Signed-off-by: Hans Petter Selasky <hps@selasky.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

This patch adds a seperate hid-penmount driver to work
around an issue with the HID report descriptor. The
descriptor does not contain the ContactID usage and as
result the touchscreen is represented as normal mouse
to the system.

This driver maps the button 0 emitted by the touchscreen
to BTN_TOUCH. This makes it possible to use touch events
in userspace.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

thingm_remove_rgb() needs to flush the workqueue after all the LED classes
have been unregistered, otherwise the removal might race with another LED
event coming, causing thingm_led_set() to schedule additional work after
thingm_remove_rgb() has flushed it. This obviously causes oops later, as
the scheduled work has been freed in the meantime.

In addition to that, move the hid_hw_stop() to an earlier place, so that
dmesg is not polluted by failure messages about not being able to write
the LED while the device is being shut down.
Reported-and-tested-by: Dylan Alex Simon <dylan-kernel@dylex.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

This patch changes the way usbhid carries out Clear-Halt and reset.

Currently, after a Clear-Halt on the interrupt-IN endpoint, the driver
immediately restarts the interrupt URB, even if the Clear-Halt failed.
This doesn't work out well when the reason for the failure was that
the device was disconnected (when a low- or full-speed device is
connected through a hub to an EHCI controller, transfer errors caused
by disconnection are reported as stalls by the hub).  Instead now the
driver will attempt a reset after a failed Clear-Halt.

The way resets are carried out is also changed.  Now the driver will
call usb_queue_reset_device() instead of calling usb_reset_device()
directly.  This avoids a deadlock that would arise when a device is
unplugged: The hid_reset() routine runs as a workqueue item, a reset
attempt after the device has been unplugged will fail, failure will
cause usbhid to be unbound, and the disconnect routine will try to do
cancel_work_sync().  The usb_queue_reset_device() implementation is
carefully written to handle scenarios like this one properly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Atmel 840B digitizer presents a stylus interface which reports twice
the X coordinate and then twice the Y coordinate. In its current
implementation, hid-input assign the first X to X, then the second to Y,
then the first Y to Z, then the second one to RX.

This is wrong, and X should always be mapped to X, no matter what.
A solution consists in forcing X, Y, Z, RX, RY, RZ to be mapped to their
correct user space counter part.
Reported-by: Éric Brunet <Eric.Brunet@lps.ens.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull HID fixes from Jiri Kosina:

 - fixes for a couple potential memory corruption problems (the HW would
   have to be manufactured to be deliberately evil to trigger those)
   found by Ben Hawkes
 - fix for potential infinite loop when using sysfs interface of
   logitech driver, from Simon Wood
 - a couple more simple driver fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: fix a couple of off-by-ones
  HID: logitech: perform bounds checking on device_id early enough
  HID: logitech: fix bounds checking on LED report size
  HID: logitech: Prevent possibility of infinite loop when using /sys interface
  HID: rmi: print an error if F11 is not found instead of stopping the device
  HID: hid-sensor-hub: use devm_ functions consistently
  HID: huion: Use allocated buffer for DMA
  HID: huion: Fail on parameter retrieval errors

Pull sound fixes from Takashi Iwai:
 "A bunch of ASoC fixes with a few HD-audio fixes in this pull request.

  All fairly small, boring and device-specific fixes, in addition to
  MAINTAINERS update for better reviewing"

* tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/hdmi - apply Valleyview fix-ups to Cherryview display codec
  ALSA: hda/hdmi - set depop_delay for haswell plus
  ALSA: hda - restore the gpio led after resume
  ALSA: hda/realtek - Avoid setting wrong COEF on ALC269 & co
  ASoC: pxa-ssp: drop SNDRV_PCM_FMTBIT_S24_LE
  ASoC: fsl-esai: Revert .xlate_tdm_slot_mask() support
  ASoC: mcasp: Fix implicit BLCK divider setting
  ASoC: arizona: Fix TDM slot length handling in arizona_hw_params
  ASoC: pcm512x: Correct Digital Playback control names
  ASoC: dapm: Fix uninitialized variable in snd_soc_dapm_get_enum_double()
  ASoC: Intel: Restore Baytrail ADSP streams only when ADSP was in reset
  ASoC: Intel: Wait Baytrail ADSP boot at resume_early stage
  ASoC: Intel: Merge Baytrail ADSP suspend_noirq into suspend_late
  MAINTAINERS: Add i.MX maintainers and paths to Freescale ASoC entry
  ASoC: Intel: Update Baytrail ADSP firmware name

Pull i2c fixes from Wolfram Sang:
 "Here is the fixup for the 'lowlight' of my last pull request.  I2C is
  not selected anymore by I2C_ACPI.  Instead, the code in question now
  depends on I2C=y.

