Rewrite i2c operations from i2c client read/write to regmap i2c. As
a result, most private functions now accept the private driver data
instead of an i2c client pointer.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Two actions were performed during remove - power supply dereg and
delayed work cleanup. Power supply dereg can be handled by using the
devm_ version of the registration function. Work cleanup can be added as
a devm_action.

If probe fails after psy registration it will now be cleaned up
properly.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Currently the sign for CURRENT_NOW and CURRENT_AVG is a bit
of a mess. There are basically 3 different ways battery fuel
gauges report the current:

1. uses negative values for discharging and positive values
   for charging
2. uses positive values for discharging and negative values
   for discharging (opposit of 1)
3. only uses positive values

As a result userspace currently cannot use the sign at all in
a generic way. Let's solve the issue by documenting a canonical
way for reporting the data and ensure new drivers follow this
way. Then existing drivers can be fixed on a case-by-case basis.

The 'negative value = battery discharging' has been choosen,
since there are only very few drivers doing it the other way
around.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add support for new device: the TI bq34z100-G1, a Wide Range Fuel Gauge
for Li-Ion, PbA, NiMH, and NiCd batteries.  The device shares a lot with
other models, although it has its own differences requiring new quirks.

This patch was tested on a system equipped with NiMH batteries.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

bq27000, bq27010 and upcoming bq34z100 have a Capacity Inaccurate flag.
However except this similarity, bq34z100 is quite different than
bq27000/bq27010, so flag BQ27XXX_O_ZERO cannot be reused here.  Add
a new bit flag describing this capability.

No functional change for bq27000 and bq27010.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

bq27000, bq27010 and upcoming bq34z100 have a single byte SoC
register.  However except this similarity, bq34z100 is quite different
than bq27000/bq27010, so flag BQ27XXX_O_ZERO cannot be reused here.  Add
a new bit flag describing that SoC is a single byte register.

No functional change for bq27000 and bq27010.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

BIT() is a preferred way to toggle bit-like flags: no problems with 32/64
bit systems, less chances for mistakes.  Remove also unneeded
whitespace.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Commit 6f24ff97 ("power: supply: bq27xxx_battery: Add the
BQ27Z561 Battery monitor") and commit d74534c2 ("power:
bq27xxx_battery: Add support for additional bq27xxx family devices")
added support for new device types by copying most of the code and
adding necessary quirks.

However they did not copy the code in bq27xxx_battery_status()
responsible for returning POWER_SUPPLY_STATUS_NOT_CHARGING.

Unify the bq27xxx_battery_status() so for all types when charger is
supplied, it will return "not charging" status.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add compatible for bq34z100 charger.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Some fault events like the over-current condition will get resolved
by the hardware, by e.g. disabling the port. As the status in the
interrupt status register is cleared on read when the fault is resolved,
the sysfs health property will only contain the correct health status
for the first time it is read after such an event, even if the actual
fault condition (like a VBUS short) still persists. To reflect this
properly in the property we cache the last health status and only update
the cache when a actual change happens, i.e. the ERR bit in the status
register flips, as this one properly reflects a continued fault condition.

The ALERT pin however, is not driven by the ERR status, but by the actual
fault status, so the pin will change back to it's default state when the
hardware has automatically resolved the fault by cutting the power. Thus
we never get an IRQ when the actual fault condition has been resolved and
the ERR status bit has been cleared in auto-recovery mode. To get this
information we need to poll the interrupt status register after some time
to see if the fault is gone and update our cache in that case.

To avoid any additional locking, we handle both paths (IRQ firing and
delayed polling) through the same single-threaded delayed work.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Andrews TI email is no longer valid and he indicated that it is
OK to remove him from the MAINTAINERS file for the DMA HEAPS FRAMEWORK.

For the BQ27xxx list I replaced Andrews email with mine.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Modify the comment typo: "compliment" -> "complement".
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Document new properties for IBAT compensation feature.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add configuration for compensation of IBAT measuring resistor in series
with the battery.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Modify the comment typo: "compliment" -> "complement".
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This binding can support Ingenic JZ4725B and JZ4770 SoCs, as they are
compatible with Ingenic JZ4740 battery.

