It seems that there's a bug at au0828 hardware/firmware
related to alternate setting: when the device is already at
alt 5, a further call causes the URBs to receive -ESHUTDOWN.

I found two different encarnations of this issue:

1) at qv4l2, it fails the second time we try to open the
video screen;
2) at xawtv, when audio underrun occurs, with is very
frequent, at least on my test machine.

The fix is simple: just check if alt=5 before calling
set_usb_interface().

Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

There are several issues on the current code:
	1) msleep(1) is actually equivalent to msleep(10);
	2) au8522_video_set() will set reg 0xa4 to the
	   proper value for SIF, CVBS or S-Video. No need
	   to force it to CVBS;
	3) Let's not hardcode 0x9d for CBS on audio_set.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

setup_decoder_defaults() doesn't really care about the input
port. All it needs to know is if the input port is s-video or
not.

As the caller function already knows that, just pass a boolean
instead.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Let's set the the audio routing also at stream start. With this change,
we don't risk enabling the analog demux while not streaming, reducing
the risk of interfering with a DVB demux that might be happening.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The same demod is used on both analog and digital mode. We should
not let the commands for analog mode to happen while the device
is in digital mode. So, monitor it via streamon.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The input mode is used not only inside the setup_decoder_defaults()
but also at au8522_*_mode routines.

So, move it one level up. As an advantage, we can now group the
function that sets the input into just one.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The analog part of au0828 is missing the tuner Kconfig dependency.
That makes the device to not work while in analog mode.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add the basic GPLv2+ license notice to the copyright headers at the top
of all the source files in the img-ir driver.
Reported-by: David Härdeman <david@hardeman.nu>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The sh_mobile_ceu_camera and sh_mobile_csi2 drivers are only useful on
SuperH and shmobile unless build testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This patch change MACH_MX27 dependency to SOC_IMX27 for MX2 camera
driver, since MACH_MX27 symbol is scheduled for removal.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

That driver hasn't been really maintained for a long time. It doesn't
compile in any way, it includes non-existent headers, has no users,
and marked as "BROKEN" more than year. Due to these factors, mx1_camera
is now removed from the tree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The R-Car Video Input driver is only useful on shmobile unless build
testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The platform data is a single word, so simply copy
it into the device's private data structure than
keeping a copy of the pointer.

This will make changing to device-tree binding
easier as it is one allocation instead of two.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

devm_kzalloc() allocations are freed when the device is unbound. But if a
certain path fails and the allocated memory cannot be used anyway it is
better to free it explicitly immediately. This patch does exactly this if
asynchronous group probing in scan_async_group() fails after memory has
been allocated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Calibrate the signal strength to dB.

For this callibration, I used adapter 0 (antenna 1), connected
via a normal cable to a DTF-2111 generator.

The same cabling and RF generator connected to adapter 1
(antenna 2) has a difference of +3dBm (signal was stronger
there).

Yet, changing the RF for a difference of, let's say, 6dB
reflected on a 6dB difference at the measured signal, with
is good.

So, the signal strengh can indeed be used to measure the
antenna gain, if the antenna is repositioned. It is
not precise to measure the absolute dBm value, however.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Adds DVBv5 stats support. For now, just mimic whatever dib8000
does, as they're very similar, with regards to statistics.

However, dib7000p_get_time_us() likely require some
adjustments, as I didn't actually reviewed the formula
for it to work with DVB-T. Still, better than nothing,
as latter patches can improve it.

This patch also doesn't show the signal strength in dB
yet. The code is already there, but it requires to be
callibrated.

A latter patch will do the calibration.

It seems that this patch is also a bug fix: Before this
patch, the frontend were not tuning with some userspace
tools. I suspect that dib7000p firmware or hardware
internally expects that the statistics to be collected,
in order for it to work. With this patch, the DVB core
will always retrive statistics, even if userspace doesn't
request. So, it makes the device work on all tested apps.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.

The bug happens when:
        CONFIG_DVB_DIB8000=m
	CONFIG_DVB_USB_DIB0700=y

As a bonus, dib8000 won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.

Tested with both Pixelview PV-D231 and MyGica S870.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.

