- 01 Jun, 2016 40 commits
-
-
Mathias Nyman authored
commit cdc77c82 upstream. The current implemenentation restart the sent pattern for each entry in the sg list. The receiving end expects a continuous pattern, and test will fail unless scatterilst entries happen to be aligned with the pattern Fix this by calculating the pattern byte based on total sent size instead of just the current sg entry. Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: 8b524901 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing") Acked-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michal Nazarewicz authored
commit f78bbcae upstream. When binding the function to usb_configuration, check whether the thread is running before starting another one. Without that, when function instance is added to multiple configurations, fsg_bing starts multiple threads with all but the latest one being forgotten by the driver. This leads to obvious thread leaks, possible lockups when trying to halt the machine and possible more issues. This fixes issues with legacy/multi¹ gadget as well as configfs gadgets when mass_storage function is added to multiple configurations. This change also simplifies API since the legacy gadgets no longer need to worry about starting the thread by themselves (which was where bug in legacy/multi was in the first place). N.B., this patch doesn’t address adding single mass_storage function instance to a single configuration twice. Thankfully, there’s no legitimate reason for such setup plus, if I’m not mistaken, configfs gadget doesn’t even allow it to be expressed. ¹ I have no example failure though. Conclusion that legacy/multi has a bug is based purely on me reading the code. Acked-by:
Michal Nazarewicz <mina86@mina86.com> Tested-by:
Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Lars-Peter Clausen authored
commit 332a5b44 upstream. In the current implementation functionfs generates a EFAULT for async read operations if the read buffer size is larger than the URB data size. Since a application does not necessarily know how much data the host side is going to send it typically supplies a buffer larger than the actual data, which will then result in a EFAULT error. This behaviour was introduced while refactoring the code to use iov_iter interface in commit c993c39b ("gadget/function/f_fs.c: use put iov_iter into io_data"). The original code took the minimum over the URB size and the user buffer size and then attempted to copy that many bytes using copy_to_user(). If copy_to_user() could not copy all data a EFAULT error was generated. Restore the original behaviour by only generating a EFAULT error when the number of bytes copied is not the size of the URB and the target buffer has not been fully filled. Commit 342f39a6 ("usb: gadget: f_fs: fix check in read operation") already fixed the same problem for the synchronous read path. Fixes: c993c39b ("gadget/function/f_fs.c: use put iov_iter into io_data") Acked-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Lei Liu authored
commit 74d2a91a upstream. Add even more ZTE device ids. Signed-off-by:
lei liu <liu.lei78@zte.com.cn> [johan: rebase and replace commit message ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
lei liu authored
commit f0d09463 upstream. More ZTE device ids. Signed-off-by:
-
Schemmel Hans-Christoph authored
commit 444f94e9 upstream. Added support for Gemalto's Cinterion PH8 and AHxx products with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface. In addition some minor renaming and formatting. Signed-off-by:
Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> [johan: sort current entries and trim trailing whitespace ] Signed-off-by:
-
Johan Hovold authored
commit c8d62957 upstream. URBs and buffers allocated in attach for Epic devices would never be deallocated in case of a later probe error (e.g. failure to allocate minor numbers) as disconnect is then never called. Fix by moving deallocation to release and making sure that the URBs are first unlinked. Fixes: f9c99bb8 ("USB: usb-serial: replace shutdown with disconnect, release") Signed-off-by:
-
Johan Hovold authored
commit c5c0c555 upstream. Private data, URBs and buffers allocated for Epic devices during attach were never released on errors (e.g. missing endpoints). Fixes: 6e8cf775 ("USB: add EPIC support to the io_edgeport driver") Signed-off-by:
-
Johan Hovold authored
commit 028c49f5 upstream. The interface read URB is submitted in attach, but was only unlinked by the driver at disconnect. In case of a late probe error (e.g. due to failed minor allocation), disconnect is never called and we would end up with active URBs for an unbound interface. This in turn could lead to deallocated memory being dereferenced in the completion callback. Fixes: f7a33e60 ("USB: serial: add quatech2 usb to serial driver") Signed-off-by:
-
Johan Hovold authored
commit 35be1a71 upstream. The interface instat and indat URBs were submitted in attach, but never unlinked in release before deallocating the corresponding transfer buffers. In the case of a late probe error (e.g. due to failed minor allocation), disconnect would not have been called before release, causing the buffers to be freed while the URBs are still in use. We'd also end up with active URBs for an unbound interface. Fixes: f9c99bb8 ("USB: usb-serial: replace shutdown with disconnect, release") Signed-off-by:
-
Johan Hovold authored
commit 9e452849 upstream. The interface read and event URBs are submitted in attach, but were never explicitly unlinked by the driver. Instead the URBs would have been killed by usb-serial core on disconnect. In case of a late probe error (e.g. due to failed minor allocation), disconnect is never called and we could end up with active URBs for an unbound interface. This in turn could lead to deallocated memory being dereferenced in the completion callbacks. Fixes: ee467a1f ("USB: serial: add Moxa UPORT 12XX/14XX/16XX driver") Signed-off-by:
-
Konstantin Shkolnyy authored
commit a377f9e9 upstream. A bug in the CRTSCTS handling caused RTS to alternate between CRTSCTS=0 => "RTS is transmit active signal" and CRTSCTS=1 => "RTS is used for receive flow control" instead of CRTSCTS=0 => "RTS is statically active" and CRTSCTS=1 => "RTS is used for receive flow control" This only happened after first having enabled CRTSCTS. Signed-off-by:
Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Fixes: 39a66b8d ("[PATCH] USB: CP2101 Add support for flow control") [johan: reword commit message ] Signed-off-by:
-
Alexander Usyskin authored
commit bc46b45a upstream. Ensure that mei_cl_read_start is called under the device lock also in the bus layer. The function updates global ctrl_wr_list which should be locked. Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
Alexander Usyskin authored
commit 9d04ee11 upstream. When a message is received and amthif client is not in reading state the message is ignored and left dangling in the queue. This may happen after one of the amthif host connections is closed w/o completing the reading. Another client will pick up a wrong message on next read attempt which will lead to link reset. To prevent this the driver has to properly discard the message when amthif client is not in reading state. Signed-off-by:
-
Alexander Usyskin authored
commit 6a8d648c upstream. In the case when disconnection is initiated from the FW the driver is flushing items from the write control list while iterating over it: mei_irq_write_handler() list_for_each_entry_safe(ctrl_wr_list) <-- outer loop mei_cl_irq_disconnect_rsp() mei_cl_set_disconnected() mei_io_list_flush(ctrl_wr_list) <-- destorying list We move the list flushing to the completion routine. Signed-off-by:
-
Takashi Iwai authored
commit c7c999cb upstream. hci_vhci driver creates a hci device object dynamically upon each HCI_VENDOR_PKT write. Although it checks the already created object and returns an error, it's still racy and may build multiple hci_dev objects concurrently when parallel writes are performed, as the device tracks only a single hci_dev object. This patch introduces a mutex to protect against the concurrent device creations. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Jiri Slaby authored
