- 12 Aug, 2013 40 commits
-
-
Rafael J. Wysocki authored
commit 228b3023 upstream. Revert commit e11538d1 (cpuidle: Quickly notice prediction failure in general case), since it depends on commit 69a37bea (cpuidle: Quickly notice prediction failure for repeat mode) that has been identified as the source of a significant performance regression in v3.8 and later. Requested-by:
Jeremy Eder <jeder@redhat.com> Tested-by:
Len Brown <len.brown@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lan Tianyu authored
commit 016d5baa upstream. The _BIX method returns extended battery info as a package. According the ACPI spec (ACPI 5, Section 10.2.2.2), the first member of that package should be "Revision". However, the current ACPI battery driver treats the first member as "Power Unit" which should be the second member. This causes the result of _BIX return data parsing to be incorrect. Fix this by adding a new member called 'revision' to struct acpi_battery and adding the offsetof() information on it to extended_info_offsets[] as the first row. [rjw: Changelog] Reported-and-tested-by:
Jan Hoffmann <jan.christian.hoffmann@gmail.com> References: http://bugzilla.kernel.org/show_bug.cgi?id=60519Signed-off-by:
Lan Tianyu <tianyu.lan@intel.com> Signed-off-by:
-
Jiang Liu authored
commit 5863e10b upstream. Use zram->init_lock to protect access to zram->meta, otherwise it may cause invalid memory access if zram->meta has been freed by zram_reset_device(). This issue may be triggered by: Thread 1: while true; do cat mem_used_total; done Thread 2: while true; do echo 8M > disksize; echo 1 > reset; done Signed-off-by:
Jiang Liu <jiang.liu@huawei.com> Acked-by:
Minchan Kim <minchan@kernel.org> Signed-off-by:
-
Jiang Liu authored
commit 12a7ad3b upstream. Function valid_io_request() should verify the entire request are within the zram device address range. Otherwise it may cause invalid memory access when accessing/modifying zram->meta->table[index] because the 'index' is out of range. Then it may access non-exist memory, randomly modify memory belong to other subsystems, which is hard to track down. Signed-off-by:
-
Jiang Liu authored
commit 65c48460 upstream. When doing a patial write and the whole page is filled with zero, zram_bvec_write() will free uncmem twice. Signed-off-by:
-
Jiang Liu authored
commit 39a9b8ac upstream. On error recovery path of zram_init(), it leaks the zram device object causing the failure. So change create_device() to free allocated resources on error path. Signed-off-by:
Jerome Marchand <jmarchan@redhat.com> Signed-off-by:
-
Jiang Liu authored
commit 57ab0485 upstream. zram_slot_free_notify() is free-running without any protection from concurrent operations. So there are race conditions between zram_bvec_read()/zram_bvec_write() and zram_slot_free_notify(), and possible consequences include: 1) Trigger BUG_ON(!handle) on zram_bvec_write() side. 2) Access to freed pages on zram_bvec_read() side. 3) Break some fields (bad_compress, good_compress, pages_stored) in zram->stats if the swap layer makes concurrently call to zram_slot_free_notify(). So enhance zram_slot_free_notify() to acquire writer lock on zram->lock before calling zram_free_page(). Signed-off-by:
-
Jiang Liu authored
commit 6030ea9b upstream. Memory for zram->disk object may have already been freed after returning from destroy_device(zram), then it's unsafe for zram_reset_device(zram) to access zram->disk again. We can't solve this bug by flipping the order of destroy_device(zram) and zram_reset_device(zram), that will cause deadlock issues to the zram sysfs handler. So fix it by holding an extra reference to zram->disk before calling destroy_device(zram). Signed-off-by:
-
Avinash Patil authored
commit 237b2ac8 upstream. This patch fixes an issue wherein adhoc rates were being copied into association request from P2P client. Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
Stone Piao <piaoyun@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Avinash Patil authored
commit 953b3539 upstream. This patch fixes an issue wherein association would fail on P2P interfaces. This happened because we are checking priv->mode against NL80211_IFTYPE_STATION. While this check is correct for infrastructure stations, it would fail P2P clients for which mode is NL80211_IFTYPE_P2P_CLIENT. Better check would be bss_role which has only 2 values: STA/AP. Signed-off-by:
-
Tomasz Moń authored
commit 83e612f6 upstream. Both type and pkt_len variables are in host endian and these should be in Little Endian in the payload. Signed-off-by:
Tomasz Moń <desowin@gmail.com> Acked-by:
-
Stanislaw Gruszka authored