It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.

dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
  given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
  doesn't print who loaded the module);
- after loading the module, it runs the function associated
  with the dynamic symbol.

When compiled as builtin, it just calls the function given to it.

As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.

In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.

For almost all DVB frontends, there's just one function,
but, on dib8000, there are several exported symbols.

We need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.

So, let's rename this function, in order to prepare for
a next patch that will add a new attach() function that
will be the only one exported by this module.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.

This were reported several times, like:

   drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
   drivers/built-in.o: In function `dib7070_set_param_override':
   cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
   drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
   drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'

In this specific report:
	CONFIG_DVB_USB_CXUSB=y
	CONFIG_DVB_DIB7000P=m

But the same type of bug can happen if:
	CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).

As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.

Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.

It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.

dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
  given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
  doesn't print who loaded the module);
- after loading the module, it runs the function associated
  with the dynamic symbol.

When compiled as builtin, it just calls the function given to it.

As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.

In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.

For almost all DVB frontends, there's just one function.

However, the dib7000p initialization can require up to 3
functions to be called:
	- dib7000p_get_i2c_master;
	- dib7000p_i2c_enumeration;
	- dib7000p_init (before this patch dib7000_attach).

(plus a bunch of other functions that the bridge driver will
need to call).

As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.

So, let's rename the function that probes and init the hardware
to dib7000p_init.

A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The dvb_attach() was unbalanced, as there was no dvb_dettach. Ok,
on current cases, the dettach is done by dvbdev, but that are some
future corner cases where we may need to do this before registering
the frontend.

So, add a dvb_detach() and use it at dvb_frontend.c.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Change handling of signal_lock on rs2000. Use ibuf[2] to detect
lock as there is a longer wait for lock to appear in ibuf[6].

Remove last_key and key_timeout and use jiffies plus 60ms
to detect that streaming is still active.

If the current jiffies is time_after the interrupt urb overdue and
clear signal lock.

This results in far faster recovery of lock and streaming.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Replace resource handling in the driver with managed device resource.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Error handling code in usbtv_probe() misses usb_put_dev().

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The I2C address of the sensor device was in the middle of the sub-device
name and not in the end as it should have been. The smiapp sub-device names
will change from e.g. "vs6555 1-0010 pixel array" to "vs6555 pixel array
1-0010".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This patch does the following:

1: sets initial default format during probe.
2: removes spurious messages.
3: optimize vpif_s/try_fmt_vid_out code.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Remove bogus 'numbuffers' and 'bufsize' module options. The number of buffers and
buffer sizes are determined by VIDIOC_REQBUFS and VIDIOC_S_FMT and the amount of
available memory (in the case of the MMAP stream I/O mode) and not by module
options.

These module params are a left-over from the original montavista code that used
these parameters to pre-allocate the memory needed for the buffers. The code that
allocated those buffers was never upstreamed since by the time the drivers were
added to the kernel the TI cmem module could be used in combination with the
USERPTR mode to reserve and pass physically contiguous memory pointers around.

These days of course CMA is used instead of cmem.

This patch removes these module options altogether since they no longer do what
they originally were designed for. They should never have been part of the
upstreamed code in the first place, so they've been pointless ever since
2.6.32 when this driver first appeared in the mainline kernel.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

This symbol is not used externally. Get rid of it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The field is assigned but never read, remove it.

This fixes a bug caused by the struct vb2_buffer field not being be the
very first field of the vsp1_video_buffer buffer structure as required
by videobuf2.

Cc: stable@vger.kernel.org
Reported-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Linux 3.16-rc1

* tag 'v3.16-rc1': (11443 commits)
  Linux 3.16-rc1
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  fix __swap_writepage() compile failure on old gcc versions
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer
  x86/vdso: Fix vdso_install
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  btrfs: fix error handling in create_pending_snapshot
  btrfs: fix use of uninit "ret" in end_extent_writepage()
  btrfs: free ulist in qgroup_shared_accounting() error path
  Btrfs: fix qgroups sanity test crash or hang
  btrfs: prevent RCU warning when dereferencing radix tree slot
  Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
  btrfs: new ioctl TREE_SEARCH_V2
  ...

