The ieee80211_check_combinations() computes
radar_detect accordingly depending on chanctx
reservation status.

This makes it possible to use the function for
channel_switch validation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.

Such reservations are not finalized until all
assigned interfaces are ready.

This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.

This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).

As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.

As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

After sending a TDLS discovery-request, we expect a reply to arrive on
the AP's channel. We must stay on the channel (no PSM, scan, etc.), since
a TDLS setup-response is a direct packet not buffered by the AP.
Add a new mac80211 driver callback to allow discovery session protection.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Make sure userspace added a TDLS peer station before invoking the
transmission of the first setup frame. This ensures packets to the peer
won't go through the AP path.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Write a mac80211 to the cfg80211 API for requesting a userspace TDLS
operation. Define TDLS specific reason codes that can be used here.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

As the spec mandates, flush data in the AP path before transmitting the
first setup frame. Data packets transmitted during setup are already
dropped in the Tx path.

For the teardown flow, flush all packets in the direct path before
transmitting the teardown frame. Un-authorize the peer sta after teardown
is sent, forcing all subsequent Tx to the peer through the AP.

Make sure to flush the queues when disabling the link to get the
teardown packet out.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
[adjust to Luca's new quuee API and stop only vif queues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There are setup/teardown specific actions to be done that accompany
the sending of a TDLS management packet. Split the main function to
simplify future additions.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Use the value from userspace in order to have a correct teardown packet.
With the current code, a teardown from the responder side fails the TDLS
MIC check because of a bad link identifier IE.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.

Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When setting up a TDLS session, register a delayed work to remove
the peer if setup times out. Prevent concurrent setups to support this
capacity.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For TDLS, the AUTHORIZED flag arrives with all other important station
info (supported rates, HT/VHT caps, ...). Make sure to set the station
state in the low-level driver after transferring this information to
the mac80211 STA entry.
This aligns the STA information during sta_state callbacks with the
non-TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Rename the flags used in the Tx path and add an explanation for the
reasons to drop, send directly or through the AP.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of stopping all the hardware queues during channel switch,
which is especially bad when we have large CSA counts, stop only the
queues that are assigned to the vif that is performing the channel
switch.

Additionally, check for (sdata->csa_block_tx) instead of calling
ieee80211_csa_needs_block_tx(), which can now be removed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In some cases we may want to stop the queues of a single vif (for
instance during a channel-switch).  Add a function that stops all the
queues that are assigned to a vif.  If a queue is assigned to more
than one vif, the corresponding netdev subqueue of the other vif(s)
will also be stopped.  If the HW doesn't set the
IEEE80211_HW_QUEUE_CONTROL flag, then all queues are stopped.

Also add a corresponding function to wake the queues of a vif back.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead.  In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not.  For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There is no need to stop all queues when we want to flush specific
queues, so stop only the queues that will be flushed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Converting time from one format to another seems to give coders a warm
and fuzzy feeling.

Use the proper interfaces.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John W. Linville <linville@tuxdriver.com>
[fix compile error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Using perm_addr is always wrong, it may be reassigned by
anyone using standard netdev APIs. Remove that from the
match function and also use the match function where only
the perm_addr was used now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

do_posix_clock_monotonic_gettime() is a leftover from the initial
posix timer implementation which maps to ktime_get_ts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

vif->csa_active is protected by mutexes only. This
means it is unreliable to depend on it on codeflow
in non-sleepable beacon and CSA code. There was no
guarantee to have vif->csa_active update be
visible before beacons are updated on SMP systems.

Using csa counter offsets which are embedded in
beacon struct (and thus are protected with single
RCU assignment) is much safer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Having csa counters part of beacon and probe_resp
structures makes it easier to get rid of possible
races between setting a beacon and updating
counters on SMP systems by guaranteeing counters
are always consistent against given beacon struct.

While at it relax WARN_ON into WARN_ON_ONCE to
prevent spamming logs and racing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[remove pointless array check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Allow send frames using monitor interface
when DFS chandef and we pass CAC (beaconing
allowed).

This fix problem when old kernel and new backports used,
in such case hostapd create/use also monitor interface.
Before this patch all frames hostapd send using monitor
iface were dropped when AP was configured on DFS channel.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.

To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since WEP is practically dead, there seems very little
point in keeping WEP weak IV accounting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The mesh_plink code is doing some interesting things with the
ignore_plink_timer flag.  It seems the original intent was to
handle this race:

cpu 0                           cpu 1
-----                           -----
                                start timer handler for state X
acquire sta_lock
change state from X to Y
mod_timer() / del_timer()
release sta_lock
                                acquire sta_lock
                                execute state Y timer too soon

However, using the mod_timer()/del_timer() return values to
detect these cases is broken.  As a result, timers get ignored
unnecessarily, and stations can get stuck in the peering state
machine.

Instead, we can detect the case by looking at the timer expiration.
In the case of del_timer, just ignore the timers in the following
(LISTEN/ESTAB) states since they won't have timers anyway.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

It is currently possible to have a race due to the station PS
unblock work like this:
 * station goes to sleep with frames buffered in the driver
 * driver blocks wakeup
 * station wakes up again
 * driver flushes/returns frames, and unblocks, which schedules
   the unblock work
 * unblock work starts to run, and checks that the station is
   awake (i.e. that the WLAN_STA_PS_STA flag isn't set)
 * we process a received frame with PM=1, setting the flag again
 * ieee80211_sta_ps_deliver_wakeup() runs, delivering all frames
   to the driver, and then clearing the WLAN_STA_PS_DRIVER and
   WLAN_STA_PS_STA flags

In this scenario, mac80211 will think that the station is awake,
while it really is asleep, and any TX'ed frames should be filtered
by the device (it will know that the station is sleeping) but then
passed to mac80211 again, which will not buffer it either as it
thinks the station is awake, and eventually the packets will be
dropped.

