The d0i3_mode element is never set to IWL_D0I3_OFF, so it's not
necessary to check it in iwl_mvm_is_d0i3_supported().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There is a potential race condition when entering suspend with d0i3 in
PCIe.  If there is a frame queued just before we suspend, it won't
complete and we will never clear the queue stuck timer.  To solve
this, call TX_PATH_FLUSH to flush all queues (except the command
queue) as part of the d0i3 entry process.  Add a new function that
returns all the flushable queues.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the prph registers dump is in the transport layer,
and each bus needs an additional dump implementation.

Move the prph dump outside transport, and allow a common
implementation for all of the buses.
This is possible because prph base addresses are similar for
all buses.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Expose _no_grab prph i/o functions that allow performing i/o
outside the transport, without requiring grab and release NIC access
for each operation. In addition, rename the functions so they reflect
their non-grabbing behavior.

This can be very useful for consecutive prph i/o operation that occur
outside trans, such as fw dumps.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This was an old workaround for solving latency issues with
certain Miracast adapters like ActionTec. However this isn't
needed anymore and furthermore it hurts throughput in other
use cases.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure.  Remove it.

Fixes: dbb04b0d ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

As part of the bt_notif file add fields that are currently
not represented
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add mplut and sync2sco and corunning to debugfs.
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The d0i3 flag in the device configuration structure is redundant,
because the same information can be determined by checking the
firmware capability flag.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to catch different TDLS events and get the
firmware data when they occur.
Add empty TX_LATENCY trigger on the way to avoid mismatch
with trees in which this trigger is implemented.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware debug trigger ID is always a compile-time constant,
so we can use a build-time assertion to validate that it is in
fact a valid constant.

To make that really guaranteed to work, convert this and the
inline function iwl_fw_dbg_trigger_simple_stop() to macros.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This function updates the pairwise keys as well.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The PCIe transport will also need a d0i3_entry_timeout_ms parameter,
so move the existing one from the slave transports to iwlwifi, so it
can be reused.  While at it, rename the parameter to something
shorter, namely d0i3_entry_delay.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This message isn't very useful and presents a security risk
due to the use of %p - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of using an external NVM file, the driver sends to the
FW the different nvm sections. In the response of the cmd, the
FW states the status of the writing of the chunk.

Currently the value is not checked by the driver.

Check FW's response for writing the nvm chunk in the NVM_ACCESS_CMD.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If the firmware sends LMAC scan notifications while a UMAC scan is
running, just WARN and ignore it, otherwise the scanning state gets
messed up.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When there's a bt-wifi contention that requires arbitration,
we use a priority-based mechanism to decide which comm wins.
Over time, use cases become more and more complex, with multiple
concurrent active links with different traffic types and different QoS
requirements, on both WiFi and BT sides.
This, in turn, requires us to elaborate our prioritization mechanism.
However, our legacy products included hw that does not supports this,
so selectively enable this on specific hw - as signaled by the firmware.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This code was needed during initial PAN bringup, but now is
just cruft - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure the FW to use fragmented scan when the traffic load is high
or low latency traffic is on. This is useful for scans that are
managed by the FW (e.g. scheduled scan).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Make the various conversion functions typesafe, so we don't
accidentally try to call them with the wrong pointers and
cast them to something that will crash.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The split of iwlwifi into DVM and MVM was a long time ago now,
so we can remove the "default IWLWIFI" that we had to keep all
existing .config files with working defaults during the split.
This is no longer necessary, practically nobody should now be
upgrading a .config that's older than the split.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

802.11ac allows A-MSDU that can be up to 12KB long. Since
an entire A-MSDU needs to fit into one single Receive
Buffer (RB), add support for big RBs.
Since this adds lots of pressure to the memory manager and
significantly increase the true_size of the RX buffers,
don't enable this by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This is a workaround to an OTP bug. In Series 8000 1x1, the OTP
0xA052 defines 2x2 antenna configuration. This workaround overrides
the decision based on HW id and on MIMO disabled bit which is
correct in the OTP and set to disabled. This fixes the previous
workaround "force 1x1 antenna in Series 8000".
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

mac80211_hwsim was not placed alphabetically correctly in menuconfig, fix that.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Change menuconfig to config to keep the Kconfig entries unified. Part of
reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Rename WL_TI to WLAN_VENDOR_TI to match with other vendor configs and make sure
that it's enabled by default in new configs. Convert menuconfigs to regular
configs to unify the wireless drivers menuconfig. Part of reorganising wireless
drivers directory and Kconfig.

Also remove WLCORE dependency to WL_TI. It should not be needed as WLCORE is
already under if  WLAN_VENDOR_TI.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add new a Kconfig file and a vendor config for realtek. Also update MAINTAINERS
which we missed to do when earlier moving rtlwifi.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>