  Also, Mika has agreed to support me and be the maintainer for I2C-ACPI
  related patches.  Finally, a new-ID-patch came along last week"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: add maintainer for ACPI parts of I2C
  i2c: i801: Add PCI ID for Intel Braswell
  i2c: rework kernel config I2C_ACPI

Pull ia64 update from Tony Luck:
 "Add memfd_create syscall to ia64"

* tag 'please-pull-memfd_create' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  [IA64] Wire up memfd_create() system call

Pull microblaze update from Michal Simek:
 "Wire-up seccomp/getrandom/memfd_create syscalls"

* tag 'microblaze-3.17-rc2' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Wire-up memfd_create syscall
  microblaze: Wire-up getrandom syscall
  microblaze: Wire-up seccomp syscall

There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.

Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.

We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().

Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().

Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The check on report size for REPORT_TYPE_LEDS in logi_dj_ll_raw_request()
is wrong; the current check doesn't make any sense -- the report allocated
by HID core in hid_hw_raw_request() can be much larger than
DJREPORT_SHORT_LENGTH, and currently logi_dj_ll_raw_request() doesn't
handle this properly at all.

Fix the check by actually trimming down the report size properly if it is
too large.

Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add new memfd_create syscall.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add new getrandom syscall.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add new seccomp syscall.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Pull cifs fixes from Steve French:
 "Most important fixes in this set include three SMB3 fixes for stable
  (including fix for possible kernel oops), and a workaround to allow
  writes to Mac servers (only cifs dialect, not more current SMB2.1,
  worked to Mac servers).  Also fallocate support added, and lease fix
  from Jeff"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  [SMB3] Enable fallocate -z support for SMB3 mounts
  enable fallocate punch hole ("fallocate -p") for SMB3
  Incorrect error returned on setting file compressed on SMB2
  CIFS: Fix wrong directory attributes after rename
  CIFS: Fix SMB2 readdir error handling
  [CIFS] Possible null ptr deref in SMB2_tcon
  [CIFS] Workaround MacOS server problem with SMB2.1 write  response
  cifs: handle lease F_UNLCK requests properly
  Cleanup sparse file support by creating worker function for it
  Add sparse file support to SMB2/SMB3 mounts
  Add missing definitions for CIFS File System Attributes
  cifs: remove unused function cifs_oplock_break_wait

Pull filesystem fixes from Jan Kara:
 "udf, isofs, and ext3 bug fixes"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  ext3: Count internal journal as bsddf overhead in ext3_statfs
  isofs: Fix unbounded recursion when processing relocated directories
  udf: avoid unneeded up_write when fail to add entry in ->symlink

Pull x86 platform driver revert from Matthew Garrett:
 "This clearly shouldn't have been merged.  No excuse on my part"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  Revert "platform/x86/toshiba-apci.c possible bad if test?"

Pull KVM fixes from Paolo Bonzini:
 "Reverting a 3.16 patch, fixing two bugs in device assignment (one has
  a CVE), and fixing some problems introduced during the merge window
  (the CMA bug came in via Andrew, the x86 ones via yours truly)"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  virt/kvm/assigned-dev.c: Set 'dev->irq_source_id' to '-1' after free it
  Revert "KVM: x86: Increase the number of fixed MTRR regs to 10"
  KVM: x86: do not check CS.DPL against RPL during task switch
  KVM: x86: Avoid emulating instructions on #UD mistakenly
  PC, KVM, CMA: Fix regression caused by wrong get_order() use
  kvm: iommu: fix the third parameter of kvm_iommu_put_pages (CVE-2014-3601)

