ISO 11898-1 specifies in section 11.3.3 "Transmitter delay
compensation" that "the configuration range for [the] SSP position
shall be at least 0 to 63 minimum time quanta."

Because SSP = TDCV + TDCO, it means that we should allow both TDCV and
TDCO to hold zero value in order to honor SSP's minimum possible
value.

However, current implementation assigned special meaning to TDCV and
TDCO's zero values:
  * TDCV = 0 -> TDCV is automatically measured by the transceiver.
  * TDCO = 0 -> TDC is off.

In order to allow for those values to really be zero and to maintain
current features, we introduce two new flags:
  * CAN_CTRLMODE_TDC_AUTO indicates that the controller support
    automatic measurement of TDCV.
  * CAN_CTRLMODE_TDC_MANUAL indicates that the controller support
    manual configuration of TDCV. N.B.: current implementation failed
    to provide an option for the driver to indicate that only manual
    mode was supported.

TDC is disabled if both CAN_CTRLMODE_TDC_AUTO and
CAN_CTRLMODE_TDC_MANUAL flags are off, c.f. the helper function
can_tdc_is_enabled() which is also introduced in this patch.

Also, this patch adds three fields: tdcv_min, tdco_min and tdcf_min to
struct can_tdc_const. While we are not convinced that those three
fields could be anything else than zero, we can imagine that some
controllers might specify a lower bound on these. Thus, those minimums
are really added "just in case".

Comments of struct can_tdc and can_tdc_const are updated accordingly.

Finally, the changes are applied to the etas_es58x driver.

Link: https://lore.kernel.org/all/20210918095637.20108-2-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

All timing calculation is done with unsigned integers, so change type
of tseg1 and alltseg to unsigned int, too.

Link: https://lore.kernel.org/all/20211013130653.1513627-1-mkl@pengutronix.de
Link: https://github.com/linux-can/can-utils/pull/314Reported-by: Gary Bisson <bisson.gary@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

hrtimer_forward_now() provides the same functionality as the open coded
hrimer_forward() invocation. Prepares for removal of hrtimer_forward() from
the public interfaces.

Link: https://lore.kernel.org/all/20210923153339.684546907@linutronix.deSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-can@vger.kernel.org
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: netdev@vger.kernel.org
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This allows explicitly specifying which children are present on the mdio
bus. Additionally, it allows for non-phy MDIO devices on the bus.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds an optional mdio bus child node. If present, the mac will
look for PHYs there instead of directly under the top-level node. This
eliminates any ambiguity about whether child nodes are PHYs, and allows
the MDIO bus to contain non-PHY devices.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 16nm internal EPHY that is present in 7712 is actually a 16nm
Gigabit PHY which has been forced to operate in 10/100 mode. Its
controls are therefore via the EXT_GPHY_CTRL registers and not via the
EXT_EPHY_CTRL which are used for all GENETv5 adapters. Add a match on
the 7712 compatible string to allow that differentiation to happen.

On previous GENETv4 chips the EXT_CFG_IDDQ_GLOBAL_PWR bit was cleared by
default, but this is not the case with this chip, so we need to make
sure we clear it to power on the EPHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

7712 includes a GENETv5 adapter with an on-chip 10/100 16nm Ethernet PHY
which requires us to document that controller's integration specifically
for proper driver keying.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

7712 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
utilize the recently defined 16nm EPHY macro to configure that PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This converts users of mdiobus to mdiodev using the following semantic
patch:

@@
identifier mdiodev;
expression regnum;
@@

- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)

@@
identifier mdiodev;
expression regnum, val;
@@

- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This refactors the phylink pcs helper functions to use mdiobus_* instead
of mdiodev_*.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds some helpers for accessing non-phy MDIO devices. They are
analogous to phy_(read|write|modify), except that they take an mdio_device
and not a phy_device.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

With current KPU profile, we have 2 reserved entries which can
be loaded from firmware to parse custom headers. Adding changes
to increase these reserved entries to 6.
And also removed KPU entries for unused LTYPEs like
NPC_LT_LA_IH_8_ETHER, NPC_LT_LA_IH_4_ETHER, NPC_LT_LA_IH_2_ETHER
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
Delete impossible devlink notifications

This series is a followup to the delayed devlink notification scheme.

I removed the impossible notifications together with attempt to annotate
various calls in order to mark them as pre/post devlink_register().

Other notifications are called before and after delvink_register() so
they weren't changed in this pathcset.
====================

Link: https://lore.kernel.org/r/cover.1634825474.git.leonro@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The parameters are registered before devlink_register() and all the
notifications are delayed. This patch removes not-possible parameters
notifications along with addition of code annotation logic.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The trap logic is registered before devlink_register() and all the
notifications are delayed. This patch removes not-possible trap group
notifications along with addition of code annotation logic.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The trap policer logic is registered before devlink_register() and all the
notifications are delayed. This patch removes not-possible notifications
along with addition of code annotation logic.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The change of devlink_register() to be last devlink command together
with delayed notification logic made the publish API to be obsolete.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When addr_gen_mode is set to IN6_ADDR_GEN_MODE_NONE, the link-local addr
should not be generated. But it isn't the case for GRE (as well as GRE6)
and SIT tunnels. Make it so that tunnels consider the addr_gen_mode,
especially for IN6_ADDR_GEN_MODE_NONE.

Do this in add_v4_addrs() to cover both GRE and SIT only if the addr
scope is link.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Link: https://lore.kernel.org/r/20211020200618.467342-1-ssuryaextr@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix following coccicheck warning:
./drivers/net/dsa/sja1105/sja1105_main.c:1193:1-33: WARNING: Function
for_each_available_child_of_node should have of_node_put() before return.

