... instead of changing mode->clock, which we should leave as-is.

After the previous patch we only touch that if it's a panel, and then
adjusted mode->clock equals adjusted_mode->clock. Outside of
intel_dp.c we only use ajusted_mode->clock in the mode_set functions.

Within intel_dp.c we only use it to calculate the dp dithering
and link bw parameters, so that's the only thing we need to fix
up.

As a temporary ugliness (until the cleanup in the next patch) we
pass the adjusted_mode into dp_dither for both parameters (because
that one still looks at mode->clock).

Note that we do overwrite adjusted_mode->clock with the selected dp
link clock, but that only happens after we've calculated everything we
need based on the dotclock of the adjusted output configuration.

Outside of intel_dp.c only intel_display.c uses adjusted_mode->clock,
and that stays the same after this patch (still equals the selected dp
link clock). intel_display.c also needs the actual dotclock (as
target_clock), but that has been fixed up in the previous patch.

v2: Adjust the debug message to also use adjusted_mode->clock.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

... instead of abusing mode->clock by storing it in there - we
shouldn't touch that one at all. This patch is the first prep step to
constify the mode argument of the intel_dp_mode_fixup function.

The next patch will stop us from modifying mode->clock.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Both busy_ioctl and the new wait_ioct need to do the same dance (or at
least should). Some slight changes:
- busy_ioctl now unconditionally checks for olr. Before emitting a
  require flush would have prevent the olr check and hence required a
  second call to the busy ioctl to really emit the request.
- the timeout wait now also retires request. Not really required for
  abi-reasons, but makes a notch more sense imo.

I've tested this by pimping the i-g-t test some more and also checking
the polling behviour of the wait_rendering_timeout ioctl versus what
busy_ioctl returns.

v2: Too many people complained about unplug, new color is
flush_active.

v3: Kill the comment about the unplug moniker.

v4: s/un-active/inactive/
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Instead of checking for !CPT, check for IBX to make it clearer that
this is a IBX-specific workaround. No functional change because we
smash the PPT PCH into the HAS_PCH_CPT check and atm DP isn't enabled
on the haswell LPT PCH yet.

See Bspec Vol 3, Part 3, Section 4.[3-5].1 about DP[BCD], bit 30 for
details of this workaround.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Positively checking for the required feature/gen is simpler than build
a cascade of negative "we need to bail" checks. And the later won't
scale if we add more stuff that doesn't fit in nicely.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This fixes an (albeit really hard to hit) race resulting in an oops:
- The parity work get scheduled.
- We re-init the irq state and call INIT_WORK again.
- The workqueue code tries to run the work item and stumbles over a
  work item that should be on it's runlist.

Also initiliaze the work item unconditionally like all the others,
it's simpler.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Notice by Fengguang Wu's automatic sparse checker.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This is the same as the nouveau code pretty much.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Tested sharing to udl.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This allows udl to get a vmapping of an imported buffer for scanout.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This is used to export a vmapping to the udl driver so that
i915 and udl can share the udl scanout.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This just adds a stub until we have pieces in place to test
a correct one.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This just adds a stub until we have some users in place to test
this with.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This just adds a stub for now, until we have some users in
place to test this functionality properly.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Dumb binary interfaces which allow root-only updates of the cache
remapping registers. As mentioned in a previous patch, software using
this interface needs to know about HW limits, and other programming
considerations as the kernel interface does no checking for these things
on the root-only interface.

v1: Drop extra posting reads (Chris)
Return negative values in the sysfs interfaces on errors (Chris)

v2: Return -EINVAL for offset % 4 (Jesse)
Move schizo userspace check out (Jesse)
Cleaner sysfs item initializers (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

If any l3 rows have been previously remapped, we must remap them after
GPU reset/resume too.

v2: Just return (no warn) on remapping init if not IVB (Jesse)
Move the check of schizo userspace to i915_gem_l3_remap (Jesse)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The previous patch put all the code, and handlers in place. It should
now be safe to enable the parity error interrupt. The parity error must
be unmasked in both the GTIMR, and the CS IMR. Unfortunately, the docs
aren't clear about this; nevertheless it's the truth.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

On IVB hardware we are given an interrupt whenever a L3 parity error
occurs in the L3 cache. The L3 cache is used by internal GPU clients
only.  This is a very rare occurrence (in fact to test this I need to
use specially instrumented silicon).