Introduce the following compatible property combinations:
 compatible = "ingenic,jz4725b-battery", "ingenic,jz4740-battery",
 compatible = "ingenic,jz4770-battery", "ingenic,jz4740-battery"
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Convert the textual documentation of Device Tree bindings for the
Ingenic JZ47xx SoCs battery to YAML.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The bindings for charger-manager were very unclear and didn't
specify allowable values in many cases.  Clean these up to show
what each value does and make sure all properties are documented
here rather than using wildcards.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Rather than having a cm-chargers and a separate cm-num-chargers
property, simply count the entries in cm-chargers.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

In commit 830ae442 ("extcon: Remove the deprecated extcon functions")
the function extcon_register_interest became a no-op returning an error,
leading to non-functional behaviour in charger-manager.

Additionally, a translation table is needed between the text representation
of the extcon cable names and their IDs is needed.  In order to retain DT
compatibility, TA and CHARGE-DOWNSTREAM are added as they were present up
until commit 11eecf91 ("extcon: Modify the id and name of external
connector")
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Prevents direct charging control in cable notification and only set the
input current limit according to cable type.  Leave the enabling of
charing to cm_monitor() where charging management proceeds.  We may lose
a few ms to enable charging compared to before, but it's more important
that charging is enabled always in safe context.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

cm_monitor(), where charging management starts, checks various charging
condition sequentially to decide next charging operation. However, as it
follows sequential process, cascaded if statements, it does some
jobs which have already done in the previous stage. This results in a
delay in decision making. Moreover, starting point of charging is spread
all around which makes maintain code and debugging difficult.

Both of the problems mentioned above become clean if it manages battery
charging focusing on battery status not following sequential condition
checking.  Now, cm_monitor() moves battery state diagram and does the
optimal operation for current state. As a result, it reduces whole
monitoring time almost in half.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Current charger-manager calls power_supply_changed() whenever charging
status is changed. Remove the separated power_supply_changed() calls
and let it be called at end of try_charger_enable() function which
is called to set charging/discharging.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The POWER_SUPPLY_CHARGE_NOW/FULL property reflects battery's charges
in uAh unit, but charger-manager has been used it wrongly as a
status field.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

We were using POWER_SUPPLY_PROP_TEMP if the temperature was coming
via the fuel gauge and POWER_SUPPLY_PROP_TEMP_AMBIENT if it was
coming via the thermal framework.  Since they're mutually
exclusive in the driver and we don't know if the thermal framework
 is ambient or not, unify them both to use POWER_SUPPLY_PROP_TEMP.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

cm_notify_event() was introduced to get an event associated with the
battery status externally (ie in board files), but no one ever used it.
Moreover it makes charger manager driver more complicated. Drop the
function and all data related to it to simplify the driver.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Whenever the battery status is changed, charger manager triggers a uevent
through a private interface. Modify it to use power_supply_changed()
since it belongs to the power supply subsystem.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Both chips have charger and a fuel gauge.

This adds basic support for displaying the state of the battery and the
input power, settings are not modified. There are some defaults set via
OTP.

Charging also starts after plugging USB.

Known issues of the fuel gauge: There are drivers in the wild which disable
the fuel gauge at shutdown. If a kernel is booted without fuel gauge
support, after such a driver has been used, the fuel gauge will stay off
and decalibrate.
If this driver is used after that, it might display wrong values for charge
level.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Current sbs-battery considers all smbus errors as disconnection events
when battery-detect pin isn't supplied, and restored to present state back
when any successful transaction is made.

This can lead to unwanted state changes between present and !present
when there's one i2c error and other following commands were successful.

This patch provides a unified way of checking presence by calling
sbs_get_battery_presence_and_health() when detect pin is not used.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Simplify the driver and remove the DT specific code by
using the generic device property framework.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There are no platforms using the pdata support, so let's
drop it to simplify the driver.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Update the license to the SPDX licensing format.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This patch enables calling sbs_get_battery_presence_and_health()
without checking its chip type. No functional changes.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Remove unused enable_detection flag which is always true after
the device is proved.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add new charge-current-limit feature to gpio-charger.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Immutable branch between arm and power-supply for gpio-charger for 5.10

This immutable branch drops legacy gpio API from
gpio-charger and updates the remaining users to
the new gpiod API instead.
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This converts the GPIO charger to use exclusively GPIO
descriptors, moving the two remaining platforms passing
global GPIO numbers over to using a GPIO descriptor table.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>