If wol state of phy hardware is enabled after reset, phy_ethtool_get_wol()
returns that wol.wolopts is true.

However, since net_device.wol_enabled is zero and this doesn't apply wol
state until calling ethtool_set_wol(), so mdio_bus_phy_may_suspend()
returns true, that is, it's in a state where phy can suspend even though
wol state is enabled.

In this inconsistency, phy_suspend() returns -EBUSY, and at last,
suspend sequence fails with the following message:

    dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x58 returns -16
    PM: Device 65000000.ethernet-ffffffff:01 failed to suspend: error -16
    PM: Some devices failed to suspend, or early wake event detected

In order to fix the above issue, this patch forces to set initial wol state
to disabled as default.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces suspend and resume functions to ave driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-4.21-20181128' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
This is a pull request for net-next/master consisting of 18 patches.

The first patch is by Colin Ian King and fixes the spelling in the ucan
driver.

The next three patches target the xilinx driver. YueHaibing's patch
fixes the return type of ndo_start_xmit function. Two patches by
Shubhrajyoti Datta add support for the CAN FD 2.0 controllers.

Flavio Suligoi's patch for the sja1000 driver add support for the ASEM
CAN raw hardware.

Wolfram Sang's and Kuninori Morimoto's patches switch the rcar driver to
use SPDX license identifiers.

The remaining 111 patches improve the flexcan driver. Pankaj Bansal's
patch enables the driver in Kconfig on all architectures with IOMEM
support. The next four patches by me fix indention, add missing
parentheses and comments. Aisheng Dong's patches add self wake support
and document it in the DT bindings. The remaining patches by Pankaj
Bansal first fix the loopback support and prepare the driver for the
CAN-FD support needed for the LX2160A SoC. The actual CAN-FD support
will be added in a later patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) ARM64 JIT fixes for subprog handling from Daniel Borkmann.

 2) Various sparc64 JIT bug fixes (fused branch convergance, frame
    pointer usage detection logic, PSEODU call argument handling).

 3) Fix to use BH locking in nf_conncount, from Taehee Yoo.

 4) Fix race of TX skb freeing in ipheth driver, from Bernd Eckstein.

 5) Handle return value of TX NAPI completion properly in lan743x
    driver, from Bryan Whitehead.

 6) MAC filter deletion in i40e driver clears wrong state bit, from
    Lihong Yang.

 7) Fix use after free in rionet driver, from Pan Bian.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
  s390/qeth: fix length check in SNMP processing
  net: hisilicon: remove unexpected free_netdev
  rapidio/rionet: do not free skb before reading its length
  i40e: fix kerneldoc for xsk methods
  ixgbe: recognize 1000BaseLX SFP modules as 1Gbps
  i40e: Fix deletion of MAC filters
  igb: fix uninitialized variables
  netfilter: nf_tables: deactivate expressions in rule replecement routine
  lan743x: Enable driver to work with LAN7431
  tipc: fix lockdep warning during node delete
  lan743x: fix return value for lan743x_tx_napi_poll
  net: via: via-velocity: fix spelling mistake "alignement" -> "alignment"
  qed: fix spelling mistake "attnetion" -> "attention"
  net: thunderx: fix NULL pointer dereference in nic_remove
  sctp: increase sk_wmem_alloc when head->truesize is increased
  firestream: fix spelling mistake: "Inititing" -> "Initializing"
  net: phy: add workaround for issue where PHY driver doesn't bind to the device
  usbnet: ipheth: fix potential recvmsg bug and recvmsg bug 2
  sparc: Adjust bpf JIT prologue for PSEUDO calls.
  bpf, doc: add entries of who looks over which jits
  ...

Pull Xtensa fixes from Max Filippov:

 - fix kernel exception on userspace access to a currently disabled
   coprocessor

 - fix coprocessor data saving/restoring in configurations with multiple
   coprocessors

 - fix ptrace access to coprocessor data on configurations with multiple
   coprocessors with high alignment requirements

* tag 'xtensa-20181128' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix coprocessor part of ptrace_{get,set}xregs
  xtensa: fix coprocessor context offset definitions
  xtensa: enable coprocessors that are being flushed

Jeff Kirsher says:

====================
Intel Wired LAN Driver Fixes 2018-11-28

This series contains fixes to igb, ixgbe and i40e.

Yunjian Wang from Huawei resolves a variable that could potentially be
NULL before it is used.

Lihong fixes an i40e issue which goes back to 4.17 kernels, where
deleting any of the MAC filters was causing the incorrect syncing for
the PF.

Josh Elsasser caught that there were missing enum values in the link
capabilities for x550 devices, which was preventing link for 1000BaseLX
SFP modules.

Jan fixes the function header comments for XSK methods.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The response for a SNMP request can consist of multiple parts, which
the cmd callback stages into a kernel buffer until all parts have been
received. If the callback detects that the staging buffer provides
insufficient space, it bails out with error.
This processing is buggy for the first part of the response - while it
initially checks for a length of 'data_len', it later copies an
additional amount of 'offsetof(struct qeth_snmp_cmd, data)' bytes.