When a row in the L3 cache detects a parity error the HW generates an
interrupt. The interrupt is masked in GTIMR until we get a chance to
read some registers and alert userspace via a uevent. With this
information userspace can use a sysfs interface (follow-up patch) to
remap those rows.

Way above my level of understanding, but if a given row fails, it is
statistically more likely to fail again than a row which has not failed.
Therefore it is desirable for an operating system to maintain a lifelong
list of failing rows and always remap any bad rows on driver load.
Hardware limits the number of rows that are remappable per bank/subbank,
and should more than that many rows detect parity errors, software
should maintain a list of the most frequent errors, and remap those
rows.

V2: Drop WARN_ON(IS_GEN6) (Jesse)
DRM_DEBUG row/bank/subbank on errror (Jesse)
Comment updates (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

A 30 ms delay is simply way too big to waste cpu cycles on.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Jesse extracted this nice helper in his i9xx_crtc_mode_set refactor,
but we have the identical code in ironlake_ccrtc_mode_set. And that
function is huge, so extracting some code full of magic numbers is
always nice.

Noticed while trying to get a handle on our dp clock code.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Already discovered in

commit 5a117db7
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date:   Thu Jan 5 09:34:29 2012 -0200

    drm/i915: there is no pipe CxSR on ironlake

but we've failed to rip out the code from the ironlake specific code.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

On IVB and older, we basically have two registers: the control and the
data register. We write a few consecutitve times to the control
register, and we need these writes to arrive exactly in the specified
order.

Also, when we're changing the data register, we need to guarantee that
anything written to the control register already arrived (since
changing the control register can change where the data register
points to). Also, we need to make sure all the writes to the data
register happen exactly in the specified order, and we also *can't*
read the data register during this process, since reading and/or
writing it will change the place it points to.

So invoke the "better safe than sorry" rule and just be careful and
put barriers everywhere :)

On HSW we still have a control register that we write many times, but
we have many data registers.
Demanded-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

HSW support is now just like all the other generations: we send AVI
and SPD InfoFrames. There are other DIPs for HSW, but there are other
DIPs for the previous generations too. For each gen, we can see which
DIPs are missing by looking at the 'set_infoframes' function: we
explicitly disable the DIPs we're not using.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The register that controls the HDMI port can be used to control the
sDVO port. Some bits are defined only for sDVO, and SDVO_BORDER_ENABLE
is one of those: HDMI ports that can't be used in sDVO mode don't even
have this bit defined in their specifications.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

At this time, the HDMI port is enabled, and the DIP control register
specification says we need to disable the port *before* disabling the
DIPs. Also, while doing this we risk telling the HW to send the AVI
DIPs once (not every VSync), which really seems to confuse the HW and
trigger bugs where the DIPs are not sent.

This code was here just to set the DIP register to a 'known state'
before using it, but since now the set_infoframes functions already
set the control registers to a known state, this code can go away.

Also, the previous code disables *all* the DIP registers for *each*
HDMI port, so we end disabling each DIP register more than once.

This patch solves a problem I can reproduce on my IVB machine. When I
boot it with just a single HDMI monitor, the AVI InfoFrames are not
sent. With this patch, the InfoFrames are sent. Previously, I wrote a
patch to 'touch the DIP registers after we enable the HDMI port' to
solve this same problem, but that patch doesn't seem to be needed
anymore after this patch.

All this patch does is revert a chunk of the following commit:

    commit 64a8fc01
    Author: Jesse Barnes <jbarnes@virtuousgeek.org>
    Date:   Thu Sep 22 11:16:00 2011 +0530

        drm/i915: fix ILK+ infoframe support

So bugs that can be bisected to that commit may be fixed now.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43256Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The register specification says we need to do this.

V2: Only write the register if the port is enabled.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

From this point on, the 'set_infoframe' functions always set the DIP
registers to a known state, so anything done will always be undone at
the modeset.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This function is called when the pipe is disabled, so it always gets
the 50ms timeout.

This function is called once for each InfoFrame, so we actually get a
100ms timeout. Will be more if we add more InfoFrames.