Fix this by moving the clearing of the flags to exactly where we
learn about the situation. This creates a problem of reordering,
so introduce another flag indicating that delivery is being done,
this new flag also queues frames and is cleared only while the
spinlock is held (which the queuing code also holds) so that any
concurrent delivery/TX is handled correctly.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Minstrel has long since proven its worth.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull networking fixes from David Miller:

 1) Fix checksumming regressions, from Tom Herbert.

 2) Undo unintentional permissions changes for SCTP rto_alpha and
    rto_beta sysfs knobs, from Denial Borkmann.

 3) VXLAN, like other IP tunnels, should advertize it's encapsulation
    size using dev->needed_headroom instead of dev->hard_header_len.
    From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: sctp: fix permissions for rto_alpha and rto_beta knobs
  vxlan: Checksum fixes
  net: add skb_pop_rcv_encapsulation
  udp: call __skb_checksum_complete when doing full checksum
  net: Fix save software checksum complete
  net: Fix GSO constants to match NETIF flags
  udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
  vxlan: use dev->needed_headroom instead of dev->hard_header_len
  MAINTAINERS: update cxgb4 maintainer

Pull more clock framework updates from Mike Turquette:
 "This contains the second half the of the clk changes for 3.16.

  They are simply fixes and code refactoring for the OMAP clock drivers.
  The sunxi clock driver changes include splitting out the one
  mega-driver into several smaller pieces and adding support for the A31
  SoC clocks"

* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
  clk: sunxi: document PRCM clock compatible strings
  clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
  clk: sun6i: Protect SDRAM gating bit
  clk: sun6i: Protect CPU clock
  clk: sunxi: Rework clock protection code
  clk: sunxi: Move the GMAC clock to a file of its own
  clk: sunxi: Move the 24M oscillator to a file of its own
  clk: sunxi: Remove calls to clk_put
  clk: sunxi: document new A31 USB clock compatible
  clk: sunxi: Implement A31 USB clock
  ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
  CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
  ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
  CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
  CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
  dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
  ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
  CLK: TI: gate: add composite interface clock to OMAP2 only build
  ARM: OMAP2: clock: add DT boot support for cpufreq_ck
  CLK: TI: OMAP2: add clock init support
  ...

Pull NVMe update from Matthew Wilcox:
 "Mostly bugfixes again for the NVMe driver.  I'd like to call out the
  exported tracepoint in the block layer; I believe Keith has cleared
  this with Jens.

  We've had a few reports from people who're really pounding on NVMe
  devices at scale, hence the timeout changes (and new module
  parameters), hotplug cpu deadlock, tracepoints, and minor performance
  tweaks"

[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
  end up going away when mq conversion happens ]

* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
  NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
  NVMe: Use Log Page constants in SCSI emulation
  NVMe: Define Log Page constants
  NVMe: Fix hot cpu notification dead lock
  NVMe: Rename io_timeout to nvme_io_timeout
  NVMe: Use last bytes of f/w rev SCSI Inquiry
  NVMe: Adhere to request queue block accounting enable/disable
  NVMe: Fix nvme get/put queue semantics
  NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
  NVMe: Make admin timeout a module parameter
  NVMe: Make iod bio timeout a parameter
  NVMe: Prevent possible NULL pointer dereference
  NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
  NVMe: Update data structures for NVMe 1.2
  NVMe: Enable BUILD_BUG_ON checks
  NVMe: Update namespace and controller identify structures to the 1.1a spec
  NVMe: Flush with data support
  NVMe: Configure support for block flush
  NVMe: Add tracepoints
  NVMe: Protect against badly formatted CQEs
  ...

Commit 3fd091e7 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.

RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:

  [...]
  C3)  When a new RTT measurement R' is made, set

       RTTVAR <- (1 - RTO.Beta) * RTTVAR + RTO.Beta * |SRTT - R'|

       and

       SRTT <- (1 - RTO.Alpha) * SRTT + RTO.Alpha * R'

       Note: The value of SRTT used in the update to RTTVAR
       is its value before updating SRTT itself using the
       second assignment. After the computation, update
       RTO <- SRTT + 4 * RTTVAR.

  C4)  When data is in flight and when allowed by rule C5
       below, a new RTT measurement MUST be made each round
       trip. Furthermore, new RTT measurements SHOULD be
       made no more than once per round trip for a given
       destination transport address. There are two reasons
       for this recommendation: First, it appears that
       measuring more frequently often does not in practice
       yield any significant benefit [ALLMAN99]; second,
       if measurements are made more often, then the values
       of RTO.Alpha and RTO.Beta in rule C3 above should be
       adjusted so that SRTT and RTTVAR still adjust to
       changes at roughly the same rate (in terms of how many
       round trips it takes them to reflect new values) as
       they would if making only one measurement per
       round-trip and using RTO.Alpha and RTO.Beta as given
       in rule C3. However, the exact nature of these
       adjustments remains a research issue.
  [...]

While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.

Fixes: 3fd091e7 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
Fixes related to some recent checksum modifications.

- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
  whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5
("net: Save software checksum complete") is not correct.

This patch:
1) Restores code in __skb_checksum_complete_header except for setting
   CHECKSUM_UNNECESSARY. This function may be calculating checksum on
   something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
   checksum 0..skb->len is calculated without adding in pseudo header.
   This value is saved in skb->csum and then the pseudo header is added
   to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
   set skb->csum_valid to whether checksum of zero was computed. This
   allows skb_csum_unnecessary to return true without changing to
   CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>