All devices are capable of using regular DSA tags. Support for
Ethertyped DSA tags sort into three categories:

1. No support. Older chips fall into this category.

2. Full support. Datasheet explicitly supports configuring the CPU
   port to receive FORWARDs with a DSA tag.

3. Undocumented support. Datasheet lists the configuration from
   category 2 as "reserved for future use", but does empirically
   behave like a category 2 device.

So, instead of listing the one true protocol that should be used by a
particular chip, specify the level of support for EDSA (support for
regular DSA is implicit on all chips). As before, we use EDSA for all
chips that fully supports it.

In upcoming changes, we will use this information to support
dynamically changing the tag protocol.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-net-next-2021-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
Another set of updates, all over the map:
 * set sk_pacing_shift for 802.3->802.11 encap offload
 * some monitor support for 802.11->802.3 decap offload
 * HE (802.11ax) spec updates
 * userspace API for TDLS HE support
 * along with various other small features, cleanups and
   fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Machata says:

====================
mlxsw: Refactor qdisc offload

Currently, mlxsw admits for offload a suitable root qdisc, and its
children. Thus up to two levels of hierarchy are offloaded. Often, this is
enough: one can configure TCs with RED and TCs with a shaper, and can even
see counters for each TC by looking at a qdisc at a sufficiently shallow
position.

While simple, the system has obvious shortcomings. It is not possible to
configure both RED and shaping on one TC. It is not possible to place a
PRIO below root TBF, which would then be offloaded as port shaper. FIFOs
are only offloaded at root or directly below, which is confusing to users,
because RED and TBF of course have their own FIFO.

This patchset is a step towards the end goal of allowing more comprehensive
qdisc tree offload and cleans up the qdisc offload code.

- Patches #1-#4 contain small cleanups.

- Up until now, since mlxsw offloaded only a very simple qdisc
  configurations, basically all bookkeeping was done using one container
  for the root qdisc, and 8 containers for its children. Patches #5, #6, #8
  and #9 gradually introduce a more dynamic structure, where parent-child
  relationships are tracked directly at qdiscs, instead of being implicit.

- This tree management assumes only one qdisc is created at a time. In FIFO
  handlers, this condition was enforced simply by asserting RTNL lock. But
  instead of furthering this RTNL dependence, patch #7 converts the whole
  qdisc offload logic to a per-port mutex.

- Patch #10 adds a selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There was a bug introduced during the rework which cause non-zero backlog
being stuck at ETS. Introduce a selftest that would have caught the issue
earlier.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw used to hold an array of qdiscs indexed by the TC number. In the
previous patch, it was changed to allocate child qdiscs dynamically, and
they are now indexed by band number. Follow suit with the array of future
FIFOs.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of keeping qdiscs in globally-preallocated arrays, introduce a
per-qdisc-kind value num_classes, and then allocate the necessary child
qdiscs (if any) based on that value. Since now dynamic allocation is
involved, mlxsw_sp_qdisc_replace() gets messy enough that it is worth it to
split it to two cases: a new qdisc allocation and a change of existing
qdisc. (Note that the change also includes what TC formally calls replace,
if the qdisc kind is the same.)
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The FIFO handler currently guards accesses to the future FIFO tracking by
asserting RTNL. In the future, the changes to the qdisc state will be more
thorough, so other qdiscs will need this guarding is as well. In order
to not further the RTNL infestation, instead convert to a custom lock that
will guard accesses to the qdisc state.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw currently allows a two-level structure of qdiscs: the root and
possibly a number of children. In order to support offloading more general
qdisc trees, introduce to struct mlxsw_sp_qdisc a pointer to child qdiscs.
Refer to the child qdiscs through this pointer, instead of going through
the tclass_qdiscs in qdisc_state. Additionally introduce a field
num_classes, which holds number of given qdisc's children.

Also introduce a generic function for walking qdisc trees. Rewrite
mlxsw_sp_qdisc_find() and _find_by_handle() to use the generic walker.