commit 13407376 upstream. The write handler allocates skbs and queues them into data->readq. Read side should read them, if there is any. If there is none, skbs should be dropped by hdev->flush. But this happens only if the device is HCI_UP, i.e. hdev->power_on work was triggered already. When it was not, skbs stay allocated in the queue when /dev/vhci is closed. So purge the queue in ->release. Program to reproduce: #include <err.h> #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/stat.h> #include <sys/types.h> #include <sys/uio.h> int main() { char buf[] = { 0xff, 0 }; struct iovec iov = { .iov_base = buf, .iov_len = sizeof(buf), }; int fd; while (1) { fd = open("/dev/vhci", O_RDWR); if (fd < 0) err(1, "open"); usleep(50); if (writev(fd, &iov, 1) < 0) err(1, "writev"); usleep(50); close(fd); } return 0; } Result: kmemleak: 4609 new suspected memory leaks unreferenced object 0xffff88059f4d5440 (size 232): comm "vhci", pid 1084, jiffies 4294912542 (age 37569.296s) hex dump (first 32 bytes): 20 f0 23 87 05 88 ff ff 20 f0 23 87 05 88 ff ff .#..... .#..... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: ... [<ffffffff81ece010>] __alloc_skb+0x0/0x5a0 [<ffffffffa021886c>] vhci_create_device+0x5c/0x580 [hci_vhci] [<ffffffffa0219436>] vhci_write+0x306/0x4c8 [hci_vhci] Fixes: 23424c0d (Bluetooth: Add support creating virtual AMP controllers) Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Jiri Slaby authored
commit 373a32c8 upstream. Both vhci_get_user and vhci_release race with open_timeout work. They both contain cancel_delayed_work_sync, but do not test whether the work actually created hdev or not. Since the work can be in progress and _sync will wait for finishing it, we can have data->hdev allocated when cancel_delayed_work_sync returns. But the call sites do 'if (data->hdev)' *before* cancel_delayed_work_sync. As a result: * vhci_get_user allocates a second hdev and puts it into data->hdev. The former is leaked. * vhci_release does not release data->hdev properly as it thinks there is none. Fix both cases by moving the actual test *after* the call to cancel_delayed_work_sync. This can be hit by this program: #include <err.h> #include <fcntl.h> #include <stdio.h> #include <stdlib.h> #include <time.h> #include <unistd.h> #include <sys/stat.h> #include <sys/types.h> int main(int argc, char **argv) { int fd; srand(time(NULL)); while (1) { const int delta = (rand() % 200 - 100) * 100; fd = open("/dev/vhci", O_RDWR); if (fd < 0) err(1, "open"); usleep(1000000 + delta); close(fd); } return 0; } And the result is: BUG: KASAN: use-after-free in skb_queue_tail+0x13e/0x150 at addr ffff88006b0c1228 Read of size 8 by task kworker/u13:1/32068 ============================================================================= BUG kmalloc-192 (Tainted: G E ): kasan: bad access detected ----------------------------------------------------------------------------- Disabling lock debugging due to kernel taint INFO: Allocated in vhci_open+0x50/0x330 [hci_vhci] age=260 cpu=3 pid=32040 ... kmem_cache_alloc_trace+0x150/0x190 vhci_open+0x50/0x330 [hci_vhci] misc_open+0x35b/0x4e0 chrdev_open+0x23b/0x510 ... INFO: Freed in vhci_release+0xa4/0xd0 [hci_vhci] age=9 cpu=2 pid=32040 ... __slab_free+0x204/0x310 vhci_release+0xa4/0xd0 [hci_vhci] ... INFO: Slab 0xffffea0001ac3000 objects=16 used=13 fp=0xffff88006b0c1e00 flags=0x5fffff80004080 INFO: Object 0xffff88006b0c1200 @offset=4608 fp=0xffff88006b0c0600 Bytes b4 ffff88006b0c11f0: 09 df 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff88006b0c1200: 00 06 0c 6b 00 88 ff ff 00 00 00 00 00 00 00 00 ...k............ Object ffff88006b0c1210: 10 12 0c 6b 00 88 ff ff 10 12 0c 6b 00 88 ff ff ...k.......k.... Object ffff88006b0c1220: c0 46 c2 6b 00 88 ff ff c0 46 c2 6b 00 88 ff ff .F.k.....F.k.... Object ffff88006b0c1230: 01 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 ................ Object ffff88006b0c1240: 40 12 0c 6b 00 88 ff ff 40 12 0c 6b 00 88 ff ff @..k....