Pull networking fixes from David Miller:

 1) Fix checksumming regressions, from Tom Herbert.

 2) Undo unintentional permissions changes for SCTP rto_alpha and
    rto_beta sysfs knobs, from Denial Borkmann.

 3) VXLAN, like other IP tunnels, should advertize it's encapsulation
    size using dev->needed_headroom instead of dev->hard_header_len.
    From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer

Pull more clock framework updates from Mike Turquette:
 "This contains the second half the of the clk changes for 3.16.

  They are simply fixes and code refactoring for the OMAP clock drivers.
  The sunxi clock driver changes include splitting out the one
  mega-driver into several smaller pieces and adding support for the A31
  SoC clocks"

* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
  clk: sunxi: document PRCM clock compatible strings
  clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
  clk: sun6i: Protect SDRAM gating bit
  clk: sun6i: Protect CPU clock
  clk: sunxi: Rework clock protection code
  clk: sunxi: Move the GMAC clock to a file of its own
  clk: sunxi: Move the 24M oscillator to a file of its own
  clk: sunxi: Remove calls to clk_put
  clk: sunxi: document new A31 USB clock compatible
  clk: sunxi: Implement A31 USB clock
  ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
  CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
  ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
  CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
  CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
  dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
  ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
  CLK: TI: gate: add composite interface clock to OMAP2 only build
  ARM: OMAP2: clock: add DT boot support for cpufreq_ck
  CLK: TI: OMAP2: add clock init support
  ...

Pull NVMe update from Matthew Wilcox:
 "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
  exported tracepoint in the block layer; I believe Keith has cleared
  this with Jens.

  We've had a few reports from people who're really pounding on NVMe
  devices at scale, hence the timeout changes (and new module
  parameters), hotplug cpu deadlock, tracepoints, and minor performance
  tweaks"

[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
  end up going away when mq conversion happens ]

* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  NVMe: Use Log Page constants in SCSI emulation
  NVMe: Define Log Page constants
  NVMe: Fix hot cpu notification dead lock
  NVMe: Rename io_timeout to nvme_io_timeout
  NVMe: Use last bytes of f/w rev SCSI Inquiry
  NVMe: Adhere to request queue block accounting enable/disable
  NVMe: Fix nvme get/put queue semantics
  NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
  NVMe: Make admin timeout a module parameter
  NVMe: Make iod bio timeout a parameter
  NVMe: Prevent possible NULL pointer dereference
  NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
  NVMe: Update data structures for NVMe 1.2
  NVMe: Enable BUILD_BUG_ON checks
  NVMe: Update namespace and controller identify structures to the 1.1a spec
  NVMe: Flush with data support
  NVMe: Configure support for block flush
  NVMe: Add tracepoints
  NVMe: Protect against badly formatted CQEs
  ...

Commit 3fd091e7 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.

RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:

  [...]
  C3)  When a new RTT measurement R' is made, set

       RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|

       and

       SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'

       Note: The value of SRTT used in the update to RTTVAR
       is its value before updating SRTT itself using the
       second assignment. After the computation, update
       RTO <- SRTT + 4 * RTTVAR.

  C4)  When data is in flight and when allowed by rule C5
       below, a new RTT measurement MUST be made each round
       trip. Furthermore, new RTT measurements SHOULD be
       made no more than once per round trip for a given
       destination transport address. There are two reasons
       for this recommendation: First, it appears that
       measuring more frequently often does not in practice
       yield any significant benefit [ALLMAN99]; second,
       if measurements are made more often, then the values
       of RTO.Alpha and RTO.Beta in rule C3 above should be
       adjusted so that SRTT and RTTVAR still adjust to
       changes at roughly the same rate (in terms of how many
       round trips it takes them to reflect new values) as
       they would if making only one measurement per
       round-trip and using RTO.Alpha and RTO.Beta as given
       in rule C3. However, the exact nature of these
       adjustments remains a research issue.
  [...]

While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.

Fixes: 3fd091e7 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
Fixes related to some recent checksum modifications.

- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
  whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>