For now, keep the qdisc_state.tclass_qdisc, and just point root_qdiscs's
children to this array. Following patches will make the allocation dynamic.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a qdisc is removed, it is necessary to update the backlog value at its
parent--unless the qdisc is at root position. RED, TBF and FIFO all do
that, each separately. Since all of them need to do this, just promote the
operation directly to mlxsw_sp_qdisc_destroy(), instead of deferring it to
individual destructors. Since FIFO dtor thus becomes trivial, remove it.

Add struct mlxsw_sp_qdisc.parent to point at the parent qdisc. This will be
handy later as deeper structures are offloaded. Use the parent qdisc to
find the chain of parents whose backlog value needs to be updated.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tclass_num is just a number, a value that would be ordinarily passed around
as an int. (Which is unlike a u8 prio_bitmap.) In several places,
tclass_num already is an int. Convert the remaining instances.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function mlxsw_sp_qdisc_compare() is invoked a couple lines above this
check, which will bounce any requests where this condition does not hold.
Therefore drop it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The purpose of this function is to filter out events that are related to
qdiscs that are not offloaded, or are not offloaded anymore. But the
function is unnecessarily thorough:

- mlxsw_sp_qdisc pointer is never NULL in the context where it is called
- Two qdiscs with the same handle will never have different types. Even
  when replacing one qdisc with another in the same class, Linux will not
  permit handle reuse unless the qdisc type also matches.

Simplify the function by omitting these two unnecessary conditions.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mlxsw_sp_qdisc argument is not used in any of the actual callbacks.
Drop it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Marek Behún says:

====================
net: phy: marvell: some HWMON updates

Here are some updates for Marvell PHY HWMON, mainly
- refactoring for code deduplication
- Amethyst PHY support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for Amethyst internal PHY.

The only difference from Peridot is HWMON.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Amethyst internal PHYs also report empty model number in MII_PHYSID2.

Fill in switch product number, as is done for Topaz and Peridot.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the &= operator instead of
  ret = ret & ...
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register 27_6.15:14 has the following description in 88E6393X
documentation:
  Temperature Sensor Enable
    0x0 - Sample every 1s
    0x1 - Sense rate decided by bits 10:8 of this register
    0x2 - Use 26_6.5 (One shot Temperature Sample) to enable
    0x3 - Disable

This is compatible with how the 6390 code uses this register currently,
but the 6390 code handles it as two 1-bit registers (somewhat), instead
of one register with 4 possible values.

(A newer version of the 6390 documentation removed temperature sensor
 section completely. In an older version, the above mentioned register
 is reserved, although it is R/W. Since the code works, I think we can
 assume that it is correct.)

Rename this register and define all 4 values according to 6393X
documentation.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a structure of Marvell PHY specific HWMON methods to reduce code
duplication. Store a pointer to this structure into the PHY driver's
driver_data member.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2021-04-19

This patchset provides some updates to mlx5e and mlx5 SW steering drivers:

1) Tariq and Vladyslav they both provide some trivial update to mlx5e netdev.

The next 12 patches in the patchset are focused toward mlx5 SW steering:
2) 3 trivial cleanup patches

3) Dynamic Flex parser support:
   Flex parser is a HW parser that can support protocols that are not
    natively supported by the HCA, such as Geneve (TLV options) and GTP-U.
    There are 8 such parsers, and each of them can be assigned to parse a
    specific set of protocols.

4) Enable matching on Geneve TLV options

5) Use Flex parser for MPLS over UDP/GRE

6) Enable matching on tunnel GTP-U and GTP-U first extension
   header using

7) Improved QoS for SW steering internal QPair for a better insertion rate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ALWAYS_GUARD_BAND_SCH_Q bit in TAS config register is descripted as
this:
	0: Guard band is implemented for nonschedule queues to schedule
	   queues transition.
	1: Guard band is implemented for any queue to schedule queue
	   transition.