Pull SCSI fixes from James Bottomley:
 "These are the two bug fixes I mentioned in the final merge window
  pull.  One is a reversed logic check in the device busy tests which
  can cause a nasty hang and another crash seen in the new SCSI pool
  support if the use count ever goes to zero"

[ The device busy test already got merged from a patch earlier, so is
  now duplicated.  ]

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] save command pool address of Scsi_Host
  [SCSI] fix qemu boot hang problem

This reverts commit bdc3ae72.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

The journal blocks of external journal device should not
be counted as overhead.
Signed-off-by: Chin-Tsung Cheng <chintzung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>

The latest kernel fails to boot qemu arm images when using scsi
for disk access. Boot gets stuck after the following messages.

brd: module loaded
sym53c8xx 0000:00:0c.0: enabling device (0100 -> 0103)
sym0: <895a> rev 0x0 at pci 0000:00:0c.0 irq 93
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi host0: sym-2.2.3

Bisect points to commit 71e75c97 ("scsi: convert device_busy to
atomic_t"). Code inspection shows the following suspicious change
in scsi_request_fn.

out_delay:
-       if (sdev->device_busy == 0 && !scsi_device_blocked(sdev))
+       if (atomic_read(&sdev->device_busy) && !scsi_device_blocked(sdev))
		blk_delay_queue(q, SCSI_QUEUE_DELAY);
	}

'sdev->device_busy == 0' was replaced with 'atomic_read(&sdev->device_busy)',
meaning the logic was reversed. Changing this expression to
'!atomic_read(&sdev->device_busy)' fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We did not check relocated directory in any way when processing Rock
Ridge 'CL' tag. Thus a corrupted isofs image can possibly have a CL
entry pointing to another CL entry leading to possibly unbounded
recursion in kernel code and thus stack overflow or deadlocks (if there
is a loop created from CL entries).

Fix the problem by not allowing CL entry to point to a directory entry
with CL entry (such use makes no good sense anyway) and by checking
whether CL entry doesn't point to itself.

CC: stable@vger.kernel.org
Reported-by: Chris Evans <cevans@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>

We have released the ->i_data_sem before invoking udf_add_entry(),
so in following error path, we should not release this lock again.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>

Mika has done great work in that field, so let people know.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The SMBus host controller is the same as used in Baytrail so add the new
PCI ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Commit da3c6647(I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI
config) adds a new kernel config I2C_ACPI and make I2C core built in
when the config is selected. This is wrong because distributions
etc generally compile I2C as a module and the commit broken that.
This patch is to rename I2C_ACPI to ACPI_I2C_OPREGION. New config
only controls ACPI I2C operation region code and depends on I2C=y.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: removed unrelated change for Kconfig]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull md bugfixes from Neil Brown:
 "Here are the bug-fixes I promised :-)

  Funny how you start looking for one and other start appearing.

   - raid6 data corruption during recovery
   - raid6 livelock
   - raid10 memory leaks"

* tag 'md/3.17-fixes' of git://neil.brown.name/md:
  md/raid10: always initialise ->state on newly allocated r10_bio
  md/raid10: avoid memory leak on error path during reshape.
  md/raid10: Fix memory leak when raid10 reshape completes.
  md/raid10: fix memory leak when reshaping a RAID10.
  md/raid6: avoid data corruption during recovery of double-degraded RAID6
  md/raid5: avoid livelock caused by non-aligned writes.

Pull PCI changes from Bjorn Helgaas:
 "Marvell MVEBU
    - Remove ARCH_KIRKWOOD dependency (Andrew Lunn)

  NVIDIA Tegra
    - Add debugfs support (Thierry Reding)

  Synopsys DesignWare
    - Look for configuration space in 'reg', not 'ranges' (Kishon Vijay Abraham I)
    - Program ATU with untranslated address (Kishon Vijay Abraham I)
    - Add config access-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
    - Add MSI-related pcie_host_ops for v3.65 hardware (Murali Karicheri)

  TI DRA7xx
    - Add TI DR7xx PCIe driver (Kishon Vijay Abraham I)"

