On certain platforms BE3 chips may indicate spurious UEs (unrecoverable
error). Because of the UE detection logic was disabled in the driver
for BE3 chips. Because of this, even in cases of a real UE,
a failover will not occur. This patch re-enables UE detection on BE3
and if a UE is detected, reads the POST register. If the POST register,
reports either a FAT_LOG_STATE or a ARMFW_UE, then it means that a valid
UE occurred in the chip.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support network namespacing in AF_RXRPC with the following changes:

 (1) All the local endpoint, peer and call lists, locks, counters, etc. are
     moved into the per-namespace record.

 (2) All the connection tracking is moved into the per-namespace record
     with the exception of the client connection ID tree, which is kept
     global so that connection IDs are kept unique per-machine.

 (3) Each namespace gets its own epoch.  This allows each network namespace
     to pretend to be a separate client machine.

 (4) The /proc/net/rxrpc_xxx files are now called /proc/net/rxrpc/xxx and
     the contents reflect the namespace.

fs/afs/ should be okay with this patch as it explicitly requires the current
net namespace to be init_net to permit a mount to proceed at the moment.  It
will, however, need updating so that cells, IP addresses and DNS records are
per-namespace also.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes unused parameter from prb_curr_blk_in_use() method
in net/packet/af_packet.c.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Corentin Labbe says:

====================
net-next: stmmac: rework the speed selection

The current stmmac_adjust_link() part which handle speed have
some if (has_platform) code and my dwmac-sun8i will add more of them.

So we need to handle better speed selection.
Moreover the struct link member speed and port are hard to guess their
purpose. And their unique usage are to be combined for writing speed.

My first try was to create an adjust_link() in stmmac_ops but it duplicate some code

The current solution is to have direct value for 10/100/1000 and a mask for them.

The first 4 patchs fix some minor problem found in stmmac_adjust_link() and reported by Florian Fainelli in my previous serie.
The last patch is the real work.

This series is tested on cubieboard2 (dwmac1000) and opipc (dwmac-sun8i).

Changes since v3:
- Added the patch #4 "Convert old_link to bool" as suggested by Joe Perches
- Changed the speedmask

Changes since v2:
- Use true/false for new_state in patch #1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current stmmac_adjust_link() part which handle speed have
some if (has_platform) code and my dwmac-sun8i will add more of them.

So we need to handle better speed selection.
Moreover the struct link member speed and port are hard to guess their
purpose. And their unique usage are to be combined for writing speed.

So this patch replace speed/port by simpler
speed10/speed100/speed1000/speed_mask variables.

In dwmac4_core_init and dwmac1000_core_init, port/speed value was used
directly without using the struct link. This patch convert also their
usage to speedxxx.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch convert old_link from int to bool since it store only 1 or 0
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch convert new_state from int to bool since it store only 1 or 0
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functions jme_restart_tx_engine(), jme_pause_rx() and
jme_resume_rx() are not used. Removing them fixes the following warnings
when building with clang:

drivers/net/ethernet/jme.c:694:1: error: unused function
    'jme_restart_tx_engine' [-Werror,-Wunused-function]

drivers/net/ethernet/jme.c:2393:20: error: unused function
    'jme_pause_rx' [-Werror,-Wunused-function]

drivers/net/ethernet/jme.c:2406:20: error: unused function
    'jme_resume_rx' [-Werror,-Wunused-function]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2017-05-23

Here's the first Bluetooth & 802.15.4 pull request targeting the 4.13
kernel release.

 - Bluetooth 5.0 improvements (Data Length Extensions and alternate PHY)
 - Support for new Intel Bluetooth adapter [[8087:0aaa]
 - Various fixes to ieee802154 code
 - Various fixes to HCI UART code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit af6b6967 ("net: phy: export genphy_config_init()") introduced
this EXPORT_SYMBOL and put it after gen10g_soft_reset() instead of
directly after genphy_config_init. Probably this happend when the patch
was applied because http://patchwork.ozlabs.org/patch/339622/ looks ok.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paul Fiterau Brostean reported :

<quote>
Linux TCP stack we analyze exhibits behavior that seems odd to me.
The scenario is as follows (all packets have empty payloads, no window
scaling, rcv/snd window size should not be a factor):

       TEST HARNESS (CLIENT)                        LINUX SERVER

   1.  -                                          LISTEN (server listen,
then accepts)

   2.  - --> <SEQ=100><CTL=SYN>               --> SYN-RECEIVED

   3.  - <-- <SEQ=300><ACK=101><CTL=SYN,ACK>  <-- SYN-RECEIVED

   4.  - --> <SEQ=101><ACK=301><CTL=ACK>      --> ESTABLISHED

   5.  - <-- <SEQ=301><ACK=101><CTL=FIN,ACK>  <-- FIN WAIT-1 (server
opts to close the data connection calling "close" on the connection
socket)

   6.  - --> <SEQ=101><ACK=99999><CTL=FIN,ACK> --> CLOSING (client sends
FIN,ACK with not yet sent acknowledgement number)

   7.  - <-- <SEQ=302><ACK=102><CTL=ACK>      <-- CLOSING (ACK is 102
instead of 101, why?)

