Bandi authored
[ Upstream commit 0e376bd0 ] Patch sets the lowest gso_max_size and gso_max_segs values of the slave devices during enslave and detach. Signed-off-by:
Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Herton Ronaldo Krzesinski authored
[ no commit upstream, since usb_alloc_coherent usage was removed from the driver before this was fixed ] Commit cafbe85f ("USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core") introduced a regression: it changed the size used in usb_alloc_coherent, but failed to do the same for the usb_free_coherent calls. It also was marked for stable and got backported to older kernels. But in the upstream kernel, the usage of usb_alloc_coherent was right after removed from the driver, so upstream doesn't have this problem, while the stable kernels still have, and thus need this fix. BugLink: https://bugs.launchpad.net/bugs/1074157Signed-off-by:
Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by:
-
Jani Nikula authored
commit 9a30a61f upstream. commit 500a8cc4 Author: Zhenyu Wang <zhenyuw@linux.intel.com> Date: Wed Jan 13 11:19:52 2010 +0800 drm/i915: parse eDP panel color depth from VBT block originally introduced parsing bpp for eDP from VBT, with a default of 18 bpp if the eDP BIOS data block is not present. Turns out that default seems to break the Macbook Pro with retina display, as noted in commit 4344b813 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Fri Aug 10 11:10:20 2012 +0200 drm/i915: ignore eDP bpc settings from vbt Since we can't ignore bpc settings from VBT completely after all, get rid of the default. Do not clamp eDP to 18 bpp by default if the eDP BDB is missing from VBT. Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Tested-by:
Henrik Rydberg <rydberg@euromail.se> [danvet: paste in the updated commit message from irc.] Signed-off-by:
-