Also, the spec says we need to "wait for a VSync to ensure completion
of any pending DIP transmissions", not for a VBlank. OTOH, the
register documentation suggests that the DIPs are sent *during* the
VSync, so shouldn't we be waiting until *after* the VSync to ensure
all DIPs are sent?

So this wait_for_vblank seems, besides useless, totally wrong.

If we ever want to change some specific InfoFrame on-the-fly (outside
of the modeset code), the code that changes the InfoFrame will have to
do the waiting itself, and properly.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

So the write_infoframe function can assume the DIP is on.

V2: Be more defensive and add WARN().
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Not once for each InfoFrame. Now we have a function that allows us to
do this.

[danvet: Paulo clarified on irc that a later bugfix patch needs this
cleanup.]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This solves problems that happen when you alternate between HDMI and
DVI on the same port. I can reproduce these problems using DP->HDMI
and DP->DVI adapters on a DP port.

When you first plug HDMI and then plug DVI, you need to stop sending
DIPs, even if the port is in DVI mode (see the HDMI register spec). If
you don't stop sending DIPs, you'll see a pink vertical line on the
left side of the screen, some modes will give you a black screen, some
modes won't work correctly.

When you first plug DVI and then plug HDMI, you need to properly
enable the DIPs, otherwise the HW won't send them. After spending a
lot of time investigating this, I concluded that if the DIPs are
disabled, we should not write to the DIP register again because when
we do this, we also set the AVI InfoFrame frequency to "once", and
this seems to really confuse our hardware. Since this problem was not
exactly easy to debug, I'm adopting the defensive behavior and not
just avoing the "disable twice" sequence, but also explicitly
selecting the AVI InfoFrame and setting its frequency to a correct
one.

Also, move the "is_dvi" check from intel_set_infoframe to the
set_infoframes functions since now they're going to be the first ones
to deal with the DIP registers.

This patch adds the code to fix the problem, but it depends on the
removal of some code that can't be removed right now and will come
later in the patch series. The patch that we need is:
  - drm/i915: don't write 0 to DIP control at HDMI init

[danvet: Paulo clarified that this additional patch is only required
to make the fix complete, this patch here alone doesn't introduce a
regression but only partially solves the problem of randomly clearing
the dip registers.]

V2: Be even more defensive by selecting AVI and setting its frequency
outside the "is_dvi" check.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We need a function that is able to fully 'set' the state of the DIP
registers to a known state.

Currently, we have the write_infoframe function that is called twice:
once for AVI and once for SPD. The problem is that write_infoframe
tries to keep the state of the DIP register as it is, changing only
the minimum necessary bits. The second problem is that
write_infoframe does twice (once for each time it is called) some
work that should be done only once (like waiting for vblank and
setting the port). If we add even more DIPs, it will do even more
repeated work.

This patch only adds the infrastructure keeping the code behavior the
same as before.

v2: add static keywords
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull ceph updates from Sage Weil:
 "There are some updates and cleanups to the CRUSH placement code, a bug
  fix with incremental maps, several cleanups and fixes from Josh Durgin
  in the RBD block device code, a series of cleanups and bug fixes from
  Alex Elder in the messenger code, and some miscellaneous bounds
  checking and gfp cleanups/fixes."

Fix up trivial conflicts in net/ceph/{messenger.c,osdmap.c} due to the
networking people preferring "unsigned int" over just "unsigned".

* git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (45 commits)
  libceph: fix pg_temp updates
  libceph: avoid unregistering osd request when not registered
  ceph: add auth buf in prepare_write_connect()
  ceph: rename prepare_connect_authorizer()
  ceph: return pointer from prepare_connect_authorizer()
  ceph: use info returned by get_authorizer
  ceph: have get_authorizer methods return pointers
  ceph: ensure auth ops are defined before use
  ceph: messenger: reduce args to create_authorizer
  ceph: define ceph_auth_handshake type
  ceph: messenger: check return from get_authorizer
  ceph: messenger: rework prepare_connect_authorizer()
  ceph: messenger: check prepare_write_connect() result
  ceph: don't set WRITE_PENDING too early
  ceph: drop msgr argument from prepare_write_connect()
  ceph: messenger: send banner in process_connect()
  ceph: messenger: reset connection kvec caller
  libceph: don't reset kvec in prepare_write_banner()
  ceph: ignore preferred_osd field
  ceph: fully initialize new layout
  ...

