Always return IRQ_HANDLED otherwise we could get our IRQ line disabled due
to many spurious IRQs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Trivial changes to commitlogs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

omap_i2c_dev is allocated with kzalloc(),
so we need not initialize b_hw to zero.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

that way we can ignore TX IRQs while in receiver
mode and ignore RX IRQs while in transmitter mode.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Remove unnecessary braces]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

that's a nice helper from drivers core which
will give us the exact IRQ number, instead
of a pointer to an IRQ resource.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

According to flow diagrams on OMAP TRMs,
we should ACK the IRQ as they happen.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Ack the stat OMAP_I2C_STAT_AL in case of arbitration lost]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

this will make sure that we execute at least once.
No functional changes otherwise.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

re-factor the common parts to a separate function,
so that code is easier to read and understand.

No functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Make it not depend on ISR's local variables
in order to make it easier to re-factor the
transmit data loop.
Also since we are waiting for XUDF(Transmitter underflow) just before
writing data lets not flag the underflow.
This is anyways going to go once we write
the data.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

While they do pretty much the same thing, there
are a few peculiarities. Specially WRT erratas,
it's best to split those out and re-factor the
read/write loop to another function which both
cases call.

This last part will be done on another patch.

While at that, also avoid an unncessary register
read since dev->fifo_len will always contain the
correct amount of data to be transferred.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

stat & BIT(1) is the same as BIT(1), so let's
simplify things a bit by removing "stat &" from
all omap_i2c_ack_stat() calls.

Code snippet (extremely simplified):

if (stat & NACK) {
        ...
        omap_i2c_ack_stat(dev, stat & NACK);
}

if (stat & RDR) {
        ...
        omap_i2c_ack_stat(dev, stat & RDR);
}

and so on. The tricky place is only WRT errata handling, for example:

if (*stat & (NACK | AL)) {
        omap_i2c_ack_stat(dev, *stat & (XRDY | XDR));
        ...
}

but in this case, the errata says we must clear XRDY and XDR if that
errata triggers, so if they just got enabled or not, it doesn't matter.

Another tricky place is RDR | RRDY (likewise for XDR | XRDY):

if (stat & (RDR | RRDY)) {
        ...
        omap_i2c_ack_stat(dev, stat & (RDR | RRDY));
}

again here there will be no issues because those IRQs never fire
simultaneously and one will only after after we have handled the
previous, that's because the same FIFO is used anyway and we won't shift
data into FIFO until we tell the IP "hey, I'm done with the FIFO, you
can shift more data"
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
[Added the explaination from the discurssion to the commit logs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

trivial patch to aid readability. No functional
changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

The patch intends to decrease the indentation level on the
data handling
by using the fact that else of if (dev->buf_len) is same as
if (!dev->buf_len)

if (dev->buf_len) {
	aaa;
} else {
	bbb;
	break;
}

to

if (!dev->buf_len) {
        bbb;
        break;
}
aaa;

Hence no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

trivial patch, no functional changes

If the fifo is disabled or fifo_size is 0 the num_bytes
is set to 1. Else it is set to fifo_size or in case of a
draining interrupt the remaining bytes in the buff stat.
So the zero check is redundant and can be safely optimised.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

that helps deleting some boiler plate code
and lets driver-core manage our resources
for us.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Still use i2c-gpio on boards which have a SoC with a TWI IP which
doesn't have clock stretching in transmission mode.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Add TWI nodes for atmel SoCs but keep i2c-gpio ones in order to let the
choice to the user in dts files.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nikolaus Voss <n.voss@weinmann.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nikolaus Voss <n.voss@weinmann.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

As indicated in the datasheet, TWD and TWCK must not be programmed as
open-drain.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nikolaus Voss <n.voss@weinmann.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

The G45 datasheets explicitly states that setting the open drain property
on peripheral function gpios is not allowed. (How about other A91 chips?)
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

This driver has the following properties compared to the old driver:
1. Support for multiple interfaces.
2. Interrupt driven I/O as opposed to polling/busy waiting.
3. Support for _one_ repeated start (Sr) condition, which is enough
   for most real-world applications including all SMBus transfer types.
   (The hardware does not support issuing arbitrary Sr conditions on the
    bus.)