@..k.... Object ffff88006b0c1250: 50 0d 6e a0 ff ff ff ff 00 02 00 00 00 00 ad de P.n............. Object ffff88006b0c1260: 00 00 00 00 00 00 00 00 ab 62 02 00 01 00 00 00 .........b...... Object ffff88006b0c1270: 90 b9 19 81 ff ff ff ff 38 12 0c 6b 00 88 ff ff ........8..k.... Object ffff88006b0c1280: 03 00 20 00 ff ff ff ff ff ff ff ff 00 00 00 00 .. ............. Object ffff88006b0c1290: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ Object ffff88006b0c12a0: 00 00 00 00 00 00 00 00 00 80 cd 3d 00 88 ff ff ...........=.... Object ffff88006b0c12b0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 . .............. Redzone ffff88006b0c12c0: bb bb bb bb bb bb bb bb ........ Padding ffff88006b0c13f8: 00 00 00 00 00 00 00 00 ........ CPU: 3 PID: 32068 Comm: kworker/u13:1 Tainted: G B E 4.4.6-0-default #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20151112_172657-sheep25 04/01/2014 Workqueue: hci0 hci_cmd_work [bluetooth] 00000000ffffffff ffffffff81926cfa ffff88006be37c68 ffff88006bc27180 ffff88006b0c1200 ffff88006b0c1234 ffffffff81577993 ffffffff82489320 ffff88006bc24240 0000000000000046 ffff88006a100000 000000026e51eb80 Call Trace: ... [<ffffffff81ec8ebe>] ? skb_queue_tail+0x13e/0x150 [<ffffffffa06e027c>] ? vhci_send_frame+0xac/0x100 [hci_vhci] [<ffffffffa0c61268>] ? hci_send_frame+0x188/0x320 [bluetooth] [<ffffffffa0c61515>] ? hci_cmd_work+0x115/0x310 [bluetooth] [<ffffffff811a1375>] ? process_one_work+0x815/0x1340 [<ffffffff811a1f85>] ? worker_thread+0xe5/0x11f0 [<ffffffff811a1ea0>] ? process_one_work+0x1340/0x1340 [<ffffffff811b3c68>] ? kthread+0x1c8/0x230 ... Memory state around the buggy address: ffff88006b0c1100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88006b0c1180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff88006b0c1200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88006b0c1280: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff88006b0c1300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc Fixes: 23424c0d (Bluetooth: Add support creating virtual AMP controllers) Signed-off-by:
-
Adrian Hunter authored
commit 82296936 upstream. The CMD19/CMD14 bus width test has been found to be unreliable in some cases. It is not essential, so simply remove it. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Matt Gumbel authored
commit 32ecd320 upstream. 008GE0 Toshiba mmc in some Intel Baytrail tablets responds to MMC_SEND_EXT_CSD in 450-600ms. This patch will... () Increase the long read time quirk timeout from 300ms to 600ms. Original author of that quirk says 300ms was only a guess and that the number may need to be raised in the future. () Add this specific MMC to the quirk Signed-off-by:
Matt Gumbel <matthew.k.gumbel@intel.com> Signed-off-by:
-
Gabriele Mazzotta authored
commit ff865123 upstream. Some BIOSes unconditionally send an ACPI notification to RBTN when the system is resuming from suspend. This makes dell-rbtn send an input event to userspace as if a function key was pressed. Prevent this by ignoring all the notifications received while the device is suspended. Link: https://bugzilla.kernel.org/show_bug.cgi?id=106031Signed-off-by:
Gabriele Mazzotta <gabriele.mzt@gmail.com> Tested-by:
Alex Hung <alex.hung@canonical.com> Reviewed-by:
Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Lv Zheng authored
commit 30c9bb0d upstream. The order of the _OSI related functionalities is as follows: acpi_blacklisted() acpi_dmi_osi_linux() acpi_osi_setup() acpi_osi_setup() acpi_update_interfaces() if "!*" <<<<<<<<<<<<<<<<<<<<<<<< parse_args() __setup("acpi_osi=") acpi_osi_setup_linux() acpi_update_interfaces() if "!*" <<<<<<<<<<<<<<<<<<<<<<<< acpi_early_init() acpi_initialize_subsystem() acpi_ut_initialize_interfaces() ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ acpi_bus_init() acpi_os_initialize1() acpi_install_interface_handler(acpi_osi_handler) acpi_osi_setup_late() acpi_update_interfaces() for "!" >>>>>>>>>>>>>>>>>>>>>>>> acpi_osi_handler() Since acpi_osi_setup_linux() can override acpi_dmi_osi_linux(), the command line setting can override the DMI detection. That's why acpi_blacklisted() is put before __setup("acpi_osi="). Then we can notice the following wrong invocation order. There are acpi_update_interfaces() (marked by <<<<) calls invoked before acpi_ut_initialize_interfaces() (marked by ^^^^). This makes it impossible to use acpi_osi=!