commit e2288b66 upstream. Since we clear QUEUE_STARTED in rt2x00queue_stop_queue(), following call to rt2x00queue_pause_queue() reduce to noop, i.e we do not stop queue in mac80211. To fix that introduce rt2x00queue_pause_queue_nocheck() function, which will stop queue in mac80211 directly. Note that rt2x00_start_queue() explicitly set QUEUE_PAUSED bit. Note also that reordering operations i.e. first call to rt2x00queue_pause_queue() and then clear QUEUE_STARTED bit, will race with rt2x00queue_unpause_queue(), so calling ieee80211_stop_queue() directly is the only available solution to fix the problem without major rework. Signed-off-by:
Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by:
-
J. Bruce Fields authored
commit 743e2171 upstream. mech_oid.data is an array, not kmalloc()'d memory. Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
J. Bruce Fields authored
commit 9f96392b upstream. Signed-off-by:
-
J. Bruce Fields authored
commit dc43376c upstream. Uninitialized stack data was being used as the destination for memcpy's. Longer term we'll just delete some of this code; all we're doing is skipping over xdr that we don't care about. Signed-off-by:
-
Adam Lee authored
commit d9c78e97 upstream. PTR_ERR() returns a signed long type value which is limited by IS_ERR(), it must be a negative number whose range is [-MAX_ERRNO, 0). The bug here returns negative numbers as error codes, then check it by "if (ret < 0)", but -PTR_ERR() is actually positive. The wrong use here leads to failure as below, even panic. [ 12.958920] Bluetooth: hci0 command 0xfc8e tx timeout [ 14.961765] Bluetooth: hci0 command 0xfc8e tx timeout [ 16.964688] Bluetooth: hci0 command 0xfc8e tx timeout [ 20.954501] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110) [ 22.957358] Bluetooth: hci0 command 0xfc8e tx timeout [ 30.948922] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110) [ 32.951780] Bluetooth: hci0 command 0xfc8e tx timeout [ 40.943359] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110) [ 42.946219] Bluetooth: hci0 command 0xfc8e tx timeout [ 50.937812] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110) [ 52.940670] Bluetooth: hci0 command 0xfc8e tx timeout [ 60.932236] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110) [ 62.935092] Bluetooth: hci0 command 0xfc8e tx timeout [ 70.926688] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110) [ 72.929545] Bluetooth: hci0 command 0xfc8e tx timeout [ 80.921111] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110) [ 82.923969] Bluetooth: hci0 command 0xfc2f tx timeout [ 90.915542] Bluetooth: hci0 sending Intel patch command (0xfc2f) failed (-110) [ 92.918406] Bluetooth: hci0 command 0xfc11 tx timeout [ 100.909955] Bluetooth: hci0 sending Intel patch command (0xfc11) failed (-110) [ 102.912858] Bluetooth: hci0 command 0xfc60 tx timeout [ 110.904394] Bluetooth: hci0 sending Intel patch command (0xfc60) failed (-110) [ 112.907293] Bluetooth: hci0 command 0xfc11 tx timeout [ 120.898831] Bluetooth: hci0 exiting Intel manufacturer mode failed (-110) [ 120.904757] bluetoothd[1030]: segfault at 4 ip 00007f8b2eb55236 sp 00007fff53ff6920 error 4 in bluetoothd[7f8b2eaff000+cb000] Signed-off-by:
Adam Lee <adam.lee@canonical.com> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
-
Cho, Yu-Chen authored
commit 178c059e upstream. This patch adds support for Mediatek Bluetooth device T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0e8d ProdID=763f Rev= 1.00 S: Manufacturer=MediaTek S: Product=BT S: SerialNumber=1.0 C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=450mA A: FirstIf#= 0 IfCount= 2 Cls=ff(vend.) Sub=ff Prot=ff I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by:
Cho, Yu-Chen <acho@suse.com> Signed-off-by:
-
AceLan Kao authored
commit 1d5b569e upstream. Add support for the AR9462 chip T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=e003 Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
AceLan Kao <acelan.kao@canonical.com> Signed-off-by:
-
AceLan Kao authored
commit 1ebd0b21 upstream. Add support for the AR3012 chip. T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=01 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=3121 Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
-
Sujith Manoharan authored
commit 5b77a1f3 upstream. T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3402 Rev= 0.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Bug: https://bugzilla.kernel.org/show_bug.cgi?id=59701Signed-off-by:
Sujith Manoharan <sujith@msujith.org> Signed-off-by:
-
Stanislaw Gruszka authored
commit 517828a8 upstream. Memory allocated by vmalloc (including stack) can not be used for DMA, i.e. data pointer on usb_control_msg() should not point to stack memory. Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=977558Reported-and-tested-by:
Andy Lawrence <dr.diesel@gmail.com> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Thomas Loo authored
