- 09 Mar, 2018 4 commits
-
-
Uwe Kleine-König authored
Neither .dma_is_txing nor .dma_is_rxing can evaluate to true if .dma_is_enabled evaluates to false: The only function that sets .dma_is_txing to a non-zero value is imx_dma_tx() which is only called if .dma_is_enabled is true. Same for .dma_is_rxing and start_rx_dma(). And before .dma_is_enabled is set to 0 when imx_shutdown calls imx_disable_dma(), .dma_is_rxing and .dma_is_txing are reset to zero before, too. For this reason sport->dma_is_enabled && sport->dma_is_rxing has the same value as sport->dma_is_rxing which allows to simplify three if conditions. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
This reduces the amount of read accesses to the register space by shadowing the values for five registers that only change on writing them. There is a single bit in UCR2 that might change without being written to it, this is handled accordingly. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
This prepares implementing shadow copies for the control registers and additionally provides a good place to hook in debug code to trace register usage. Most of this patch was done using pattern substitution: perl -p -i -e ' s/\breadl(?:_relaxed)?\((?:sport->port\.|port->)membase \+/imx_uart_readl(sport,/; s/\bwritel(?:_relaxed)?\(([^,]*), (sport->port\.|port->)membase \+/imx_uart_writel(sport, $1,/; ' drivers/tty/serial/imx.c Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Palmer Dabbelt authored
The RISC-V ISA defines a simple console that is availiable via SBI calls on all systems. The SBI console is designed to be availiable at all times, so while it's most natural to use this as an early printk target it's also possible to use this as the system console when there isn't a better one availiable. This patch adds support for the RISC-V SBI console via the HVC infastructure. It's entirely independent from our early printk support, which results in early boot messages appearing twice over the SBI console. As far as I can tell that's the fault of our early printk support (we should support earlycon) as opposed to this driver. There is one checkpatch.pl warning here: to check the MAINTAINERS file. They're all matched by the "K: riscv" line. Signed-off-by: Palmer Dabbelt <palmer@sifive.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 28 Feb, 2018 29 commits
-
-
Uwe Kleine-König authored
Consistently indicate being called with irqs off and the port lock taken for all functions that this applies to. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
Only the reference manual for the i.MX1 (I have MC9328MX1RM/D Rev 5 from 2004) uses TDMAEN and RDMAEN for these. All reference manuals for the newer chips use TXDMAEN and RXDMAEN. Update to the newer name with the assumption that most imx users don't use an imx1 any more. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andy Shevchenko authored
PCI ID database is for IDs used across several drivers. Here is the case for SUNIX combo cards. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The cdns_uart_port[] array is indexed using a value derived from the "serialN" alias in DT, which may lead to an out-of-bounds access. Fix this by adding a range check. Fixes: 928e9263 ("tty: xuartps: Initialize ports according to aliases") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The sirf_ports[] array is indexed using a value derived from the "serialN" alias in DT, which may lead to an out-of-bounds access. Fix this by adding a range check. Fixes: a6ffe896 ("serial: sirf: use dynamic method allocate uart structure") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The sci_ports[] array is indexed using a value derived from the "serialN" alias in DT, which may lead to an out-of-bounds access. Fix this by adding a range check. Note that the array size is defined by a Kconfig symbol (CONFIG_SERIAL_SH_SCI_NR_UARTS), so this can even be triggered using a legitimate DTB. Fixes: 97ed9790 ("serial: sh-sci: Remove unused platform data capabilities field") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The s3c24xx_serial_ports[] array is indexed using a value derived from the "serialN" alias in DT, or from an incrementing probe index, which may lead to an out-of-bounds access. Fix this by adding a range check. Note that the array size is defined by a Kconfig symbol (CONFIG_SERIAL_SAMSUNG_UARTS), so this can even be triggered using a legitimate DTB or legitimate board code. Fixes: 13a9f6c6 ("serial: samsung: Consider DT alias when probing ports") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The serial_pxa_ports[] array is indexed using a value derived from the "serialN" alias in DT, or from platform data, which may lead to an out-of-bounds access. Fix this by adding a range check. Fixes: 699c20f3 ("serial: pxa: add OF support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The auart_port[] array is indexed using a value derived from the "serialN" alias in DT, or from platform data, which may lead to an out-of-bounds access. Fix this by adding a range check. Fixes: 1ea6607d ("serial: mxs-auart: Allow device tree probing") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The imx_ports[] array is indexed using a value derived from the "serialN" alias in DT, or from platform data, which may lead to an out-of-bounds access. Fix this by adding a range check. Fixes: ff05967a ("serial/imx: add of_alias_get_id() reference back") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The lpuart_ports[] array is indexed using a value derived from the "serialN" alias in DT, which may lead to an out-of-bounds access. Fix this by adding a range check. Fixes: c9e2e946 ("tty: serial: add Freescale lpuart driver support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Geert Uytterhoeven authored