Pull perf updates from Ingo Molnar.

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
  perf ui browser: Stop using 'self'
  perf annotate browser: Read perf config file for settings
  perf config: Allow '_' in config file variable names
  perf annotate browser: Make feature toggles global
  perf annotate browser: The idx_asm field should be used in asm only view
  perf tools: Convert critical messages to ui__error()
  perf ui: Make --stdio default when TUI is not supported
  tools lib traceevent: Silence compiler warning on 32bit build
  perf record: Fix branch_stack type in perf_record_opts
  perf tools: Reconstruct event with modifiers from perf_event_attr
  perf top: Fix counter name fixup when fallbacking to cpu-clock
  perf tools: fix thread_map__new_by_pid_str() memory leak in error path
  perf tools: Do not use _FORTIFY_SOURCE when DEBUG=1 is specified
  tools lib traceevent: Fix signature of create_arg_item()
  tools lib traceevent: Use proper function parameter type
  tools lib traceevent: Fix freeing arg on process_dynamic_array()
  tools lib traceevent: Fix a possibly wrong memory dereference
  tools lib traceevent: Fix a possible memory leak
  tools lib traceevent: Allow expressions in __print_symbolic() fields
  perf evlist: Explicititely initialize input_name
  ...

Pull i2c updates from Jean Delvare.

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Split I2C_M_NOSTART support out of I2C_FUNC_PROTOCOL_MANGLING
  i2c-dev: Add support for I2C_M_RECV_LEN

Pull second set of watchdog updates from Wim Van Sebroeck:
 "This changeset contains following changes:
   * Add support for multiple watchdog devices.  We use dynamically
     allocated device id's for this.
   * Add locking into the generic watchdog infrastructure.
   * Add support for dynamically allocated watchdog_device structs so
     that we can deal with devices that get unbound.
   * convert following drivers to the generic watchdog framework:
     sch5627, sch5636 and sp805_wdt.
   * Add DA9052/53 PMIC watchdog support
   * Fix printk format warnings for iTCO_wdt.c"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: iTCO_wdt.c: fix printk format warnings
  watchdog: sp805_wdt: Add clk_{un}prepare support
  watchdog: sp805_wdt: convert to watchdog core
  hwmon/sch56xx: Depend on watchdog for watchdog core functions
  watchdog: sch56xx-common: set correct bits in register()
  Watchdog: DA9052/53 PMIC watchdog support
  watchdog: sch56xx-common: Add proper ref-counting of watchdog data
  watchdog: sch56xx: Remove unnecessary checks for register changes
  watchdog: sch56xx: Use watchdog core
  watchdog: Add support for dynamically allocated watchdog_device structs
  watchdog: Add Locking support
  watchdog: watchdog_dev: Rewrite wrapper code
  watchdog: use dev_ functions
  watchdog: create all the proper device files
  watchdog: Add a flag to indicate the watchdog doesn't reboot things
  watchdog: Add multiple device support
  watchdog: watchdog_core.h: make functions extern
  watchdog: correct the name of the watchdog_core inlude file
  watchdog: Add watchdog_active() routine
  watchdog: watchdog_dev: include private header to pickup global symbol prototypes

Pull drm fixes from Dave Airlie:
 "Just regular fixes, bunch from intel, quieting some of the over
  zealous power warnings, and the rest just misc.

  I've got another pull with the remaining dma-buf bits, since the vmap
  bits are in your tree now.  I'll send tomorrow just to space things
  out a bit."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
  drm/edid/quirks: ViewSonic VA2026w
  drm/udl: remove unused variables.
  drm/radeon: fix XFX quirk
  drm: Use stdint types for consistency
  drm: Constify params to format_check() and framebuffer_checks()
  drm/radeon: fix typo in trinity tiling setup
  drm/udl: unlock before returning in udl_gem_mmap()
  radeon: make radeon_cs_update_pages static.
  drm/i915: tune down the noise of the RP irq limit fail
  drm/i915: Remove the error message for unbinding pinned buffers
  drm/i915: Limit page allocations to lowmem (dma32) for i965
  drm/i915: always use RPNSWREQ for turbo change requests
  drm/i915: reject doubleclocked cea modes on dp
  drm/i915: Adding TV Out Missing modes.
  drm/i915: wait for a vblank to pass after tv detect
  drm/i915: no lvds quirk for HP t5740e Thin Client
  drm/i915: enable vdd when switching off the eDP panel
  drm/i915: Fix PCH PLL assertions to not assume CRTC:PLL relationship
  drm/i915: Always update RPS interrupts thresholds along with frequency
  drm/i915: properly handle interlaced bit for sdvo dtd conversion
  ...

