- 05 Mar, 2012 4 commits
-
-
Felix Fietkau authored
Not doing so could cause the tx status queue to overflow during longer periods of time without non-beacon tx. These events are also required for proper drv_tx_last_beacon handling. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
Since AR9003 uses a global tx status queue, processing tx status outside of the regular tx tasklet is dangerous and messes up hardware/software synchronization of tx status events. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Felix Fietkau authored
The approach of this change is flawed, as it triggers tx status processing from more callsites, yet the chips only have one global tx status queue. Subsequent patches will properly fix the issue that this one tried to address. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
When authentication type is configured to NL80211_AUTHTYPE_AUTOMATIC, driver tries to connect using open mode. The association is failed if AP is configured in shared mode. This patch adds code to try association using shared mode as well if open mode association fails. Now since we returned exact error code in association response handler (instead of -1), corresponding changes are done in mwifiex_process_cmdresp(). Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 29 Feb, 2012 19 commits
-
-
John W. Linville authored
That commit intended for 3.4 renamed IEEE80211_TX_CTL_POLL_RESPONSE as IEEE80211_TX_CTL_NO_PS_BUFFER. Meanwhile, "carl9170: fix frame delivery if sta is in powersave mode" added a reference to IEEE80211_TX_CTL_POLL_RESPONSE in the fixes stream for 3.3. This simple patch fixes that merge boo-boo. Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Zefir Kurtisi authored
Previous RX error checking was done exclusive-or for different error types and caused DFS pulse events to be dropped when other error flags (e.g. CRC) were set simultaneously. This patch decouples PHY error processing from other types and ensures that all pulses detected by HW are accounted by the pattern detector. Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Greg Dietsche authored
Remove the enum il4965_calib_enabled_state because it is not used. Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Greg Dietsche authored
Remove the enum il_calib. It defined one identifier: IL_CALIB_MAX. Remove the function il4965_calib_free_results. It was doing nothing because IL_CALIB_MAX is zero. Next, remove calib_results from the il_priv structure and also remove the associated return type/struct il_calib_result. Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Greg Dietsche authored
Since the menuconfig system doesn't indent the debug options for the 3945 /4965, add some text to make it clear which debug options are being configured. Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Greg Dietsche authored
Move the debug options so they appear below the 3945 / 4965 options. Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
This renames the IEEE80211_TX_CTL_POLL_RESPONSE TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also uses it for non-bufferable MMPDUs (all MMPDUs but deauth, disassoc and action frames.) Previously, mac80211 would let the MMPDU through but not set the flag so drivers supporting some hardware aids for avoiding the PS races would then reject the frame. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
Instead of defining an 'enum', we can simply use 'u8' flag for WEP status. Rename 'wep_status' to 'wep_enabled' to match with 'wpa_enabled' and 'wpa2_enabled'. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
It should have been removed by commit "mwifiex: use cfg80211 dynamic scan..." (7c6fa2a8..) after adding code to avoid an extra scan during association because scan entries are valid for 15 seconds in cfg80211 stack. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The association sequence looks (roughly) like this now: * set BSSID * set station to EXIST state * send auth * set station to AUTH state * send assoc * set station to ASSOC state * set BSS info to associated In contrast, the deauth/disassoc sequence is the other way around: * clear BSSID/BSS info state * remove station * send deauth/disassoc (in some cases the last two steps are reversed.) This patch encodes the entire sequence in the ieee80211_set_disassoc() function and changes it to be like this, for good measure with an explicit flush: * send deauth/disassoc * flush * remove station * clear BSSID/BSS info state At least iwlwifi gets confused with the other sequence in P2P mode and complains that it wasn't able to flush the queues. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
When ieee80211_set_disassoc() is called with the tx argument set to true, it will send DelBA out to the peer. This isn't useful or necessary in a few cases where we do it today, those being when we lost the connection or when the supplicant explicitly asked us to not tell the AP. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc() pass out the frame and call it from the caller. That saves the SKB allocation if we don't actually want to send the frame and enables us to make the ordering smarter in the future. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