Fix the calculation of 'data_len' for the first part of the response.
This also nicely cleans up the memcpy code.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:26:6:
 warning: variable 'ip_family' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:27:6:
 warning: variable 'fc_seq' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:28:6:
 warning: variable 'qos_id' set but not used [-Wunused-but-set-variable]

It never used since introduction in commit
ceed73a2 ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c:4011:5:
 warning: variable 'max_hw_rings' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c:4013:6:
 warning: variable 'cur_rings' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c:2996:25:
 warning: variable 'tx_desc_info' set but not used [-Wunused-but-set-variable]

'cur_rings, max_hw_rings' never used since introduction in commit
34e8c406 ("qlcnic: refactor Tx/SDS ring calculation and validation in driver.")
'tx_desc_info' never used since commit
95b3890a ("qlcnic: Enhance Tx timeout debugging.")
Also 'queue_type' only can be QLCNIC_RX_QUEUE/QLCNIC_TX_QUEUE,
so make a trival cleanup on if statement.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/neterion/vxge/vxge-traffic.c:1698:35:
 warning: variable 'txdl_priv' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/neterion/vxge/vxge-traffic.c:1699:6:
 warning: variable 'max_frags' set but not used [-Wunused-but-set-variable]

It never used since introduction in
commit 11324132 ("Neterion: New driver: Traffic & alarm handler")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Disable BH while holding list spinlock in nf_conncount, from
   Taehee Yoo.

2) List corruption in nf_conncount, also from Taehee.

3) Fix race that results in leaving around an empty list node in
   nf_conncount, from Taehee Yoo.

4) Proper chain handling for inactive chains from the commit path,
   from Florian Westphal. This includes a selftest for this.

5) Do duplicate rule handles when replacing rules, also from Florian.

6) Remove net_exit path in xt_RATEEST that results in splat, from Taehee.

7) Possible use-after-free in nft_compat when releasing extensions.
   From Florian.

8) Memory leak in xt_hashlimit, from Taehee.

9) Call ip_vs_dst_notifier after ipv6_dev_notf, from Xin Long.

10) Fix cttimeout with udplite and gre, from Florian.

11) Preserve oif for IPv6 link-local generated traffic from mangle
    table, from Alin Nastac.

12) Missing error handling in masquerade notifiers, from Taehee Yoo.

13) Use mutex to protect registration/unregistration of masquerade
    extensions in order to prevent a race, from Taehee.

14) Incorrect condition check in tree_nodes_free(), also from Taehee.

15) Fix chain counter leak in rule replacement path, from Taehee.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciocoi Radulescu says:

====================
dpaa2-eth: Introduce XDP support

Add support for XDP programs. Only XDP_PASS, XDP_DROP and XDP_TX
actions are supported for now. Frame header changes are also
allowed.

v2: - count the XDP packets in the rx/tx inteface stats
    - add message with the maximum supported MTU value for XDP
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add counters for xdp processed frames to the channel statistics.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unused counter. Reorder fields in channel stats structure
to match the ethtool strings order and make it easier to print them
with ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send frames back on the same port for XDP_TX action.
Since the frame buffers have been allocated by us, we can recycle
them directly into the Rx buffer pool instead of requesting a
confirmation frame upon transmission complete.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support enqueueing Rx FDs back to hardware, we need to
DMA map Rx buffers as bidirectional.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of freeing the RX buffers, release them back into the pool.
We wait for the maximum number of buffers supported by a single
release command to accumulate before issuing the command.

Also, don't unmap the Rx buffers at the beginning of the Rx routine
anymore, since that would require remapping them before release.
Instead, just do a DMA sync at first and only unmap if the frame is
meant for the stack.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We'll use function free_bufs() on the XDP path as well, so move
it higher in order to avoid a forward declaration.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reserve XDP_PACKET_HEADROOM bytes in Rx buffers to allow XDP
programs to increase frame header size.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We keep one XDP program reference per channel. The only actions
supported for now are XDP_DROP and XDP_PASS.

Until now we didn't enforce a maximum size for Rx frames based
on MTU value. Change that, since for XDP mode we must ensure no
scatter-gather frames can be received.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The net device ndev is freed via free_netdev when failing to register
the device. The control flow then jumps to the error handling code
block. ndev is used and freed again. Resulting in a use-after-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb is freed via dev_kfree_skb_any, however, skb->len is read then. This
may result in a use-after-free bug.

Fixes: e6161d64 ("rapidio/rionet: rework driver initialization and removal")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One method, xsk_umem_setup, had an incorrect kernel doc
description, which has been corrected.

Also fixes small typos found in the comments.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull btrfs fixes from David Sterba:
 "Some of these bugs are being hit during testing so we'd like to get
  them merged, otherwise there are usual stability fixes for stable
  trees"

* tag 'for-4.20-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: relocation: set trans to be NULL after ending transaction
  Btrfs: fix race between enabling quotas and subvolume creation
  Btrfs: send, fix infinite loop due to directory rename dependencies
  Btrfs: ensure path name is null terminated at btrfs_control_ioctl
  Btrfs: fix rare chances for data loss when doing a fast fsync
  btrfs: Always try all copies when reading extent buffers

Pull spi fixes from Mark Brown:
 "A few driver specific fixes here, nothing big or that stands out for
  anyone other than the driver users.

