Expose through debugfs device telemetry data for QAT GEN4 devices.

This allows to gather metrics about the performance and the utilization
of a device. In particular, statistics on (1) the utilization of the
PCIe channel, (2) address translation, when SVA is enabled and (3) the
internal engines for crypto and data compression.

If telemetry is supported by the firmware, the driver allocates a DMA
region and a circular buffer. When telemetry is enabled, through the
`control` attribute in debugfs, the driver sends to the firmware, via
the admin interface, the `TL_START` command. This triggers the device to
periodically gather telemetry data from hardware registers and write it
into the DMA memory region. The device writes into the shared region
every second.

The driver, every 500ms, snapshots the DMA shared region into the
circular buffer. This is then used to compute basic metric
(min/max/average) on each counter, every time the `device_data` attribute
is queried.

Telemetry counters are exposed through debugfs in the folder
/sys/kernel/debug/qat_<device>_<BDF>/telemetry.

For details, refer to debugfs-driver-qat_telemetry in Documentation/ABI.

This patch is based on earlier work done by Wojciech Ziemba.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Extend the admin interface with two new public APIs to enable
and disable the telemetry feature: adf_send_admin_tl_start() and
adf_send_admin_tl_stop().

The first, sends to the firmware, through the ICP_QAT_FW_TL_START
message, the IO address where the firmware will write telemetry
metrics and a list of ring pairs (maximum 4) to be monitored.
It returns the number of accelerators of each type supported by
this hardware. After this message is sent, the firmware starts
periodically reporting telemetry data using by writing into the
dma buffer specified as input.

The second, sends the admin message ICP_QAT_FW_TL_STOP
which stops the reporting of telemetry data.

This patch is based on earlier work done by Wojciech Ziemba.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

GET_DEV() macro expansion relies on struct pci_dev being defined.

Include <linux/pci.h> at adf_accel_devices.h.
Signed-off-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Damian Muszynski <damian.muszynski@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

No functional modification involved.

./drivers/crypto/intel/iaa/iaa_crypto_main.c:979:2-3: Unneeded semicolon.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7772Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Remove a stray newline in update_max_adecomp_delay_ns().
Reported-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

In order for shared workqeues to work properly, desc->priv should be
set to 0 rather than 1.  The need for this is described in commit
f5ccf55e (dmaengine/idxd: Re-enable kernel workqueue under DMA
API), so we need to make IAA consistent with IOMMU settings, otherwise
we get:

  [  141.948389] IOMMU: dmar15: Page request in Privilege Mode
  [  141.948394] dmar15: Invalid page request: 2000026a100101 ffffb167

Dedicated workqueues ignore this field and are unaffected.
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Create a script for comparing tcrypt speed test logs.
The script will systematically analyze differences item
by item and provide a summary (average).
This tool is useful for evaluating the stability of
cryptographic module algorithms and assisting with
performance optimization.

Please note that for such a comparison, stability depends
on whether we allow frequency to float or pin the frequency.

The script produces comparisons in two scenes:

1. For operations in seconds
================================================================================
rfc4106(gcm(aes)) (pcrypt(rfc4106(gcm_base(ctr(aes-generic),ghash-generic))))
                         encryption
--------------------------------------------------------------------------------
bit key | byte blocks | base ops    | new ops     | differ(%)
160     | 16          | 66439       | 63063       | -5.08
160     | 64          | 62220       | 57439       | -7.68
...
288     | 4096        | 15059       | 16278       | 8.09
288     | 8192        | 9043        | 9526        | 5.34
--------------------------------------------------------------------------------
average differ(%s)    | total_differ(%)
--------------------------------------------------------------------------------
5.70                  | -4.49
================================================================================

2. For avg cycles of operation
================================================================================
rfc4106(gcm(aes)) (pcrypt(rfc4106(gcm_base(ctr(aes-generic),ghash-generic))))
                         encryption
--------------------------------------------------------------------------------
bit key | byte blocks | base cycles | new cycles  | differ(%)
160     | 16          | 32500       | 35847       | 10.3
160     | 64          | 33175       | 45808       | 38.08
...
288     | 4096        | 131369      | 132132      | 0.58
288     | 8192        | 229503      | 234581      | 2.21
--------------------------------------------------------------------------------
average differ(%s)    | total_differ(%)
--------------------------------------------------------------------------------
8.41                  | -6.70
================================================================================
Signed-off-by: WangJinchao <wangjinchao@xfusion.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Provide an option in Inline IPsec configure mailbox to configure the
CPT_AF_LFX_CTL:CTX_ILEN for inline CPT LF attached to CPT RVU PF.
This is needed to set the ctx ilen to size of inbound SA for
HW errata IPBUCPT-38756. Not setting this would lead to new context's
not being fetched.