Pull block driver updates from Jens Axboe:
 "Here are the driver related changes for 3.5.  It contains:

   - The floppy changes from Jiri.  Jiri is now also marked as the
     maintainer of floppy.c, I shall be publically branding his forehead
     with red hot iron at the next opportune moment.

   - A batch of drbd updates and fixes from the linbit crew, as well as
     fixes from others.

   - Two small fixes for xen-blkfront courtesy of Jan."

* 'for-3.5/drivers' of git://git.kernel.dk/linux-block: (70 commits)
  floppy: take over maintainership
  floppy: remove floppy-specific O_EXCL handling
  floppy: convert to delayed work and single-thread wq
  xen-blkfront: module exit handling adjustments
  xen-blkfront: properly name all devices
  drbd: grammar fix in log message
  drbd: check MODULE for THIS_MODULE
  drbd: Restore the request restart logic
  drbd: introduce a bio_set to allocate housekeeping bios from
  drbd: remove unused define
  drbd: bm_page_async_io: properly initialize page->private
  drbd: use the newly introduced page pool for bitmap IO
  drbd: add page pool to be used for meta data IO
  drbd: allow bitmap to change during writeout from resync_finished
  drbd: fix race between drbdadm invalidate/verify and finishing resync
  drbd: fix resend/resubmit of frozen IO
  drbd: Ensure that data_size is not 0 before using data_size-1 as index
  drbd: Delay/reject other state changes while establishing a connection
  drbd: move put_ldev from __req_mod() to the endio callback
  drbd: fix WRITE_ACKED_BY_PEER_AND_SIS to not set RQ_NET_DONE
  ...

Merge block/IO core bits from Jens Axboe:
 "This is a bit bigger on the core side than usual, but that is purely
  because we decided to hold off on parts of Tejun's submission on 3.4
  to give it a bit more time to simmer.  As a consequence, it's seen a
  long cycle in for-next.

  It contains:

   - Bug fix from Dan, wrong locking type.
   - Relax splice gifting restriction from Eric.
   - A ton of updates from Tejun, primarily for blkcg.  This improves
     the code a lot, making the API nicer and cleaner, and also includes
     fixes for how we handle and tie policies and re-activate on
     switches.  The changes also include generic bug fixes.
   - A simple fix from Vivek, along with a fix for doing proper delayed
     allocation of the blkcg stats."

Fix up annoying conflict just due to different merge resolution in
Documentation/feature-removal-schedule.txt

* 'for-3.5/core' of git://git.kernel.dk/linux-block: (92 commits)
  blkcg: tg_stats_alloc_lock is an irq lock
  vmsplice: relax alignement requirements for SPLICE_F_GIFT
  blkcg: use radix tree to index blkgs from blkcg
  blkcg: fix blkcg->css ref leak in __blkg_lookup_create()
  block: fix elvpriv allocation failure handling
  block: collapse blk_alloc_request() into get_request()
  blkcg: collapse blkcg_policy_ops into blkcg_policy
  blkcg: embed struct blkg_policy_data in policy specific data
  blkcg: mass rename of blkcg API
  blkcg: style cleanups for blk-cgroup.h
  blkcg: remove blkio_group->path[]
  blkcg: blkg_rwstat_read() was missing inline
  blkcg: shoot down blkgs if all policies are deactivated
  blkcg: drop stuff unused after per-queue policy activation update
  blkcg: implement per-queue policy activation
  blkcg: add request_queue->root_blkg
  blkcg: make request_queue bypassing on allocation
  blkcg: make sure blkg_lookup() returns %NULL if @q is bypassing
  blkcg: make blkg_conf_prep() take @pol and return with queue lock held
  blkcg: remove static policy ID enums
  ...