The arc_uart_ports[] array is indexed using a value derived from the "serialN" alias in DT, which may lead to an out-of-bounds access. Fix this by adding a range check. Note that the array size is defined by a Kconfig symbol (CONFIG_SERIAL_ARC_NR_PORTS), so this can even be triggered using a legitimate DTB. Fixes: ea28fd56 ("serial/arc-uart: switch to devicetree based probing") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
imx_shutdown() calls imx_disable_dma if .dma_is_enabled. So after imx_shudown() completes, .dma_is_enabled is zero. For this reason .dma_is_enabled is also zero when imx_startup() is called. So the check for this variable being zero can be dropped. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
The .dma_is_inited member is only set to a value != 0 when the port's startup function calls imx_uart_dma_init(). On shutdown of the port imx_uart_dma_exit is called which sets the value back to 0. So .dma_is_inited is always 0 when imx_startup() is called (assuming .startup() and .shutdown() are correctly balanced) and the check for !sport->dma_is_inited can go away. This allows to replace .dma_is_inited by a variable local to imx_startup. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
Handling an irq that isn't enabled can have some undesired side effects. Some of these are mentioned in the newly introduced code comment. Some of the irq sources already had their handling right, some don't. Handle them all in the same consistent way. The change for USR1_RRDY and USR1_AGTIM drops the check for dma_is_enabled. This is correct as UCR1_RRDYEN and UCR2_ATEN are always off if dma is enabled. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
Now the variable holding the value of register USR1 is called usr1 instead of sts which is more straight forward. The same is also done for sts2 which is called usr2 now. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
The check sts & USR1_DTRD was just evaluated to true two lines above. So this change doesn't have any effect on the semantic of the driver. Fixes: 27e16501 ("serial: imx: implement DSR irq handling for DTE mode") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Colin Ian King authored
Bit pattern STAT_FRM_ERR is being bit-wise or'd twice; remove the redundant 2nd STAT_FRM_ERR Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Troy Kisky authored
This allows me to login after sending a break when service serial-getty@ttymxc0.service is running The "tty_insert_flip_char(port, 0, TTY_BREAK)" in clear_rx_errors fixes this by allowing the higher layers to see a break. Also, call uart_handle_break to handle possible "secure attention key." FYI: Martin said the ROM sdma firmware works with this patch, but external sdma firmware still does not send breaks on a i.mx6UL Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Tested-by: Martin Hicks <mort@bork.org> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joshua Scott authored
An issue has been observed on the Marvell Armada 38x serial port. Writes to UART_LCR can result in characters that are currently held in the TX FIFO being lost rather than sent, even if the userspace process has attempted to flush them. This is most visible when using the "resize" command (tested on Busybox), where we have observed the escape code for restoring cursor position becoming mangled. Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ulrich Hecht authored
High latencies of classic timers cause performance issues for high- speed serial transmissions. This patch transforms rx_timer into an hrtimer to reduce the minimum latency. Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vignesh R authored
omap_8250_throttle() is called when tty RX buffer is about to overflow and can no longer keep up with the rate at which UART is receiving data. So, the expectation of this callback, is that UART stops RX and asserts HW flow control to signal the sender to stop sending more data. omap_8250_throttle() disables RX FIFO interrupts thus FIFO is no longer serviced, leading to assertion of flow control once RX FIFO is full. But, this does not work when DMA is enabled as driver keeps queuing new RX DMA request in completion handler without brothering about throttling request made by the higher layer. This patch introduces a flag that can be used to determine whether or not to queue next RX DMA request based on throttling request. Without this patch, tty buffer overflows are reported at higher baudrates. Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vignesh R authored
Currently, data in RX FIFO is read based on UART_LSR register state even if RDI and RLSI interrupts are disabled in UART_IER register. This is because when IRQ handler is called due to TX FIFO empty event, RX FIFO is serviced based on UART_LSR register status instead of UART_IIR status. This defeats the purpose of disabling UART RX FIFO interrupts during throttling(see, omap_8250_throttle()) as IRQ handler continues to drain UART RX FIFO resulting in overflow of buffer at tty layer. Fix this by making sure that driver drains UART RX FIFO only when UART_IIR_RDI is set along with UART_LSR_BI or UART_LSR_DR bits. Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sergei Shtylyov authored
