- 20 Jan, 2022 40 commits
-
-
Ido Schimmel authored
The warning messages can be invoked from the data path for every packet transmitted through an ip6gre netdev, leading to high CPU utilization. Fix that by rate limiting the messages. Fixes: 09c6bbf0 ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime") Reported-by:
Maksym Yaremchuk <maksymy@nvidia.com> Tested-by:
Ido Schimmel <idosch@nvidia.com> Reviewed-by:
Amit Cohen <amcohen@nvidia.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Moshe Tal authored
The link extended sub-states are assigned as enum that is an integer size but read from a union as u8, this is working for small values on little endian systems but for big endian this always give 0. Fix the variable in the union to match the enum size. Fixes: ecc31c60 ("ethtool: Add link extended state") Signed-off-by:
Moshe Tal <moshet@nvidia.com> Reviewed-by:
Gal Pressman <gal@nvidia.com> Reviewed-by:
-
Robert Hancock authored
A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which is a 1 Gbps copper module operating in SGMII mode with an internal BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the module would work properly on the initial insertion or boot of the device, but after the device was rebooted, the link would either only come up at 100 Mbps speeds or go up and down erratically. I found no meaningful changes in the PHY configuration registers between the working and non-working boots, but the status registers seemed to have a lot of error indications set on the SERDES side of the device on the non-working boot. I suspect the problem is that whatever happens on the SGMII link when the device is rebooted and the FPGA logic gets reloaded ends up putting the module's onboard PHY into a bad state. Since commit 6e2d85ec ("net: phy: Stop with excessive soft reset") the genphy_soft_reset call is not made automatically by the PHY core unless the callback is explicitly specified in the driver structure. For most of these Broadcom devices, there is probably a hardware reset that gets asserted to reset the PHY during boot, however for SFP modules (where the BCM54616S is commonly found) no such reset line exists, so if the board keeps the SFP cage powered up across a reboot, it will end up with no reset occurring during reboots. Hook up the genphy_soft_reset callback for BCM54616S to ensure that a PHY reset is performed before the device is initialized. This appears to fix the issue with erratic operation after a reboot with this SFP module. Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset") Signed-off-by:
Robert Hancock <robert.hancock@calian.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Victor Nogueira authored
When adding a tc rule with a qdisc kind that is not supported or not compiled into the kernel, the kernel emits the following error: "Error: Specified qdisc not found.". Found via tdc testing when ETS qdisc was not compiled in and it was not obvious right away what the message meant without looking at the kernel code. Change the error message to be more explicit and say the qdisc kind is unknown. Signed-off-by:
Victor Nogueira <victor@mojatatu.com> Signed-off-by:
-
Congyu Liu authored
In one net namespace, after creating a packet socket without binding it to a device, users in other net namespaces can observe the new `packet_type` added by this packet socket by reading `/proc/net/ptype` file. This is minor information leakage as packet socket is namespace aware. Add a net pointer in `packet_type` to keep the net namespace of of corresponding packet socket. In `ptype_seq_show`, this net pointer must be checked when it is not NULL. Fixes: 2feb27db ("[NETNS]: Minor information leak via /proc/net/ptype file.") Signed-off-by:
Congyu Liu <liu3101@purdue.edu> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Including fixes from netfilter, bpf. Quite a handful of old regression fixes but most of those are pre-5.16. Current release - regressions: - fix memory leaks in the skb free deferral scheme if upper layer protocols are used, i.e. in-kernel TCP readers like TLS Current release - new code bugs: - nf_tables: fix NULL check typo in _clone() functions - change the default to y for Vertexcom vendor Kconfig - a couple of fixes to incorrect uses of ref tracking - two fixes for constifying netdev->dev_addr Previous releases - regressions: - bpf: - various verifier fixes mainly around register offset handling when passed to helper functions - fix mount source displayed for bpffs (none -> bpffs) - bonding: - fix extraction of ports for connection hash calculation - fix bond_xmit_broadcast return value when some devices are down - phy: marvell: add Marvell specific PHY loopback - sch_api: don't skip qdisc attach on ingress, prevent ref leak - htb: restore minimal packet size handling in rate control - sfp: fix high power modules without diagnostic monitoring - mscc: ocelot: - don't let phylink re-enable TX PAUSE on the NPI port - don't dereference NULL pointers with shared tc filters - smsc95xx: correct reset handling for LAN9514 - cpsw: avoid alignment faults by taking NET_IP_ALIGN into account - phy: micrel: use kszphy_suspend/_resume for irq aware devices, avoid races with the interrupt Previous releases - always broken: - xdp: check prog type before updating BPF link - smc: resolve various races around abnormal connection termination - sit: allow encapsulated IPv6 traffic to be delivered locally - axienet: fix init/reset handling, add missing barriers, read the right status words, stop queues correctly - add missing dev_put() in sock_timestamping_bind_phc() Misc: - ipv4: prevent accidentally passing RTO_ONLINK to ip_route_output_key_hash() by sanitizing flags - ipv4: avoid quadratic behavior in netns dismantle - stmmac: dwmac-oxnas: add support for OX810SE - fsl: xgmac_mdio: add workaround for erratum A-009885" * tag 'net-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (92 commits) ipv4: add net_hash_mix() dispersion to fib_info_laddrhash keys ipv4: avoid quadratic behavior in netns dismantle net/fsl: xgmac_mdio: Fix incorrect iounmap when removing module powerpc/fsl/dts: Enable WA for erratum A-009885 on fman3l MDIO buses dt-bindings: net: Document fsl,erratum-a009885 net/fsl: xgmac_mdio: Add workaround for erratum A-009885 net: mscc: ocelot: fix using match before it is set net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices net: cpsw: avoid alignment faults by taking NET_IP_ALIGN into account nfc: llcp: fix NULL error pointer dereference on sendmsg() after failed bind() net: axienet: increase default TX ring size to 128 net: axienet: fix for TX busy handling net: axienet: fix number of TX ring slots for available check net: axienet: Fix TX ring slot available check net: axienet: limit minimum TX ring size net: axienet: add missing memory barriers net: axienet: reset core on initialization prior to MDIO access net: axienet: Wait for PhyRstCmplt after core reset net: axienet: increase reset timeout bpf, selftests: Add ringbuf memory type confusion test ... -
Linus Torvalds authored
Merge more updates from Andrew Morton: "55 patches. Subsystems affected by this patch series: percpu, procfs, sysctl, misc, core-kernel, get_maintainer, lib, checkpatch, binfmt, nilfs2, hfs, fat, adfs, panic, delayacct, kconfig, kcov, and ubsan" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (55 commits) lib: remove redundant assignment to variable ret ubsan: remove CONFIG_UBSAN_OBJECT_SIZE kcov: fix generic Kconfig dependencies if ARCH_WANTS_NO_INSTR lib/Kconfig.debug: make TEST_KMOD depend on PAGE_SIZE_LESS_THAN_256KB btrfs: use generic Kconfig option for 256kB page size limit arch/Kconfig: split PAGE_SIZE_LESS_THAN_256KB from PAGE_SIZE_LESS_THAN_64KB configs: introduce debug.config for CI-like setup delayacct: track delays from memory compact Documentation/accounting/delay-accounting.rst: add thrashing page cache and direct compact delayacct: cleanup flags in struct task_delay_info and functions use it delayacct: fix incomplete disable operation when switch enable to disable delayacct: support swapin delay accounting for swapping without blkio panic: remove oops_id panic: use error_report_end tracepoint on warnings fs/adfs: remove unneeded variable make code cleaner FAT: use io_schedule_timeout() instead of congestion_wait() hfsplus: use struct_group_attr() for memcpy() region nilfs2: remove redundant pointer sbufs fs/binfmt_elf: use PT_LOAD p_align values for static PIE const_structs.checkpatch: add frequently used ops structs ...