... (silence from CLIENT)

   8.  - <-- <SEQ=301><ACK=102><CTL=FIN,ACK>  <-- CLOSING
(retransmission, again ACK is 102)

Now, note that packet 6 while having the expected sequence number,
acknowledges something that wasn't sent by the server. So I would
expect
the packet to maybe prompt an ACK response from the server, and then be
ignored. Yet it is not ignored and actually leads to an increase of the
acknowledgement number in the server's retransmission of the FIN,ACK
packet. The explanation I found is that the FIN  in packet 6 was
processed, despite the acknowledgement number being unacceptable.
Further experiments indeed show that the server processes this FIN,
transitioning to CLOSING, then on receiving an ACK for the FIN it had
send in packet 5, the server (or better said connection) transitions
from CLOSING to TIME_WAIT (as signaled by netstat).

</quote>

Indeed, tcp_rcv_state_process() calls tcp_ack() but
does not exploit the @acceptable status but for TCP_SYN_RECV
state.

What we want here is to send a challenge ACK, if not in TCP_SYN_RECV
state. TCP_FIN_WAIT1 state is not the only state we should fix.

Add a FLAG_NO_CHALLENGE_ACK so that tcp_rcv_state_process()
can choose to send a challenge ACK and discard the packet instead
of wrongly change socket state.

With help from Neal Cardwell.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Fiterau Brostean <p.fiterau-brostean@science.ru.nl>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcf_chain_get() always creates a new filter chain if not found
in existing ones. This is totally unnecessary when we get or
delete filters, new chain should be only created for new filters
(or new actions).

Fixes: 5bc17018 ("net: sched: introduce multichain support for filters")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the introduction of chain goto action, the reclassification would
cause the re-iteration of the actual chain. It makes more sense to restart
the whole thing and re-iterate starting from the original tp - start
of chain 0.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-update-2017-05-23

First patch from Leon, came to remove the redundant usage of mlx5_vzalloc,
and directly use kvzalloc across all mlx5 drivers.

2nd patch from Noa, adds new device IDs into the supported devices list.

3rd and 4th patches from Ilan are adding the basic infrastructure and
support for Mellanox's mlx5 FPGA.

Last two patches from Tariq came to modify the outdated driver version
reported in ethtool and in mlx5_ib to more reflect the current driver state
and remove the redundant date string reported in the version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After the mentioned commit, some of our packetdrill tests became flaky.

TCP_SYNCNT socket option can limit the number of SYN retransmits.

retransmits_timed_out() has to compare times computations based on
local_clock() while timers are based on jiffies. With NTP adjustments
and roundings we can observe 999 ms delay for 1000 ms timers.
We end up sending one extra SYN packet.

Gimmick added in commit 6fa12c85 ("Revert Backoff [v3]: Calculate
TCP's connection close threshold as a time value") makes no
real sense for TCP_SYN_SENT sockets where no RTO backoff can happen at
all.

Lets use a simpler logic for TCP_SYN_SENT sockets and remove @syn_set
parameter from retransmits_timed_out()

Fixes: 9a568de4 ("tcp: switch TCP TS option (RFC 7323) to 1ms clock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the switchdev bridge ageing time attribute is propagated to all
switch chips of the fabric, each switch can check if the requested value
is valid and program itself, so that the whole fabric shares a common
ageing time setting.

This is especially needed for switch chips in between others, containing
no bridge port members but evidently used in the data path.

To achieve that, remove the condition which skips the other switches. We
also don't need to identify the target switch anymore, thus remove the
sw_index member of the dsa_notifier_ageing_time_info notifier structure.

On ZII Dev Rev B (with two 88E6352 and one 88E6185) and ZII Dev Rev C
(with two 88E6390X), we have the following hardware configuration:

    # ip link add name br0 type bridge
    # ip link set master br0 dev lan6
    br0: port 1(lan6) entered blocking state
    br0: port 1(lan6) entered disabled state
    # echo 2000 > /sys/class/net/br0/bridge/ageing_time

Before this patch:

    zii-rev-b# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
    300000
    300000
    15000

    zii-rev-c# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
    300000
    18750

After this patch:

    zii-rev-b# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
    15000
    15000
    15000

    zii-rev-c# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
    18750
    18750
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
net: add tcp flags match support to flower and offload it

This patch adds support to dissect tcp flags, match on them using
flower classifier and offload such rules to mlxsw Spectrum devices.