In "cfg80211: no cookies in cfg80211_send_XXX()" Holger Schurig removed the cookies in the calls from mac80211 to cfg80211, but the ones in the other direction were left in. Remove them now. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stanislav Yakovlev authored
It's just a duplicate of ipw2100_bg_rates[]. Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Florian Fainelli authored
I am running Debian testing kernel 3.1.0-1-amd64, using a 079b:0062 Sagem XG-76NA 802.11bg stick. Upon zd1211rw interface bringup (ifconfig wlan0 up) I get the following timeout: [ 950.330573] zd1211rw 1-3:1.0: phy2 [ 955.108510] zd1211rw 1-3:1.0: firmware version 4725 [ 955.148532] zd1211rw 1-3:1.0: zd1211b chip 079b:0062 v4810 high 00-19-70 AL2230_RF pa0 g--NS [snip] [ 955.204072] zd1211rw 1-3:1.0: error ioread32(CR_REG1): -110 A second ifconfig wlan0 up brings the interface up without problems. After a bit more debugging, the call trace is the following: [10241.028130] zd1211rw 1-3:1.0: zd_chip_lock_phy_regs: error ioread32(CR_REG1): -110 [10241.028140] zd1211rw 1-3:1.0: zd_switch_radio_on: failed to lock PHY regs [10241.028148] zd1211rw 1-3:1.0: zd_op_start: failed to set radio on Adding a 10 milliseconds delay between the call to set_mc_hash() and zd_chip_switch_radio_on() allows successful interface bringups in all cases and matches what the vendor driver did. Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
Recent commit "mwifiex: clear previous security setting during association" fixes association failure problems observed in some corner cases by clearing previous security setting before each association. We should reset encryption mode flag as well. This patch takes care of it. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Christian Lamparter authored
Nicolas Cavallari discovered that carl9170 has some serious problems delivering data to sleeping stations. It turns out that the driver was not honoring two important flags (IEEE80211_TX_CTL_POLL_RESPONSE and IEEE80211_TX_CTL_CLEAR_PS_FILT) which are set on frames that should be sent although the receiving station is still in powersave mode. Cc: stable <stable@vger.kernel.org> Reported-by: Nicolas Cavallari <Nicolas.Cavallari@lri.fr> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Nicolas Cavallari authored
On Access Point mode, when transmitting a packet, if the destination station is in powersave mode, we abort transmitting the packet to the device queue, but we do not reclaim the allocated memory. Given enough packets, we can go in a state where there is no packet on the device queue, but we think the device has no memory left, so no packet gets transmitted, connections breaks and the AP stops working. This undo the allocation done in the TX path when the station is in power-save mode. Signed-off-by: Nicolas Cavallari <cavallar@lri.fr> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 27 Feb, 2012 17 commits
-
-
Emmanuel Grumbach authored
This is a fixup for my: iwlwifi: kill iwl_bus.h Please fold them into one patch for upstream Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Wey-Yi Guy authored
Update the pci subsystem id and product name for 6005 series devices Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Wey-Yi Guy authored
Add new sku to 6x35 series Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
We can use forward declaration for the relevant struct since they aren't dereferenced in the header file. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Also add a might_sleep to enforce the context requirements. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
It is op_mode related Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
It is op_mode related Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
No one needs it any more Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This is temporary, but at least we can now throw the bus away and move the iwl_pci_{probe,remove} functions. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
They don't need to be in iwl-dev.h Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
The transport should not dereference the iwl_priv pointer. Remove a few of those. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Export it as "nic_error" notification, the error handling will be in the op_mode. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Export it as "hw_rf_kill" notification. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Export them as "queue_full" and "queue_not_full" notification. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This is the op_mode's Rx handler. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
This handler allows the transport layer to free an skb from the op_mode. This can happen when the driver is stopped while Tx packets are pending in the transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Emmanuel Grumbach authored
Sparse prefers __aligned(sizeof(void *)); Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
-