-
Colin Ian King authored
The variable ret is being assigned a value that is never read. If the for-loop is entered then ret is immediately re-assigned a new value. If the for-loop is not executed ret is never read. The assignment is redundant and can be removed. Link: https://lkml.kernel.org/r/20211230134557.83633-1-colin.i.king@gmail.comSigned-off-by:
Colin Ian King <colin.i.king@gmail.com> Reviewed-by:
Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Kees Cook authored
The object-size sanitizer is redundant to -Warray-bounds, and inappropriately performs its checks at run-time when all information needed for the evaluation is available at compile-time, making it quite difficult to use: https://bugzilla.kernel.org/show_bug.cgi?id=214861 With -Warray-bounds almost enabled globally, it doesn't make sense to keep this around. Link: https://lkml.kernel.org/r/20211203235346.110809-1-keescook@chromium.orgSigned-off-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Marco Elver <elver@google.com> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Michal Marek <michal.lkml@markovi.net> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Marco Elver authored
Until recent versions of GCC and Clang, it was not possible to disable KCOV instrumentation via a function attribute. The relevant function attribute was introduced in 540540d0 ("kcov: add __no_sanitize_coverage to fix noinstr for all architectures"). x86 was the first architecture to want a working noinstr, and at the time no compiler support for the attribute existed yet. Therefore, commit 0f1441b4 ("objtool: Fix noinstr vs KCOV") introduced the ability to NOP __sanitizer_cov_*() calls in .noinstr.text. However, this doesn't work for other architectures like arm64 and s390 that want a working noinstr per ARCH_WANTS_NO_INSTR. At the time of 0f1441b4, we didn't yet have ARCH_WANTS_NO_INSTR, but now we can move the Kconfig dependency checks to the generic KCOV option. KCOV will be available if: - architecture does not care about noinstr, OR - we have objtool support (like on x86), OR - GCC is 12.0 or newer, OR - Clang is 13.0 or newer. Link: https://lkml.kernel.org/r/20211201152604.3984495-1-elver@google.comSigned-off-by:
Nathan Chancellor <nathan@kernel.org> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by:
-
Nathan Chancellor authored
Commit b05fbcc3 ("btrfs: disable build on platforms having page size 256K") disabled btrfs for configurations that used a 256kB page size. However, it did not fully solve the problem because CONFIG_TEST_KMOD selects CONFIG_BTRFS, which does not account for the dependency. This results in a Kconfig warning and the failed BUILD_BUG_ON error returning. WARNING: unmet direct dependencies detected for BTRFS_FS Depends on [n]: BLOCK [=y] && !PPC_256K_PAGES && !PAGE_SIZE_256KB [=y] Selected by [m]: - TEST_KMOD [=m] && RUNTIME_TESTING_MENU [=y] && m && MODULES [=y] && NETDEVICES [=y] && NET_CORE [=y] && INET [=y] && BLOCK [=y] To resolve this, add CONFIG_PAGE_SIZE_LESS_THAN_256KB as a dependency of CONFIG_TEST_KMOD so there is no more invalid configuration or build errors. Link: https://lkml.kernel.org/r/20211129230141.228085-4-nathan@kernel.org Fixes: b05fbcc3 ("btrfs: disable build on platforms having page size 256K") Signed-off-by:
kernel test robot <lkp@intel.com> Cc: Chris Mason <clm@fb.com> Cc: David Sterba <dsterba@suse.com> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
-
Nathan Chancellor authored
Use the newly introduced CONFIG_PAGE_SIZE_LESS_THAN_256KB to describe the dependency introduced by commit b05fbcc3 ("btrfs: disable build on platforms having page size 256K"). Link: https://lkml.kernel.org/r/20211129230141.228085-3-nathan@kernel.orgSigned-off-by:
David Sterba <dsterba@suse.com> Cc: Chris Mason <clm@fb.com> Cc: Josef Bacik <josef@toxicpanda.com> Cc: kernel test robot <lkp@intel.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
-
Nathan Chancellor authored