testing: SoC: at91sam9g45
	 - BQ20Z80 battery SMBus client.
	 - on a 2.6.38 kernel with several i2c clients (temp-sensor,
	   audio-codec, touchscreen-controller, w1-bridge, io-expanders)
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Hubert Feurstein <h.feurstein@gmail.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>

[wsa: squashed with the following patches from Ludovic to have some flaws
fixed:
        i2c: at91: use managed resources
        i2c: at91: add warning about transmission issues for some devices
        i2c: at91: use an id table for SoC dependent parameters
]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

It will get replaced by a superior one. Safe to remove since this one
depends on BROKEN anyhow.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>

[wsa: added commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

The old driver used con_id clock entries. Convert to use dev_id
for clock lookup via standard method.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

The regulator fetched by the Nomadik I2C driver is actually a
voltage domain regulator. Stop doing this in the driver and
let the power domain code handle any regulators, as discussed
on the list.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

add of support for the davinci i2c driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

[wsa: fix indentation in the binding description]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Use dev_dbg logging style as it is done in other parts of this driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

It is useful information in dmesg to have a message indicating that the i2c
driver was succesfully registered, so promote it to dev_info.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

Pull DMA-mapping fixes from Marek Szyprowski:
 "Another set of fixes for ARM dma-mapping subsystem.

  Commit e9da6e99 replaced custom consistent buffer remapping code
  with generic vmalloc areas.  It however introduced some regressions
  caused by limited support for allocations in atomic context.  This
  series contains fixes for those regressions.

  For some subplatforms the default, pre-allocated pool for atomic
  allocations turned out to be too small, so a function for setting its
  size has been added.

  Another set of patches adds support for atomic allocations to
  IOMMU-aware DMA-mapping implementation.

  The last part of this pull request contains two fixes for Contiguous
  Memory Allocator, which relax too strict requirements."

* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
  ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
  ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
  ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
  ARM: dma-mapping: atomic_pool with struct page **pages
  ARM: Kirkwood: increase atomic coherent pool size
  ARM: DMA-Mapping: print warning when atomic coherent allocation fails
  ARM: DMA-Mapping: add function for setting coherent pool size from platform code
  ARM: relax conditions required for enabling Contiguous Memory Allocator
  mm: cma: fix alignment requirements for contiguous regions

Pull input subsystem updates from Dmitry Torokhov.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: wacom - add support for EMR on Cintiq 24HD touch
  Input: i8042 - add Gigabyte T1005 series netbooks to noloop table
  Input: imx_keypad - reset the hardware before enabling
  Input: edt-ft5x06 - fix build error when compiling wthout CONFIG_DEBUG_FS

Pull HID updates from Jiri Kosina:
 "It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
  performance improvement (not processing debug data if noone is
  interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
  work even with generic driver in a crippled mode, by Andres Freund."

* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
  HID: Only dump input if someone is listening
  HID: add NOGET quirk for Eaton Ellipse MAX UPS

c1dcad2d added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Merge tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 * Fix for TLB flushing introduced in v3.6
 * Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
   in a 32-bit kernel we need to allocate for coherent pages from a
   32-bit pool.
 * When trying to re-use P2M nodes we had a one-off error and triggered
   a BUG_ON check with specific CONFIG_ option.
 * When doing FLR in Xen-PCI-backend we would first do FLR then save the
   PCI configuration space. We needed to do it the other way around.

* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/pciback: Fix proper FLR steps.
  xen: Use correct masking in xen_swiotlb_alloc_coherent.
  xen: fix logical error in tlb flushing
  xen/p2m: Fix one-off error in checking the P2M tree directory.

Pull PCI updates from Bjorn Helgaas:
 "Power management
    - PCI/PM: Enable D3/D3cold by default for most devices
    - PCI/PM: Keep parent bridge active when probing device
    - PCI/PM: Fix config reg access for D3cold and bridge suspending
    - PCI/PM: Add ABI document for sysfs file d3cold_allowed
  Core
    - PCI: Don't print anything while decoding is disabled"

* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Don't print anything while decoding is disabled
  PCI/PM: Add ABI document for sysfs file d3cold_allowed
  PCI/PM: Fix config reg access for D3cold and bridge suspending
  PCI/PM: Keep parent bridge active when probing device
  PCI/PM: Enable D3/D3cold by default for most devices