v1->v2:
- removed no longer relevant comment from patch 1 as suggested by Or
- sent correct patches this time
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow to offload rules that contain tcp flags within the mask.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add acl block called "ipv4" which contains tcp flags.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define new element for tcp flags and place it into scratch area.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Benefit from the support of tcp flags dissection and allow user to
insert rules matching on tcp flags.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for dissection of tcp flags. Uses similar function call to
tcp dissection function as arp, mpls and others.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed/qede: Mostly-cleanup series

This series contains some cleanup of the qed and qede code:
 - #1 contains mostly static/endian changes in order to allow qede to
   pass sparse compilation cleanly.
 - #2, #5 and #6 are either semantic or remove dead-code from driver.
 - #9, #10 and #11 relate to printing and slightly change some APIs
   between qed and the protocol drivers for that end [sharing the
   interface names and information regarding device].

The rest of the patches are minor changes/fixes to various flows
in qed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Current API between qed and protocol modules allows passing an
additional private string - but it doesn't get utilized by qed
anywhere.

Clarify the API by removing it and renaming it 'set_name'.

CC: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace meaningless logged print ('Ending successfully qede probe')
with a single-liner containing interesting information about probed
device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass additional information about package installed on persistent memory
so that protocol drivers would be able to log it.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we're closing the parser searching for RDMA when stoping the
fastpath, we need to re-enable it when starting the fastpath once again.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Today, driver has a synchronization point while closing
the device which synchronizes its slowpath interrupt line.
However, that's insufficient as that ISR would schedule the
slowpath-tasklet - so even after ISR is over it's possible the
handling of the interrupt has not completed.

By doing a disable/enable on the taskelt we guarantee that all
HW events that should no longer be genereated from that point
onward in the flow are truly behind us.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A0 never went public, so no need to protect against it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The parameter reflects the number of physical ports connected to a single
engine, not all.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case nvram layout of board is incorrect, board may exhibit peculiar
oddities. Log such a rare event.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flows configuring tunnel ports in HW use the main_ptt which should
be reserved for core-functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Solves the following warning in qede -
 - Several cases of missing cpu_to_le16() conversions
 - Adds 'static' to one function declaration
 - Removes dcbnl operation that's currently getting populated twice
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Null check at line 918: if (!spi) {, implies spi might be NULL.
Function spi_get_drvdata() dereference pointer spi.
Move pointer priv assignment after the null check.

Addresses-Coverity-ID: 1408888
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch fixes the kernel oops when release net_device reference in
advance. In function raw_sendmsg(i think the dgram_sendmsg has the same
problem), there is a race condition between dev_put and dev_queue_xmit
when the device is gong that maybe lead to dev_queue_ximt to see
an illegal net_device pointer.

My test kernel is 3.13.0-32 and because i am not have a real 802154
device, so i change lowpan_newlink function to this:

        /* find and hold real wpan device */
        real_dev = dev_get_by_index(src_net, nla_get_u32(tb[IFLA_LINK]));
        if (!real_dev)
                return -ENODEV;
//      if (real_dev->type != ARPHRD_IEEE802154) {
//              dev_put(real_dev);
//              return -EINVAL;
//      }
        lowpan_dev_info(dev)->real_dev = real_dev;
        lowpan_dev_info(dev)->fragment_tag = 0;
        mutex_init(&lowpan_dev_info(dev)->dev_list_mtx);

Also, in order to simulate preempt, i change the raw_sendmsg function
to this:

        skb->dev = dev;
        skb->sk  = sk;
        skb->protocol = htons(ETH_P_IEEE802154);
        dev_put(dev);
        //simulate preempt
        schedule_timeout_uninterruptible(30 * HZ);
        err = dev_queue_xmit(skb);
        if (err > 0)
                err = net_xmit_errno(err);

and this is my userspace test code named test_send_data:

int main(int argc, char **argv)
{
        char buf[127];
        int sockfd;
        sockfd = socket(AF_IEEE802154, SOCK_RAW, 0);
        if (sockfd < 0) {
                printf("create sockfd error: %s\n", strerror(errno));
                return -1;
        }
        send(sockfd, buf, sizeof(buf), 0);
        return 0;
}