Patch series "Fix CONFIG_TEST_KMOD with 256kB page size". The kernel test robot reported a build error [1] from a failed assertion in fs/btrfs/inode.c with a hexagon randconfig that includes CONFIG_PAGE_SIZE_256KB. This error is the same one that was addressed by commit b05fbcc3 ("btrfs: disable build on platforms having page size 256K") but CONFIG_TEST_KMOD selects CONFIG_BTRFS without having the "page size less than 256kB dependency", which results in the error reappearing. The first patch introduces CONFIG_PAGE_SIZE_LESS_THAN_256KB by splitting it off from CONFIG_PAGE_SIZE_LESS_THAN_64KB, which was introduced in commit 1f0e290c ("arch: Add generic Kconfig option indicating page size smaller than 64k") for a similar reason in 5.16-rc3. The second patch uses that configuration option for CONFIG_BTRFS to reduce duplication. The third patch resolves the build error by adding CONFIG_PAGE_SIZE_LESS_THAN_256KB as a dependency to CONFIG_TEST_KMOD so that CONFIG_BTRFS does not get enabled under that invalid configuration. [1]: https://lore.kernel.org/r/202111270255.UYOoN5VN-lkp@intel.com/ This patch (of 3): btrfs requires a page size smaller than 256kB. To use that dependency in other places, introduce CONFIG_PAGE_SIZE_LESS_THAN_256KB and reuse that dependency in CONFIG_PAGE_SIZE_LESS_THAN_64KB. Link: https://lkml.kernel.org/r/20211129230141.228085-1-nathan@kernel.org Link: https://lkml.kernel.org/r/20211129230141.228085-2-nathan@kernel.orgSigned-off-by:
-
Qian Cai authored
Some general debugging features like kmemleak, KASAN, lockdep, UBSAN etc help fix many viruses like a microscope. On the other hand, those features are scatter around and mixed up with more situational debugging options making them difficult to consume properly. This cold help amplify the general debugging/testing efforts and help establish sensitive default values for those options across the broad. This could also help different distros to collaborate on maintaining debug-flavored kernels. The config is based on years' experiences running daily CI inside the largest enterprise Linux distro company to seek regressions on linux-next builds on different bare-metal and virtual platforms. It can be used for example, $ make ARCH=arm64 defconfig debug.config Since KASAN and KCSAN can't be enabled together, we will need to create a separate one for KCSAN later as well. Link: https://lkml.kernel.org/r/20211115134754.7334-1-quic_qiancai@quicinc.comSigned-off-by:
Qian Cai <quic_qiancai@quicinc.com> Acked-by:
Paul E. McKenney <paulmck@kernel.org> Cc: Marco Elver <elver@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: "Stephen Rothwell" <sfr@canb.auug.org.au> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
wangyong authored
Delay accounting does not track the delay of memory compact. When there is not enough free memory, tasks can spend a amount of their time waiting for compact. To get the impact of tasks in direct memory compact, measure the delay when allocating memory through memory compact. Also update tools/accounting/getdelays.c: / # ./getdelays_next -di -p 304 print delayacct stats ON printing IO accounting PID 304 CPU count real total virtual total delay total delay average 277 780000000 849039485 18877296 0.068ms IO count delay total delay average 0 0 0ms SWAP count delay total delay average 0 0 0ms RECLAIM count delay total delay average 5 11088812685 2217ms THRASHING count delay total delay average 0 0 0ms COMPACT count delay total delay average 3 72758 0ms watch: read=0, write=0, cancelled_write=0 Link: https://lkml.kernel.org/r/1638619795-71451-1-git-send-email-wang.yong12@zte.com.cnSigned-off-by:wangyong <wang.yong12@zte.com.cn> Reviewed-by:
Jiang Xuexin <jiang.xuexin@zte.com.cn> Reviewed-by:
Zhang Wenya <zhang.wenya1@zte.com.cn> Reviewed-by:
Yang Yang <yang.yang29@zte.com.cn> Reviewed-by:
Balbir Singh <bsingharora@gmail.com> Signed-off-by:
-
wangyong authored
Add thrashing page cache and direct compact related descriptions and update the usage of getdelays userspace utility. The following patches modifications have been updated: https://lore.kernel.org/all/20190312102002.31737-4-jinpuwang@gmail.com/ https://lore.kernel.org/all/1638619795-71451-1-git-send-email- wang.yong12@zte.com.cn/ Link: https://lkml.kernel.org/r/1639583021-92977-1-git-send-email-wang.yong12@zte.com.cnSigned-off-by:
Zeal Robot <zealci@zte.com.cn> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Yang Yang authored
Flags in struct task_delay_info is used to distinguish the difference between swapin and blkio delay acountings. But after patch "delayacct: support swapin delay accounting for swapping without blkio", there is no need to do that since swapin and blkio delay accounting use their own functions. Link: https://lkml.kernel.org/r/20211124065958.36703-1-yang.yang29@zte.com.cnSigned-off-by:
-
Yang Yang authored
When a task is created after delayacct is enabled, kernel will do all the delay accountings for that task. The problems is if user disables delayacct by set /proc/sys/kernel/task_delayacct to zero, only blkio delay accounting is disabled. Now disable all the kinds of delay accountings when /proc/sys/kernel/task_delayacct sets to zero. Link: https://lkml.kernel.org/r/20211123140342.32962-1-ran.xiaokai@zte.com.cnSigned-off-by:
-
Yang Yang authored
Currently delayacct accounts swapin delay only for swapping that cause blkio. If we use zram for swapping, tools/accounting/getdelays can't get any SWAP delay. It's useful to get zram swapin delay information, for example to adjust compress algorithm or /proc/sys/vm/swappiness. Reference to PSI, it accounts any kind of swapping by doing its work in swap_readpage(), no matter whether swapping causes blkio. Let delayacct do the similar work. Link: https://lkml.kernel.org/r/20211112083813.8559-1-yang.yang29@zte.com.cnSigned-off-by:
-
Sebastian Andrzej Siewior authored
The oops id has been added as part of the end of trace marker for the kerneloops.org project. The id is used to automatically identify duplicate submissions of the same report. Identical looking reports with different a id can be considered as the same oops occurred again. The early initialisation of the oops_id can create a warning if the random core is not yet fully initialized. On PREEMPT_RT it is problematic if the id is initialized on demand from non preemptible context. The kernel oops project is not available since 2017. Remove the oops_id and use 0 in the output in case parser rely on it. Link: https://bugs.debian.org/953172 Link: https://lkml.kernel.org/r/Ybdi16aP2NEugWHq@linutronix.deSigned-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by:
-
Marco Elver authored
Introduce the error detector "warning" to the error_report event and use the error_report_end tracepoint at the end of a warning report. This allows in-kernel tests but also userspace to more easily determine if a warning occurred without polling kernel logs. [akpm@linux-foundation.org: add comma to enum list, per Andy] Link: https://lkml.kernel.org/r/20211115085630.1756817-1-elver@google.comSigned-off-by:
-
Minghao Chi authored
Return value directly instead of taking this in a variable. Link: https://lkml.kernel.org/r/20211210023211.424609-1-chi.minghao@zte.com.cnSigned-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Reported-by:
Zeal Robot <zealci@zte.com.cm> Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: Jan Kara <jack@suse.cz> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
NeilBrown authored
congestion_wait() in this context is just a sleep - block devices do not support congestion signalling any more. The goal for this wait, which was introduced in commit ae78bf9c ("[PATCH] add -o flush for fat") is to wait for any recently written data to get to storage. We currently have no direct mechanism to do this, so a simple wait that behaves identically to the current congestion_wait() is the best we can do. This is a step towards removing congestion_wait() Link: https://lkml.kernel.org/r/163936544519.22433.13400436295732112065@noble.neil.brown.nameSigned-off-by:
NeilBrown <neilb@suse.de> Acked-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by:
-
Kees Cook authored