R-Car V3H (R8A77980) SoC has the R-Car gen3 compatible SCIF and HSCIF ports, so document the SoC specific bindings. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jan Kundrát authored
Some debugging tools (/sys/kernel/debug/gpio, `lsgpio`) use the gpio_chip's label for displaying an additional context. Right now, the information duplicates stuff which is already available from the parent's device. This is how e.g. `lsgpio`'s output looks like: GPIO chip: gpiochip2, "spi1.2", 16 GPIO lines Comparing the output of other GPIO expanders that I have available: gpiochip4: GPIOs 464-479, parent: spi/spi1.1, mcp23s17, can sleep: gpiochip5: GPIOs 448-463, parent: i2c/0-0020, pca9555, can sleep: gpiochip2: GPIOs 496-511, parent: spi/spi1.2, spi1.2, can sleep: This patch ensures that the type of the real HW device is shown instead of duplicating the SPI path: gpiochip2: GPIOs 496-511, parent: spi/spi1.2, MAX14830, can sleep: Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
The UART can be operated without an irq. In this case a timer is setup that regularily calls altera_uart_interrupt(). The receiving part depends on pp->imr having the bit ALTERA_UART_STATUS_RRDY_MSK set, otherwise altera_uart_rx_chars() is never called. So ensure that the bit gets set (disguised as ALTERA_UART_CONTROL_RRDY_MSK) by not returning early from altera_uart_startup() if port->irq is 0. This doesn't affect the hardware as the ALTERA_UART_CONTROL_RRDY_MSK bit isn't actually written to the control register. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
If the irq line of an altera UART device isn't used to report interrupts for this device the driver better ensures that this device doesn't pull this line to active state and so disturb the whatever might be connected to this line. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
Most register accesses in the altera driver honor port->regshift by using altera_uart_writel(). There are a few accesses however that were missed when the driver was converted to use port->regshift and some others were added later in commit 4d9d7d89 ("serial: altera_uart: add earlycon support"). Fixes: 2780ad42 ("tty: serial: altera_uart: Use port->regshift to store bus shift") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kees Cook authored
Commit 4fe505119778 ("console: Expand dummy functions for CFI") accidentally added "static" to newport_con instance of struct consw, while trying to normalize the declarations. This, however, needed to stay non-static as it has an extern. Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: 4fe505119778 ("console: Expand dummy functions for CFI") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 27 Feb, 2018 3 commits
-
-
Kees Cook authored
This expands the no-op dummy functions into full prototypes to avoid indirect call mismatches when running under Control Flow Integrity checking, like with Clang's -fsanitize=cfi. Co-Developed-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kees Cook authored
Reading the function declarations for the console callbacks lacks any hints as to what the arguments are. Instead of going and digging around in various implementations that may each only have a subset of the callbacks, name all the arguments in the declaration. This has no functional change. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kees Cook authored
As done in commit: 724ba8b3 ("console/dummy: leave .con_font_get set to NULL") This drops the dummy .con_font_get(), as it could leave arguments uninitialized. Cc: Thomas Winischhofer <thomas@winischhofer.net> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 26 Feb, 2018 4 commits
-
-
Linus Torvalds authored
-
git://github.com/jcmvbkbc/linux-xtensaLinus Torvalds authored
Pull Xtensa fixes from Max Filippov: "Two fixes for reserved memory/DMA buffers allocation in high memory on xtensa architecture - fix memory accounting when reserved memory is in high memory region - fix DMA allocation from high memory" * tag 'xtensa-20180225' of git://github.com/jcmvbkbc/linux-xtensa: xtensa: support DMA buffers in high memory xtensa: fix high memory/reserved memory collision
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A small set of fixes: - UAPI data type correction for hyperv - correct the cpu cores field in /proc/cpuinfo on CPU hotplug - return proper error code in the resctrl file system failure path to avoid silent subsequent failures - correct a subtle accounting issue in the new vector allocation code which went unnoticed for a while and caused suspend/resume failures" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations x86/topology: Fix function name in documentation x86/intel_rdt: Fix incorrect returned value when creating rdgroup sub-directory in resctrl file system x86/apic/vector: Handle vector release on CPU unplug correctly genirq/matrix: Handle CPU offlining proper x86/headers/UAPI: Use __u64 instead of u64 in <uapi/asm/hyperv.h>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fix from Thomas Gleixner: "A single commit which shuts up a bogus GCC-8 warning" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/oprofile: Fix bogus GCC-8 warning in nmi_setup()
-