* tag 'pci-v3.17-changes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: designware: Add MSI-related pcie_host_ops for v3.65 hardware
  PCI: designware: Add config access-related pcie_host_ops for v3.65 hardware
  PCI: dra7xx: Add TI DRA7xx PCIe driver
  PCI: designware: Program ATU with untranslated address
  PCI: designware: Look for configuration space in 'reg', not 'ranges'
  PCI: tegra: Add debugfs support
  PCI: mvebu: Remove ARCH_KIRKWOOD dependency

Pull devicetree fixes from Grant Likely:
 "Three more commits needed for v3.17: A bug fix for reserved regions
  based at address zero, a clarification on how to interpret existence
  of both interrupts and interrupts-extended properties, and a fix to
  allow device tree testcases to run on any platform"

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
  of/irq: Fix lookup to use 'interrupts-extended' property first
  Enabling OF selftest to run without machine's devicetree
  of: Allow mem_reserve of memory with a base address of zero

3a6bfbc9 "(arch,locking: Ciao arch_mutex_cpu_relax()") broke
building the frv arch.  Fixes errors such as:

  kernel/locking/mcs_spinlock.h:87:2: error: implicit declaration of function 'cpu_relax_lowlatency'
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As a generic function, deassign_guest_irq() assumes it can be called
even if assign_guest_irq() is not be called successfully (which can be
triggered by ioctl from user mode, indirectly).

So for assign_guest_irq() failure process, need set 'dev->irq_source_id'
to -1 after free 'dev->irq_source_id', or deassign_guest_irq() may free
it again.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

This reverts commit 682367c4,
which causes 32-bit SMP Windows 7 guests to panic.

SeaBIOS has a limit on the number of MTRRs that it can handle,
and this patch exceeded the limit.  Better revert it.
Thanks to Nadav Amit for debugging the cause.

Cc: stable@nongnu.org
Reported-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

This reverts the check added by commit 5045b468 (KVM: x86: check CS.DPL
against RPL during task switch, 2014-05-15).  Although the CS.DPL=CS.RPL
check is mentioned in table 7-1 of the SDM as causing a #TSS exception,
it is not mentioned in table 6-6 that lists "invalid TSS conditions"
which cause #TSS exceptions. In fact it causes some tests to fail, which
pass on bare-metal.

Keep the rest of the commit, since we will find new uses for it in 3.18.
Reported-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Commit d40a6898 mistakenly caused instructions which are not marked as
EmulateOnUD to be emulated upon #UD exception. The commit caused the check of
whether the instruction flags include EmulateOnUD to never be evaluated. As a
result instructions whose emulation is broken may be emulated.  This fix moves
the evaluation of EmulateOnUD so it would be evaluated.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Tweak operand order in &&, remove EmulateOnUD where it's now superfluous.
 - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

fc95ca72 claims that there is no
functional change but this is not true as it calls get_order() (which
takes bytes) where it should have called order_base_2() and the kernel
stops on VM_BUG_ON().

This replaces get_order() with order_base_2() (round-up version of ilog2).
Suggested-by: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The third parameter of kvm_iommu_put_pages is wrong,
It should be 'gfn - slot->base_gfn'.

By making gfn very large, malicious guest or userspace can cause kvm to
go to this error path, and subsequently to pass a huge value as size.
Alternatively if gfn is small, then pages would be pinned but never
unpinned, causing host memory leak and local DOS.

Passing a reasonable but large value could be the most dangerous case,
because it would unpin a page that should have stayed pinned, and thus
allow the device to DMA into arbitrary memory.  However, this cannot
happen because of the condition that can trigger the error:

- out of memory (where you can't allocate even a single page)
  should not be possible for the attacker to trigger

- when exceeding the iommu's address space, guest pages after gfn
  will also exceed the iommu's address space, and inside
  kvm_iommu_put_pages() the iommu_iova_to_phys() will fail.  The
  page thus would not be unpinned at all.
Reported-by: Jack Morgenstein <jackm@mellanox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Valleyview and Cherryview have the same behavior on display audio. So this patch
defines is_valleyview_plus() to include codecs for both Valleyview and its successor
Cherryview, and apply Valleyview fix-ups to Cherryview.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>