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memset(), avoid intentionally writing across neighboring fields. Add struct_group() to mark the "info" region (containing struct DInfo and struct DXInfo structs) in struct hfsplus_cat_folder and struct hfsplus_cat_file that are written into directly, so the compiler can correctly reason about the expected size of the writes. "pahole" shows no size nor member offset changes to struct hfsplus_cat_folder nor struct hfsplus_cat_file. "objdump -d" shows no object code changes. Link: https://lkml.kernel.org/r/20211119192851.1046717-1-keescook@chromium.orgSigned-off-by:
Christian Brauner <christian.brauner@ubuntu.com> Cc: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by:
-
Colin Ian King authored
Pointer sbufs is being assigned a value but it's not being used later on. The pointer is redundant and can be removed. Cleans up scan-build static analysis warning: fs/nilfs2/page.c:203:8: warning: Although the value stored to 'sbufs' is used in the enclosing expression, the value is never actually read from 'sbufs' [deadcode.DeadStores] sbh = sbufs = page_buffers(src); Link: https://lkml.kernel.org/r/20211211180955.550380-1-colin.i.king@gmail.com Link: https://lkml.kernel.org/r/1640712476-15136-1-git-send-email-konishi.ryusuke@gmail.comSigned-off-by:Ryusuke Konishi <konishi.ryusuke@gmail.com> Signed-off-by:
-
H.J. Lu authored
Extend commit ce81bb25 ("fs/binfmt_elf: use PT_LOAD p_align values for suitable start address") which fixed PIE binaries built with -Wl,-z,max-page-size=0x200000, to cover static PIE binaries. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=215275 Tested by verifying static PIE binaries with -Wl,-z,max-page-size=0x200000 loading. Link: https://lkml.kernel.org/r/20211209174052.370537-1-hjl.tools@gmail.comSigned-off-by:
H.J. Lu <hjl.tools@gmail.com> Cc: Chris Kennelly <ckennelly@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Song Liu <songliubraving@fb.com> Cc: David Rientjes <rientjes@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Sandeep Patil <sspatil@google.com> Cc: Fangrui Song <maskray@google.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by:
-
Rikard Falkeborn authored
Add commonly used structs (>50 instances) which are always or almost always const. Link: https://lkml.kernel.org/r/20211127101134.33101-1-rikard.falkeborn@gmail.comSigned-off-by:
Rikard Falkeborn <rikard.falkeborn@gmail.com> Cc: Joe Perches <joe@perches.com> Signed-off-by:
-
Joe Perches authored
The Kconfig help test erroneously counts patch context lines as part of the help text. Fix that and improve the message block output. Link: https://lkml.kernel.org/r/06c0cdc157ae1502e8e9eb3624b9ea995cf11e7a.camel@perches.comSigned-off-by:
Joe Perches <joe@perches.com> Tested-by:
Randy Dunlap <rdunlap@infradead.org> Acked-by:
-
Jerome Forissier authored
One exceptions to the COMMIT_LOG_LONG_LINE rule is a file path followed by ':'. That is typically some sort diagnostic message from a compiler or a build tool, in which case we don't want to wrap the lines but keep the message unmodified. The regular expression used to match this pattern currently doesn't accept absolute paths or + characters. This can result in false positives as in the following (out-of-tree) example: ... /home/jerome/work/optee_repo_qemu/build/../toolchains/aarch32/bin/arm-linux-gnueabihf-ld.bfd: /home/jerome/work/toolchains-gcc10.2/aarch32/bin/../lib/gcc/arm-none-linux-gnueabihf/10.2.1/../../../../arm-none-linux-gnueabihf/lib/libstdc++.a(eh_alloc.o): in function `__cxa_allocate_exception': /tmp/dgboter/bbs/build03--cen7x86_64/buildbot/cen7x86_64--arm-none-linux-gnueabihf/build/src/gcc/libstdc++-v3/libsupc++/eh_alloc.cc:284: undefined reference to `malloc' ... Update the regular expression to match the above paths. Link: https://lkml.kernel.org/r/20210923143842.2837983-1-jerome@forissier.orgSigned-off-by:
Jerome Forissier <jerome@forissier.org> Acked-by:
-
Andrey Konovalov authored
Make do_kmem_cache_size_bulk() destroy the cache it creates. Link: https://lkml.kernel.org/r/aced20a94bf04159a139f0846e41d38a1537debb.1640018297.git.andreyknvl@google.com Fixes: 03a9349a ("lib/test_meminit: add a kmem_cache_alloc_bulk() test") Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Reviewed-by:
-
Andy Shevchenko authored
Remove licence boilerplate text from the UAPI header. Link: https://lkml.kernel.org/r/20211216113552.81199-2-andriy.shevchenko@linux.intel.comSigned-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Andy Shevchenko authored
Discourage people from using UAPI header in new code by adding a note. Link: https://lkml.kernel.org/r/20211216113552.81199-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Andy Shevchenko authored
When kernel.h is used in the headers it adds a lot into dependency hell, especially when there are circular dependencies are involved. Replace kernel.h inclusion with the list of what is really being used. Link: https://lkml.kernel.org/r/20211213204441.56204-1-andriy.shevchenko@linux.intel.comSigned-off-by:
Brendan Higgins <brendanhiggins@google.com> Tested-by:
-
Isabella Basso authored
Use KUnit framework to make tests more easily integrable with CIs. Even though these tests are not yet properly written as unit tests this change should help in debugging. Also remove kernel messages (i.e. through pr_info) as KUnit handles all debugging output and let it handle module init and exit details. Link: https://lkml.kernel.org/r/20211208183711.390454-6-isabbasso@riseup.netReviewed-by:
David Gow <davidgow@google.com> Reported-by:
Augusto Durães Camargo <augusto.duraes33@gmail.com> Signed-off-by:
Enzo Ferreira <ferreiraenzoa@gmail.com> Signed-off-by:
Isabella Basso <isabbasso@riseup.net> Cc: Brendan Higgins <brendanhiggins@google.com> Cc: Daniel Latypov <dlatypov@google.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Cc: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by:
-
Isabella Basso authored
Split TEST_HASH so that each entry only has one file. Note that there's no stringhash test file, but actually <linux/stringhash.h> tests are performed in lib/test_hash.c. Link: https://lkml.kernel.org/r/20211208183711.390454-5-isabbasso@riseup.netReviewed-by:
-
Isabella Basso authored
Split up test_hash_init so that it calls each test more explicitly insofar it is possible without rewriting the entire file. This aims at improving readability. Split tests performed on string_or as they don't interfere with those performed in hash_or. Also separate pr_info calls about skipped tests as they're not part of the tests themselves, but only warn about (un)defined arch-specific hash functions. Link: https://lkml.kernel.org/r/20211208183711.390454-4-isabbasso@riseup.netReviewed-by:
-
Isabella Basso authored
Split the test_int_hash function to keep its mainloop separate from arch-specific chunks, which are only compiled as needed. This aims at improving readability. Link: https://lkml.kernel.org/r/20211208183711.390454-3-isabbasso@riseup.netReviewed-by:
-
Isabella Basso authored
Patch series "test_hash.c: refactor into KUnit", v3. We refactored the lib/test_hash.c file into KUnit as part of the student group LKCAMP [1] introductory hackathon for kernel development. This test was pointed to our group by Daniel Latypov [2], so its full conversion into a pure KUnit test was our goal in this patch series, but we ran into many problems relating to it not being split as unit tests, which complicated matters a bit, as the reasoning behind the original tests is quite cryptic for those unfamiliar with hash implementations. Some interesting developments we'd like to highlight are: - In patch 1/5 we noticed that there was an unused define directive that could be removed. - In patch 4/5 we noticed how stringhash and hash tests are all under the lib/test_hash.c file, which might cause some confusion, and we also broke those kernel config entries up. Overall KUnit developments have been made in the other patches in this series: In patches 2/5, 3/5 and 5/5 we refactored the lib/test_hash.c file so as to make it more compatible with the KUnit style, whilst preserving the original idea of the maintainer who designed it (i.e. George Spelvin), which might be undesirable for unit tests, but we assume