Pull ARM SoC bug fixes from Olof Johansson:
 "Mostly Renesas and Atmel bugfixes this time, targeting boot and build
  problems.  A couple of patches for gemini and kirkwood as well.  On a
  whole nothing very controversial."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: gemini: fix the gemini build
  ARM: shmobile: armadillo800eva: enable rw rootfs mount
  ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
  ARM: shmobile: mackerel: fixup usb module order
  ARM: shmobile: armadillo800eva: fixup: sound card detection order
  ARM: shmobile: marzen: fixup smsc911x id for regulator
  ARM: at91/feature-removal-schedule: delay at91_mci removal
  ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
  ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
  ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
  ARM: at91/clock: fix PLLA overclock warning
  ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
  ARM: at91: fix system timer irq issue due to sparse irq support
  ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc

Pull a hwmon fix from Guenter Roeck:
 "One patch, fixing DIV_ROUND_CLOSEST to support negative dividends.

  While the changes are not in the drivers/hwmon directory, the problem
  primarily affects hwmon drivers, and it makes sense to push the patch
  through the hwmon tree."

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  linux/kernel.h: Fix DIV_ROUND_CLOSEST to support negative dividends

Pull kbuild fixes from Michal Marek:
 "These are two fixes that should go into 3.6.  The link-vmlinux.sh one
  is obvious.

  The other one fixes make firmware_install with certain configurations,
  where a file in the toplevel firmware tree gets installed first, and
  $(INSTALL_FW_PATH)/$$(dir <file>) results in /lib/firmware/./, which
  confuses make 3.82 for some reason."

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  firmware: fix directory creation rule matching with make 3.82
  link-vmlinux.sh: Fix stray "echo" in error message

Trivially triggerable, found by trinity:

  kernel BUG at mm/mempolicy.c:2546!
  Process trinity-child2 (pid: 23988, threadinfo ffff88010197e000, task ffff88007821a670)
  Call Trace:
    show_numa_map+0xd5/0x450
    show_pid_numa_map+0x13/0x20
    traverse+0xf2/0x230
    seq_read+0x34b/0x3e0
    vfs_read+0xac/0x180
    sys_pread64+0xa2/0xc0
    system_call_fastpath+0x1a/0x1f
  RIP: mpol_to_str+0x156/0x360

Cc: stable@vger.kernel.org
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When we do FLR and save PCI config we did it in the wrong order.
The end result was that if a PCI device was unbind from
its driver, then binded to xen-pciback, and then back to its
driver we would get:

> lspci -s 04:00.0
04:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
13:42:12 # 4 :~/
> echo "0000:04:00.0" > /sys/bus/pci/drivers/pciback/unbind
> modprobe e1000e
e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
e1000e 0000:04:00.0: Disabling ASPM L0s L1
e1000e 0000:04:00.0: enabling device (0000 -> 0002)
xen: registering gsi 48 triggering 0 polarity 1
Already setup the GSI :48
e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e: probe of 0000:04:00.0 failed with error -2

This fixes it by first saving the PCI configuration space, then
doing the FLR.
Reported-by: Ren, Yongjie <yongjie.ren@intel.com>
Reported-and-Tested-by: Tobias Geiger <tobias.geiger@vido.info>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org

Pull MMC fixes from Chris Ball:
 - a firmware bug on several Samsung MoviNAND eMMC models causes
   permanent corruption on the device when secure erase and secure trim
   requests are made, so we disable those requests on these eMMC devices.
 - atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
 - dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
   fix handling of error interrupts.
 - mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
 - omap: fix broken PIO mode causing memory corruption.
 - sdhci-esdhc: fix card detection.

* tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: omap: fix broken PIO mode
  mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
  mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
  mmc: dw_mmc: fix error handling in PIO mode
  mmc: dw_mmc: correct mishandling error interrupt
  mmc: dw_mmc: amend using error interrupt status
  mmc: atmel-mci: not busy flag has also to be used for read operations
  mmc: sdhci-esdhc: break out early if clock is 0
  mmc: mxs-mmc: fix deadlock caused by recursion loop
  mmc: mxs-mmc: fix deadlock in SDIO IRQ case
  mmc: bfin_sdh: fix dma_desc_array build error