This is my test case:

root@zhanglin-x-computer:~/develop/802154# uname -a
Linux zhanglin-x-computer 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15
03:51:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux
root@zhanglin-x-computer:~/develop/802154# ip link add link eth0 name
lowpan0 type lowpan
root@zhanglin-x-computer:~/develop/802154#
//keep the lowpan0 device down
root@zhanglin-x-computer:~/develop/802154# ./test_send_data &
//wait a while
root@zhanglin-x-computer:~/develop/802154# ip link del link dev lowpan0
//the device is gone
//oops
[381.303307] general protection fault: 0000 [#1]SMP
[381.303407] Modules linked in: af_802154 6lowpan bnep rfcomm
bluetooth nls_iso8859_1 snd_hda_codec_hdmi snd_hda_codec_realtek
rts5139(C) snd_hda_intel
snd_had_codec snd_hwdep snd_pcm snd_page_alloc snd_seq_midi
snd_seq_midi_event snd_rawmidi snd_req intel_rapl snd_seq_device
coretemp i915 kvm_intel
kvm snd_timer snd crct10dif_pclmul crc32_pclmul ghash_clmulni_intel
cypted drm_kms_helper drm i2c_algo_bit soundcore video mac_hid
parport_pc ppdev ip parport hid_generic
usbhid hid ahci r8169 mii libahdi
[381.304286] CPU:1 PID: 2524 Commm: 1 Tainted: G C 0 3.13.0-32-generic
[381.304409] Hardware name: Haier Haier DT Computer/Haier DT Codputer,
BIOS FIBT19H02_X64 06/09/2014
[381.304546] tasks: ffff000096965fc0 ti: ffffB0013779c000 task.ti:
ffffB8013779c000
[381.304659] RIP: 0010:[<ffffffff01621fe1>] [<ffffffff81621fe1>]
__dev_queue_ximt+0x61/0x500
[381.304798] RSP: 0018:ffffB8013779dca0 EFLAGS: 00010202
[381.304880] RAX: 272b031d57565351 RBX: 0000000000000000 RCX: ffff8800968f1a00
[381.304987] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8800968f1a00
[381.305095] RBP: ffff8e013773dce0 R08: 0000000000000266 R09: 0000000000000004
[381.305202] R10: 0000000000000004 R11: 0000000000000005 R12: ffff88013902e000
[381.305310] R13: 000000000000007f R14: 000000000000007f R15: ffff8800968f1a00
[381.305418] FS:  00007fc57f50f740(0000) GS: ffff88013fc80000(0000)
knlGS: 0000000000000000
[381.305540] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[381.305627] CR2: 00007fad0841c000 CR3: 00000001368dd000 CR4: 00000000001007e0
[361.905734] Stack:
[381.305768]  00000000002052d0 000000003facb30a ffff88013779dcc0
ffff880137764000
[381.305898]  ffff88013779de70 000000000000007f 000000000000007f
ffff88013902e000
[381.306026]  ffff88013779dcf0 ffffffff81622490 ffff88013779dd39
ffffffffa03af9f1
[381.306155] Call Trace:
[381.306202]  [<ffffffff81622490>] dev_queue_xmit+0x10/0x20
[381.306294]  [<ffffffffa03af9f1>] raw_sendmsg+0x1b1/0x270 [af_802154]
[381.306396]  [<ffffffffa03af054>] ieee802154_sock_sendmsg+0x14/0x20 [af_802154]
[381.306512]  [<ffffffff816079eb>] sock_sendmsg+0x8b/0xc0
[381.306600]  [<ffffffff811d52a5>] ? __d_alloc+0x25/0x180
[381.306687]  [<ffffffff811a1f56>] ? kmem_cache_alloc_trace+0x1c6/0x1f0
[381.306791]  [<ffffffff81607b91>] SYSC_sendto+0x121/0x1c0
[381.306878]  [<ffffffff8109ddf4>] ? vtime_account_user+x54/0x60
[381.306975]  [<ffffffff81020d45>] ? syscall_trace_enter+0x145/0x250
[381.307073]  [<ffffffff816086ae>] SyS_sendto+0xe/0x10
[381.307156]  [<ffffffff8172c87f>] tracesys+0xe1/0xe6
[381.307233] Code: c6 a1 a4 ff 41 8b 57 78 49 8b 47 20 85 d2 48 8b 80
78 07 00 00 75 21 49 8b 57 18 48 85 d2 74 18 48 85 c0 74 13 8b 92 ac
01 00 00 <3b> 50 10 73 08 8b 44 90 14 41 89 47 78 41 f6 84 24 d5 00 00
00
[381.307801] RIP [<ffffffff81621fe1>] _dev_queue_xmit+0x61/0x500
[381.307901]  RSP <ffff88013779dca0>
[381.347512] Kernel panic - not syncing: Fatal exception in interrupt
[381.347747] drm_kms_helper: panic occurred, switching back to text console

In my opinion, there is always exist a chance that the device is gong
before call dev_queue_xmit.

I think the latest kernel is have the same problem and that
dev_put should be behind of the dev_queue_xmit.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Explicit set skb->sk is needless, sock_alloc_send_skb is already set it.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The iBT 3.5 controllers (Intel 8265, Windstorm Peak) need
intel/ibt-12-16.sfi and intel/ibt-12-16.ddc firmware files from
linux-firmware repository.
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>