Also set FLR_FLUSH in CPT_LF_CTX_CTL for CPT LF's as workaround
for same errata.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Register errors interrupts for inline cptlf attached to PF driver
so that SMMU faults and other errors can be reported.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

HW has a errata that CPT HW may hit an issue, while processing CPT
instructions with CTX_VAL set and CTX_VAL not set. So, this patch
adds the code to always set the CTX_VAL as a workaround.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Updates CPT inbound inline IPsec configure mailbox to take
CPT credit threshold and bpid, which are introduced
in CN10KB.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

CPT LF must be reset and follow CPT LF disable sequence
suggested by HW team, when driver exits.
This patch adds code for the same.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Adds code to not execute CPT errata "when CPT_AF_DIAG[FLT_DIS] = 0 and a
CPT engine access to LLC/DRAM encounters  a fault/poison, a rare case
may result in unpredictable data being delivered to a CPT engine"
workaround on CN10KA B0/CN10KB HW as it is fixed on these chips.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

On CN10KA B0/CN10KB, CPT scatter gather format has modified
to support multi-seg in inline IPsec. Due to this CPT requires
new firmware and doesn't work with CN10KA0/A1 firmware. To make
HW works in backward compatibility mode or works with CN10KA0/A1
firmware, a bit(T106_MODE) is introduced in HW CSR.

This patch adds devlink parameter for configuring T106_MODE.
This patch also documents the devlink parameter under
Documentation/crypto/device_drivers.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Scatter Gather input format for CPT has changed on CN10KB/CN10KA B0 HW
to make it compatible with NIX Scatter Gather format to support SG mode
for inline IPsec. This patch modifies the code to make the driver works
for the same. This patch also enables CPT firmware load for these chips.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

CPT block reset in CPT PF erase all the CPT configuration which is
done in AF driver init. So, remove CPT block reset from CPT PF as
it is also being done in AF init and not required in PF.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When ecb is used to wrap an lskcipher, the statesize isn't set
correctly.  Fix this by making the simple instance creator set
the statesize.

Reported-by: syzbot+8ffb0839a24e9c6bfa76@syzkaller.appspotmail.com
Reported-by: Edward Adam Davis <eadavis@qq.com>
Fixes: 662ea18d ("crypto: skcipher - Make use of internal state")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

smatch warnings:
drivers/crypto/stm32/stm32-crc32.c:108 stm32_crc_get_next_crc() warn:
can 'crc' even be NULL?

Use list_first_entry_or_null instead of list_first_entry to retrieve
the first device registered.
The function list_first_entry always return a non NULL pointer even if
the list is empty. Hence checking if the pointer returned is NULL does
not tell if the list is empty or not.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202311281111.ou2oUL2i-lkp@intel.com/Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202311281111.ou2oUL2i-lkp@intel.com/Signed-off-by: Thomas Bourgoin <thomas.bourgoin@foss.st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add support for 420xx devices by including a new device driver that
supports such devices, updates to the firmware loader and capabilities.

Compared to 4xxx devices, 420xx devices have more acceleration engines
(16 service engines and 1 admin) and support the wireless cipher
algorithms ZUC and Snow 3G.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Co-developed-by: Dong Xie <dong.xie@intel.com>
Signed-off-by: Dong Xie <dong.xie@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Relocate the structures adf_fw_objs and adf_fw_config from the file
adf_4xxx_hw_data.c to the newly created adf_fw_config.h.

These structures will be used by new device drivers.

This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Move logic that is common between QAT GEN4 accelerators to the
qat_common folder. This includes addresses of CSRs, setters and
configuration logic.
When moved, functions and defines have been renamed from 4XXX to GEN4.

Code specific to the device is moved to the file adf_gen4_hw_data.c.
Code related to configuration is moved to the newly created
adf_gen4_config.c.

This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add accel_dev as parameter of the function uof_get_num_objs().
This is in preparation for the introduction of the QAT 420xx driver as
it will allow to reconfigure the ae_mask when a configuration that does
not require all AEs is loaded on the device.

This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Move the function get_service_enabled() from adf_4xxx_hw_data.c to
adf_cfg_services.c and rename it as adf_get_service_enabled().
This function is not specific to the 4xxx and will be used by
other QAT drivers.

This does not introduce any functional change.
Signed-off-by: Jie Wang <jie.wang@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Document the crypto engine on the SM7280 Platform.
Signed-off-by: Om Prakash Singh <quic_omprsing@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When the mpi_ec_ctx structure is initialized, some fields are not
cleared, causing a crash when referencing the field when the
structure was released. Initially, this issue was ignored because
memory for mpi_ec_ctx is allocated with the __GFP_ZERO flag.
For example, this error will be triggered when calculating the
Za value for SM2 separately.

Fixes: d58bb7e5 ("lib/mpi: Introduce ec implementation to MPI library")
Cc: stable@vger.kernel.org # v6.5
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

All devices compatible with SM8150 QCE (so SM8250 and newer) do not have
clock inputs (clocks are handled by secure firmware), so explicitly
disallow the clocks in the bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Binding marks several devices as compatible with IPQ4019 QCE.  They have
different number of clocks, thus the fallback does not define the
clock constraints per variant and each specific compatible should have
its clocks in if:then: section.

Add missing clocks description for IPQ9574 QCE.

Fixes: 1f5ce01d ("dt-bindings: crypto: qcom-qce: add SoC compatible string for ipq9574")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Define SET_RUNTIME_PM_OPS for StarFive TRNG driver.
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Add compatible string for StarFive JH8100 trng.
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The scheduled tasklet needs to be executed on device remove.

Fixes: fed93fb6 ("crypto: virtio - Handle dataq logic with tasklet")
Signed-off-by: wangyangxin <wangyangxin1@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch fixes following cleanup issues:
 - Missing instruction queue free on cleanup. This
   will lead to memory leak.
 - lfs->lfs_num is set to zero before cleanup, which
   will lead to improper cleanup.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.

To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().

Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>