Early exits from for_each_available_child_of_node should decrement the
node reference counter.

Fixes: 9ca482a2 ("net: dsa: sja1105: parse {rx, tx}-internal-delay-ps properties for RGMII delays")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211021094606.7118-1-wanjiabing@vivo.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Repalce kthread_create/wake_up_process() with kthread_run()
to simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211021084158.2183-1-caihuoqing@baidu.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-drivers-next-2021-10-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.16

Second set of patches for v5.16 and this time we have a big one. We
have the new Realtek driver rtw89 with over 90 kLOC and also over 150
patches for mt76. ath9k also got few new small features. And the usual
cleanups and fixes all over.

Major changes:

rtw89
 * new Realtek 802.11ax driver
 * supports Realtek 8852AE 802.11ax 2x2 chip

ath9k
 * add option to reset the wifi chip via debugfs
 * convert Device Tree bindings to the json-schema
 * support Device Tree ieee80211-freq-limit property to limit channels

mt76
 * mt7921 aspm support
 * mt7921 testmode support
 * mt7915 LED support
 * mt7921 6GHz band support
 * support for eeprom data in DT
 * mt7915 TWT support
 * mt7921s SDIO support

* tag 'wireless-drivers-next-2021-10-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (213 commits)
  zd1201: use eth_hw_addr_set()
  wl3501_cs: use eth_hw_addr_set()
  ray_cs: use eth_hw_addr_set()
  ...
====================

Link: https://lore.kernel.org/r/20211022075845.0E679C4360D@smtp.codeaurora.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Quite a few changes:
 * the applicable eth_hw_addr_set() and const hw_addr changes
 * various code cleanups/refactorings
 * stack usage reductions across the wireless stack
 * some unstructured find_ie() -> structured find_element()
   changes
 * a few more pieces of multi-BSSID support
 * some 6 GHz regulatory support
 * 6 GHz support in hwsim, for testing userspace code
 * Light Communications (LC, 802.11bb) early band definitions
   to be able to add a first driver soon

* tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits)
  cfg80211: fix kernel-doc for MBSSID EMA
  mac80211: Prevent AP probing during suspend
  nl80211: Add LC placeholder band definition to nl80211_band
  ...
====================

Link: https://lore.kernel.org/r/20211021154953.134849-1-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Don't write directly to netdev->dev_addr.

More conversions, mostly in usb/net.

v2: leave out catc (patch 4)

Link: https://lore.kernel.org/r/20211021131214.2032925-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Get these two oldies ready for constant netdev->dev_addr.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Get it ready for constant netdev->dev_addr.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Make sure local references to netdev->dev_addr are constant.
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Get it ready for constant netdev->dev_addr.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Get it ready for constant netdev->dev_addr.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Manually fix all net/usb drivers without separate maintainers.

v2: catc does DMA to the buffer, leave the conversion to Oliver
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Silent merge conflict between these two:

  3d677735 ("net/mlx5: Lag, move lag files into directory")
  14fe2471 ("net/mlx5: Lag, change multipath and bonding to be mutually exclusive")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

M<erge issues...
Signed-off-by: David S. Miller <davem@davemloft.net>

Lots of simnple overlapping additions.

With a build fix from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes from Dave Airlie:
 "Nothing too crazy at the end of the cycle, the kmb modesetting fixes
  are probably a bit large but it's not a major driver, and its fixing
  monitor doesn't turn on type problems.

  Otherwise it's just a few minor patches, one ast regression revert, an
  msm power stability fix.

  ast:
   - fix regression with connector detect

  msm:
   - fix power stability issue

  msxfb:
   - fix crash on unload

  panel:
   - sync fix

  kmb:
   - modesetting fixes"

* tag 'drm-fixes-2021-10-22' of git://anongit.freedesktop.org/drm/drm:
  Revert "drm/ast: Add detect function support"
  drm/kmb: Enable ADV bridge after modeset
  drm/kmb: Corrected typo in handle_lcd_irq
  drm/kmb: Disable change of plane parameters
  drm/kmb: Remove clearing DPHY regs
  drm/kmb: Limit supported mode to 1080p
  drm/kmb: Work around for higher system clock
  drm/panel: ilitek-ili9881c: Fix sync for Feixin K101-IM2BYL02 panel
  drm: mxsfb: Fix NULL pointer dereference crash on unload
  drm/msm/devfreq: Restrict idle clamping to a618 for now

Vladimir Zapolskiy reports:

Commit a7259df7 ("memblock: make memblock_find_in_range method
private") invokes a kernel panic while running kmemleak on OF platforms
with nomaped regions:

  Unable to handle kernel paging request at virtual address fff000021e00000
  [...]
    scan_block+0x64/0x170
    scan_gray_list+0xe8/0x17c
    kmemleak_scan+0x270/0x514
    kmemleak_write+0x34c/0x4ac

The memory allocated from memblock is registered with kmemleak, but if
it is marked MEMBLOCK_NOMAP it won't have linear map entries so an
attempt to scan such areas will fault.

Ideally, memblock_mark_nomap() would inform kmemleak to ignore
MEMBLOCK_NOMAP memory, but it can be called before kmemleak interfaces
operating on physical addresses can use __va() conversion.

Make sure that functions that mark allocated memory as MEMBLOCK_NOMAP
take care of informing kmemleak to ignore such memory.

Link: https://lore.kernel.org/all/8ade5174-b143-d621-8c8e-dc6a1898c6fb@linaro.org
Link: https://lore.kernel.org/all/c30ff0a2-d196-c50d-22f0-bd50696b1205@quicinc.com
Fixes: a7259df7 ("memblock: make memblock_find_in_range method private")
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Tested-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>