it is enough for a first patch. This patch (of 5): Currently, there exist hash_32() and __hash_32() functions, which were introduced in a patch [1] targeting architecture specific optimizations. These functions can be overridden on a per-architecture basis to achieve such optimizations. They must set their corresponding define directive (HAVE_ARCH_HASH_32 and HAVE_ARCH__HASH_32, respectively) so that header files can deal with these overrides properly. As the supported 32-bit architectures that have their own hash function implementation (i.e. m68k, Microblaze, H8/300, pa-risc) have only been making use of the (more general) __hash_32() function (which only lacks a right shift operation when compared to the hash_32() function), remove the define directive corresponding to the arch-specific hash_32() implementation. [1] https://lore.kernel.org/lkml/20160525073311.5600.qmail@ns.sciencehorizons.net/ [akpm@linux-foundation.org: hash_32_generic() becomes hash_32()] Link: https://lkml.kernel.org/r/20211208183711.390454-1-isabbasso@riseup.net Link: https://lkml.kernel.org/r/20211208183711.390454-2-isabbasso@riseup.netReviewed-by:
-
Zhen Lei authored
Currently, the entry->prev and entry->next are considered to be valid as long as they are not LIST_POISON{1|2}. However, the memory may be corrupted. The prev->next is invalid probably because 'prev' is invalid, not because prev->next's content is illegal. Unfortunately, the printk and its subfunctions will modify the registers that hold the 'prev' and 'next', and we don't see this valuable information in the BUG context. So print the contents of 'entry->prev' and 'entry->next'. Here's an example: list_del corruption. prev->next should be c0ecbf74, but was c08410dc kernel BUG at lib/list_debug.c:53! ... ... PC is at __list_del_entry_valid+0x58/0x98 LR is at __list_del_entry_valid+0x58/0x98 psr: 60000093 sp : c0ecbf30 ip : 00000000 fp : 00000001 r10: c08410d0 r9 : 00000001 r8 : c0825e0c r7 : 20000013 r6 : c08410d0 r5 : c0ecbf74 r4 : c0ecbf74 r3 : c0825d08 r2 : 00000000 r1 : df7ce6f4 r0 : 00000044 ... ... Stack: (0xc0ecbf30 to 0xc0ecc000) bf20: c0ecbf74 c0164fd0 c0ecbf70 c0165170 bf40: c0eca000 c0840c00 c0840c00 c0824500 c0825e0c c0189bbc c088f404 60000013 bf60: 60000013 c0e85100 000004ec 00000000 c0ebcdc0 c0ecbf74 c0ecbf74 c0825d08 bf80: c0e807c0 c018965c 00000000 c013f2a0 c0e807c0 c013f154 00000000 00000000 bfa0: 00000000 00000000 00000000 c01001b0 00000000 00000000 00000000 00000000 bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 (__list_del_entry_valid) from (__list_del_entry+0xc/0x20) (__list_del_entry) from (finish_swait+0x60/0x7c) (finish_swait) from (rcu_gp_kthread+0x560/0xa20) (rcu_gp_kthread) from (kthread+0x14c/0x15c) (kthread) from (ret_from_fork+0x14/0x24) At first, I thought prev->next was overwritten. Later, I carefully analyzed the RCU code and the disassembly code. The error occurred when deleting a node from the list rcu_state.gp_wq. The System.map shows that the address of rcu_state is c0840c00. Then I use gdb to obtain the offset of rcu_state.gp_wq.task_list. (gdb) p &((struct rcu_state *)0)->gp_wq.task_list $1 = (struct list_head *) 0x4dc Again: list_del corruption. prev->next should be c0ecbf74, but was c08410dc c08410dc = c0840c00 + 0x4dc = &rcu_state.gp_wq.task_list Because rcu_state.gp_wq has at most one node, so I can guess that "prev = &rcu_state.gp_wq.task_list". But for other scenes, maybe I wasn't so lucky, I cannot figure out the value of 'prev'. Link: https://lkml.kernel.org/r/20211207025835.1909-1-thunder.leizhen@huawei.comSigned-off-by:Zhen Lei <thunder.leizhen@huawei.com> Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com> Signed-off-by:
-
Andy Shevchenko authored
Introduce list_is_head() in the similar (*) way as it's done for list_entry_is_head(). Make use of it in the list.h. *) it's done as inliner and not a macro to be aligned with other list_is_*() APIs; while at it, make all three to have the same style. Link: https://lkml.kernel.org/r/20211201141824.81400-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