  The omap2-mcspi fix is for issues that started showing up with a
  change in defconfig in this release to make cpuidle get turned on by
  default"

* tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: omap2-mcspi: Add missing suspend and resume calls
  spi: mediatek: use correct mata->xfer_len when in fifo transfer
  spi: uniphier: fix incorrect property items

Add the two 1000BaseLX enum values to the X550's check for 1Gbps modules,
allowing the core driver code to establish a link over this SFP type.

This is done by the out-of-tree driver but the fix wasn't in mainline.

Fixes: e23f3336 ("ixgbe: Fix 1G and 10G link stability for X550EM_x SFP+”)
Fixes: 6a14ee0c ("ixgbe: Add X550 support function pointers")
Signed-off-by: Josh Elsasser <jelsasser@appneta.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull kvm fixes from Paolo Bonzini:
 "Bugfixes, many of them reported by syzkaller and mostly predating the
  merge window"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: svm: Ensure an IBPB on all affected CPUs when freeing a vmcb
  kvm: mmu: Fix race in emulated page table writes
  KVM: nVMX: vmcs12 revision_id is always VMCS12_REVISION even when copied from eVMCS
  KVM: nVMX: Verify eVMCS revision id match supported eVMCS version on eVMCS VMPTRLD
  KVM: nVMX/nSVM: Fix bug which sets vcpu->arch.tsc_offset to L1 tsc_offset
  x86/kvm/vmx: fix old-style function declaration
  KVM: x86: fix empty-body warnings
  KVM: VMX: Update shared MSRs to be saved/restored on MSR_EFER.LMA changes
  KVM: x86: Fix kernel info-leak in KVM_HC_CLOCK_PAIRING hypercall
  KVM: nVMX: Fix kernel info-leak when enabling KVM_CAP_HYPERV_ENLIGHTENED_VMCS more than once
  svm: Add mutex_lock to protect apic_access_page_done on AMD systems
  KVM: X86: Fix scan ioapic use-before-initialization
  KVM: LAPIC: Fix pv ipis use-before-initialization
  KVM: VMX: re-add ple_gap module parameter
  KVM: PPC: Book3S HV: Fix handling for interrupted H_ENTER_NESTED

In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.

CC: stable <stable@vger.kernel.org>
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the variable 'phy_word' may be used uninitialized.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The message buffer RAM area is not a contiguous 1KB area but 2 partitions
of 512 bytes each. Till now, we used Message buffers with payload size 8
bytes, which translates to 32 MBs per partition and no spare space is left
in any partition.
However, in upcoming SOC LX2160A the message buffers can have payload size
64 bytes. This results in less than 32 MBs per partition and some empty
area is left at the end of each partition.This empty area should not be
accessed.
Therefore, split the Message Buffer RAM area into two partitions.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Till now the flexcan module supported 8 byte payload size as per CAN 2.0
specifications. But now upcoming flexcan module in NXP LX2160A SOC
supports CAN FD protocol too. The Message buffers need to be configured
to have payload size 64 bytes.

Therefore, added provision in the driver for payload size to be 64 bytes.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

rx offload depends on number of message buffers, which in turn depends
on messgae buffer size. with the upcoming LX2160A SOC the message buffer
size can be configured to 72 bytes if it were to be used in CAN FD mode.

The current mode in which the flexcan is being operated is known at the
time of flexcan_open() but not at the time of flexcan_probe().

Therefore, move the rx_offload_add() from flexcan_probe() to
flexcan_open(). correspondingly, move rx_offload_delete() from
flexcan_remove() to flexcan_close().
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Self reception disable bit needs to be cleared for loopback mode to work
in flexcan.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If wakeup is enabled, enter stop mode, else enter disabled mode. Self wake
can only work on stop mode.

Starting from IMX6, the flexcan stop mode control bits is SoC specific,
move it out of IP driver and parse it from devicetree.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The FlexCAN controller can parse the stop mode property to enable CAN
self wakeup feature.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

With the conversion of the flexcan driver to support both timestamp and
FIFO mode the setup of the MCR register ("enable fifo") has been moved.

This patch moves the comment too, in order to match the code again.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the following checkpatch warning:

| Macro argument 'x' may be better as '(x)' to avoid precedence issues

Fixes: cbffaf7a ("can: flexcan: Always use last mailbox for TX")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The patch fixes the indention by replacing space by tabs, as noted by
checkpatch:

| ERROR: code indent should use tabs where possible
| #980: FILE: drivers/net/can/flexcan.c:980:

Fixes: da49a807 ("can: flexcan: implement error passive state quirk")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the indentio nin flexcan_start_xmit() by alligning the
code to the opening parenthesis.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>