The driver set guard band be implemented for any queue to schedule queue
transition before, which will make each GCL time slot reserve a guard
band time that can pass the max SDU frame. Because guard band time could
not be set in tc-taprio now, it will use about 12000ns to pass 1500B max
SDU. This limits each GCL time interval to be more than 12000ns.

This patch change the guard band to be only implemented for nonschedule
queues to schedule queues transition, so that there is no need to reserve
guard band on each GCL. Users can manually add guard band time for each
schedule queues in their configuration if they want.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Oleksij Rempel says:

====================
provide generic net selftest support

changes v3:
- make more granular tests
- enable loopback for all PHYs by default
- fix allmodconfig build errors
- poll for link status update after switching to the loopback mode

changes v2:
- make generic selftests available for all networking devices.
- make use of net_selftest* on FEC, ag71xx and all DSA switches.
- add loopback support on more PHYs.

This patch set provides diagnostic capabilities for some iMX, ag71xx or
any DSA based devices. For proper functionality, PHY loopback support is
needed.
So far there is only initial infrastructure with basic tests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Most of generic selftest should be able to work with probably all ethernet
controllers. The DSA switches are not exception, so enable it by default at
least for DSA.

This patch was tested with SJA1105 and AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

With this patch the ag71xx on Atheros AR9331 will able to run generic net
selftests.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

With this patch FEC on iMX will able to run generic net selftests
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Port some parts of the stmmac selftest and reuse it as basic generic selftest
library. This patch was tested with following combinations:
- iMX6DL FEC -> AT8035
- iMX6DL FEC -> SJA1105Q switch -> KSZ8081
- iMX6DL FEC -> SJA1105Q switch -> KSZ9031
- AR9331 ag71xx -> AR9331 PHY
- AR9331 ag71xx -> AR9331 switch -> AR9331 PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of loopback, in most cases we need to disable autoneg support
and force some speed configuration. Otherwise, depending on currently
active auto negotiated link speed, the loopback may or may not work.

This patch was tested with following PHYs: TJA1102, KSZ8081, KSZ9031,
AT8035, AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic loopback is really generic and is defined by the 802.3
standard, we should just mandate that drivers implement a custom
loopback if the generic one cannot work.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using SW steering, rule insertion rate depends on the RDMA RC QP
performance used for writing to the ICM. During stress this QP is competing
on the HW resources with all the other QPs that are used to send data.
To protect SW steering QP's performance in such cases, we set this QP to
use isolated VL. The VL number is reserved by FW and is not exposed to the
driver.
Support for this QP on isolated VL exists only when both force-loopback and
isolate_vl_tc capabilities are set.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When supported by the device, SW steering RoCE RC QP that is used to
write/read to/from ICM will be created with force-loopback attribute.
Such QP doesn't require GID index upon creation.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Enable matching on tunnel GTP-U and GTP-U first extension
header using dynamic flex parser.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Query the flex_parser id that's intended for TNL_MPLS
and use an appropriate flex parser for MPLS over UDP/GRE.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Enable matching on tunnel geneve TLV option using the flex parser.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Set the flex parser ID dynamicly for ICMP instead of relying
on hardcoded values.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Flex parser is a HW parser that can support protocols that are not
natively supported by the HCA, such as Geneve (TLV options) and GTP-U.
There are 8 such parsers, and each of them can be assigned to parse a
specific set of protocols.
This patch adds misc4 match params which allows using a correct flex parser
that was programmed to the required protocol.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Remove MPLS specific fields from flex parser 3 layout.
Flex parser can be used for multiple protocols and should
not be hardcoded to a specific type.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Added the required definitions for supporting more protocols by flex parsers
(GTP-U, Geneve TLV options), and for using the right flex parser that was
configured for this protocol.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add error code to the error messages and removed duplicated message:
if termination table creation failed, we already get an error message
in mlx5_eswitch_termtbl_create, so no need for the additional error print
in the calling function.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>