commit 84eb2ae1 upstream. The Fujitsu Lifebook UH552/UH572 ships with a Qualcomm AR9462/AR3012 WLAN/BT-Combo card. Add device ID to the ath3k driver to enable the bluetooth side of things. Patch against v3.10. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04c5 ProdID=1330 Rev=00.02 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
Thomas Loo <tloo@saltstorm.net> Signed-off-by:
-
Larry Finger authored
commit 5d21608a upstream. Building driver wil6210 in 3.10 and 3.11 kernels yields the following errors: CC [M] drivers/net/wireless/ath/wil6210/debugfs.o drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_print_ring': drivers/net/wireless/ath/wil6210/debugfs.c:163:11: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign] false); ^ In file included from include/linux/kernel.h:13:0, from include/linux/cache.h:4, from include/linux/time.h:4, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/net/wireless/ath/wil6210/debugfs.c:17: include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *' extern void hex_dump_to_buffer(const void *buf, size_t len, ^ drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_txdesc_debugfs_show': drivers/net/wireless/ath/wil6210/debugfs.c:429:10: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign] sizeof(printbuf), false); ^ In file included from include/linux/kernel.h:13:0, from include/linux/cache.h:4, from include/linux/time.h:4, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/net/wireless/ath/wil6210/debugfs.c:17: include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *' extern void hex_dump_to_buffer(const void *buf, size_t len, ^ cc1: all warnings being treated as errors make[5]: *** [drivers/net/wireless/ath/wil6210/debugfs.o] Error 1 make[4]: *** [drivers/net/wireless/ath/wil6210] Error 2 make[3]: *** [drivers/net/wireless/ath] Error 2 make[2]: *** [drivers/net/wireless] Error 2 make[1]: *** [drivers/net] Error 2 make: *** [drivers] Error 2 These errors are fixed by changing the type of the buffer from "unsigned char *" to "char *". Reported-by:
Thomas Fjellstrom <thomas@fjellstrom.ca> Tested-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Thomas Fjellstrom <thomas@fjellstrom.ca> Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
-
Jacob Keller authored
commit 1eb9ac14 upstream. This patch fixes an issue with the 82598EB device, where lldpad is causing Tx Hangs on the card as soon as it attempts to configure DCB for the device. The adapter will continually Tx hang and reset in a loop. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by:
Jack Morgan <jack.morgan@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Stanislaw Gruszka authored
commit cd34f647 upstream. My commit: commit 12e7f517 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Thu Feb 28 10:55:26 2013 +0100 mac80211: cleanup generic suspend/resume procedures removed check for deleting MONITOR and AP_VLAN when suspend. That can cause a crash (i.e. in iwlagn_mac_remove_interface()) since we remove interface in the driver that we did not add before. Reference: http://marc.info/?l=linux-kernel&m=137391815113860&w=2Bisected-by:
Ortwin Glück <odi@odi.ch> Reported-and-tested-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
commit e13bae4f upstream. As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514, the station loop never initialises 'sinfo' and therefore adds up a stack values, leaking stack information (the number of times it adds values is easily obtained another way.) Fix this by initialising the sinfo for each station to add. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Johannes Berg authored
commit 6b0f3274 upstream. The duplicate retransmission detection code in mac80211 erroneously attempts to do the check for every frame, even frames that don't have a sequence control field or that don't use it (QoS-Null frames.) This is problematic because it causes the code to access data beyond the end of the SKB and depending on the data there will drop packets erroneously. Correct the code to not do duplicate detection for such frames. I found this error while testing AP powersave, it lead to retransmitted PS-Poll frames being dropped entirely as the data beyond the end of the SKB was always zero. Signed-off-by:
-
Felix Fietkau authored
commit 1cd15857 upstream. The CCK group needs special treatment to set the right flags and rate index. Add this missing check to prevent setting broken rates for tx packets. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
commit 5c9fc93b upstream. When priv_sta == NULL, mi->prev_sample is dereferenced too early. Move the assignment further down, after the rate_control_send_low call. Reported-by:
Krzysztof Mazur <krzysiek@podlesie.net> Signed-off-by:
-
Michal Kazior authored
commit a0ec570f upstream. These two events were sent to the default network namespace. This caused AP mode in a non-default netns to not work correctly. Mgmt tx status was multicasted to a different (default) netns instead of the one the AP was in. Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
-
Oleksij Rempel authored
commit 4928bd2e upstream. Currently ath9k_htc will reboot firmware only if interface was ever started. Which lead to the problem in case where interface was never started but module need to be reloaded. This patch will partially fix bug "ath9k_htc: Target is unresponsive" https://github.com/qca/open-ath9k-htc-firmware/issues/1 Reproduction case: - plug adapter - make sure nothing will touch it. Stop Networkmanager or blacklist mac address of this adapter. - rmmod ath9k_htc; sleep 1; modprobe ath9k_htc Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
-
Oleksij Rempel authored
commit dc2a87f5 upstream. Currently we configure harwdare and clock, only after interface start. In this case, if we reload module or reboot PC without configuring adapter, firmware will freeze. There is no software way to reset adpter. This patch add initial configuration and set it in disabled state, to avoid this freeze. Behaviour of this patch should be similar to: ifconfig wlan0 up; ifconfig wlan0 down. Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1Tested-by:
Bo Shi <cnshibo@gmail.com> Signed-off-by:
-
Johannes Berg authored
commit b6658ff8 upstream. When a not fully started aggregation session is destroyed and flushed, we get a warning, e.g. WARNING: at drivers/net/wireless/iwlwifi/pcie/tx.c:1142 iwl_trans_pcie_txq_disable+0x11c/0x160 queue 16 not used Modules linked in: [...] Pid: 5135, comm: hostapd Tainted: G W O 3.5.0 #10 Call Trace: wlan0: driver sets block=0 for sta 00:03:7f:10:44:d3 [<ffffffff81036492>] warn_slowpath_common+0x72/0xa0 [<ffffffff81036577>] warn_slowpath_fmt+0x47/0x50 [<ffffffffa0368d6c>] iwl_trans_pcie_txq_disable+0x11c/0x160 [iwlwifi] [<ffffffffa03a2099>] iwl_mvm_sta_tx_agg_flush+0xe9/0x150 [iwlmvm] [<ffffffffa0396c43>] iwl_mvm_mac_ampdu_action+0xf3/0x1e0 [iwlmvm] [<ffffffffa0293ad3>] ___ieee80211_stop_tx_ba_session+0x193/0x920 [mac80211] [<ffffffffa0294ed8>] __ieee80211_stop_tx_ba_session+0x48/0x70 [mac80211] [<ffffffffa029159f>] ieee80211_sta_tear_down_BA_sessions+0x4f/0x80 [mac80211] [<ffffffffa028a686>] __sta_info_destroy+0x66/0x370 [mac80211] [<ffffffffa028abb4>] sta_info_destroy_addr_bss+0x44/0x70 [mac80211] [<ffffffffa02a3e26>] ieee80211_del_station+0x26/0x50 [mac80211] [<ffffffffa01e6395>] nl80211_del_station+0x85/0x200 [cfg80211] when a station deauthenticated from us without fully setting up the aggregation session. Fix this by checking the aggregation state before removing the hardware queue. Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit a1923f1d upstream. This SKU was missing in the list of supported devices https://bugzilla.kernel.org/show_bug.cgi?id=60577Signed-off-by:
-
Johannes Berg authored
commit 48bc1307 upstream. Due to a firmware bug, it crashes when the beacon interval is smaller than 16. Avoid this by refusing the station state change creating the AP station, causing mac80211 to abandon the attempt to connect to the AP, and eventually wpa_s to blacklist it. Reviewed-by:
-
David Spinadel authored
commit fe04e837 upstream. Increment index in each iteration. Without this increment we are overriding the added SSIDs and we will send only the last SSId and (n_ssids - 1) broadcast probes. Signed-off-by:
David Spinadel <david.spinadel@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 93a42667 upstream. We didn't release the Rx AMPDU ressources properly. This bug led to firmware assert after 16 BA sessions. Signed-off-by:
-
Johan Hovold authored
commit 683a0e4d upstream. Silence compiler warnings on 64-bit systems introduced by commit 05cf0dec ("USB: mos7840: fix race in led handling") which uses the usb-serial data pointer to temporarily store the device type during probe but failed to add the required casts. [gregkh - change uintptr_t to unsigned long] Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 05cf0dec upstream. Fix race in LED handling introduced by commit 0eafe4de ("USB: serial: mos7840: add support for MCS7810 devices") which reused the port control urb for manipulating the LED without making sure that the urb is not already in use. This could lead to the control urb being manipulated while in flight. Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy flag to handle concurrency. Signed-off-by:
-
Johan Hovold authored
commit 40c24f28 upstream. Fix race in device-type detection introduced by commit 0eafe4de ("USB: serial: mos7840: add support for MCS7810 devices") which used a static variable to hold the device type. Move type detection to probe and use serial data to store the device type. Signed-off-by:
-