* correctly from OSI DMI table or from the command line. The use of acpi_osi=!* is meant to disable both ACPICA (acpi_gbl_supported_interfaces) and Linux specific strings (osi_setup_entries) while the ACPICA part should have stopped working because of the order issue. This patch fixes this issue by moving acpi_update_interfaces() to where it is invoked for acpi_osi=! (marked by >>>>) as this is ensured to be invoked after acpi_ut_initialize_interfaces() (marked by ^^^^). Linux specific strings are still handled in the original place in order to make the following command line working: acpi_osi=!* acpi_osi="Module Device". Note that since acpi_osi=!* is meant to further disable linux specific string comparing to the acpi_osi=!, there is no such use case in our bug fixing work and hence there is no one using acpi_osi=!* either from the command line or from the DMI quirks, this issue is just a theoretical issue. Fixes: 741d8128 (ACPI: Add facility to remove all _OSI strings) Tested-by:
Lukas Wunner <lukas@wunner.de> Tested-by:
Chen Yu <yu.c.chen@intel.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Adrian Hunter authored
commit 265984b3 upstream. The CMD19/CMD14 bus width test has been found to be unreliable in some cases. It is not essential, so simply remove it. Signed-off-by:
-
Adrian Hunter authored
commit e5bbf307 upstream. Some devices connected to the SDHCI controller may have separate enabling lines that are controlled through GPIO. These devices need to be powered on and enabled before probing. This is to ensure all devices connected can be seen by the controller. Note, for "stable" this patch depends on the following change: commit 78a898d0 ("ACPI / PM: Export acpi_device_fix_up_power()") Signed-off-by:
Laszlo Fiat <laszlo.fiat@gmail.com> Signed-off-by:
-
Ulf Hansson authored
commit 78a898d0 upstream. Drivers that needs acpi_device_fix_up_power(), allow them to be built as modules by exporting this function. Tested-by:
-
Adrian Hunter authored
commit 1c447116 upstream. Some eMMCs set the partition switch timeout too low. Now typically eMMCs are considered a critical component (e.g. because they store the root file system) and consequently are expected to be reliable. Thus we can neglect the use case where eMMCs can't switch reliably and we might want a lower timeout to facilitate speedy recovery. Although we could employ a quirk for the cards that are affected (if we could identify them all), as described above, there is little benefit to having a low timeout, so instead simply set a minimum timeout. The minimum is set to 300ms somewhat arbitrarily - the examples that have been seen had a timeout of 10ms but were sometimes taking 60-70ms. Signed-off-by:
-
Oliver Hartkopp authored
commit bb208f14 upstream. As described in 'can: m_can: tag current CAN FD controllers as non-ISO' (6cfda7fb) it is possible to define fixed configuration options by setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'. This leads to the incovenience that the fixed configuration bits can not be passed by netlink even when they have the correct values (e.g. non-ISO, FD). This patch fixes that issue and not only allows fixed set bit values to be set again but now requires(!) to provide these fixed values at configuration time. A valid CAN FD configuration consists of a nominal/arbitration bittiming, a data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now enforced by a new can_validate() function. This fix additionally removed the inconsistency that was prohibiting the support of 'CANFD-only' controller drivers, like the RCar CAN FD. For this reason a new helper can_set_static_ctrlmode() has been introduced to provide a proper interface to handle static enabled CAN controller options. Reported-by:
Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Reviewed-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Christophe Ricard authored
commit b58afe6d upstream. Fix static checker warning: drivers/nfc/st21nfca/i2c.c:530 st21nfca_hci_i2c_acpi_request_resources() error: 'gpiod_ena' dereferencing possible ERR_PTR() Fix so that if no enable gpio can be retrieved an -ENODEV is returned. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Fixes: dfa8070d ("nfc: st21nfca: Add support for acpi probing for i2c device.") Signed-off-by:
Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Marc Zyngier authored
commit 7c9b9730 upstream. The GICv3 driver wrongly assumes that it runs on the non-secure side of a secure-enabled system, while it could be on a system with a single security state, or a GICv3 with GICD_CTLR.DS set. Either way, it is important to configure this properly, or interrupts will simply not be delivered on this HW. Reported-by:
Peter Maydell <peter.maydell@linaro.org> Tested-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Will Deacon authored
commit f86c4fbd upstream. When an IPI is generated by a CPU, the pattern looks roughly like: <write shared data> smp_wmb(); <write to GIC to signal SGI> On the receiving CPU we rely on the fact that, once we've taken the interrupt, then the freshly written shared data must be visible to us. Put another way, the CPU isn't going to speculate taking an interrupt. Unfortunately, this assumption turns out to be broken. Consider that CPUx wants to send an IPI to CPUy, which will cause CPUy to read some shared_data. Before CPUx has done anything, a random peripheral raises an IRQ to the GIC and the IRQ line on CPUy is raised. CPUy then takes the IRQ and starts executing the entry code, heading towards gic_handle_irq. Furthermore, let's assume that a bunch of the previous interrupts handled by CPUy were SGIs, so the branch predictor kicks in and speculates that irqnr will be <16 and we're likely to head into handle_IPI. The prefetcher then grabs a speculative copy of shared_data which contains a stale value. Meanwhile, CPUx gets round to updating shared_data and asking the GIC to send an SGI to CPUy. Internally, the GIC decides that the SGI is more important than the peripheral interrupt (which hasn't yet been ACKed) but doesn't need to do anything to CPUy, because the IRQ line is already raised. CPUy then reads the ACK register on the GIC, sees the SGI value which confirms the branch prediction and we end up with a stale shared_data value. This patch fixes the problem by adding an smp_rmb() to the IPI entry code in gic_handle_irq. As it turns out, the combination of a control dependency and an ISB instruction from the EOI in the GICv3 driver is enough to provide the ordering we need, so we add a comment there justifying the absence of an explicit smp_rmb(). Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Manfred Schlaegl authored
commit f49cf3b8 upstream. Pwm config may sleep so defer it using a worker. On a Freescale i.MX53 based board we ran into "BUG: scheduling while atomic" because input_inject_event locks interrupts, but imx_pwm_config_v2 sleeps. Tested on Freescale i.MX53 SoC with 4.6.0. Signed-off-by:
Manfred Schlaegl <manfred.schlaegl@gmx.at> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Roger Quadros authored
commit b49b927f upstream. We shouldn't be calling clk_prepare_enable()/clk_prepare_disable() in an atomic context. Fixes the following issue: [ 5.830970] ehci-omap: OMAP-EHCI Host Controller driver [ 5.830974] driver_register 'ehci-omap' [ 5.895849] driver_register 'wl1271_sdio' [ 5.896870] BUG: scheduling while atomic: udevd/994/0x00000002 [ 5.896876] 4 locks held by udevd/994: [ 5.896904] #0: (&dev->mutex){......}, at: [<c049597c>] __driver_attach+0x60/0xac [ 5.896923] #1: (&dev->mutex){......}, at: [<c049598c>] __driver_attach+0x70/0xac [ 5.896946] #2: (tll_lock){+.+...}, at: [<c04c2630>] omap_tll_enable+0x2c/0xd0 [ 5.896966] #3: (prepare_lock){+.+...}, at: [<c05ce9c8>] clk_prepare_lock+0x48/0xe0 [ 5.897042] Modules linked in: wlcore_sdio(+) ehci_omap(+) dwc3_omap snd_soc_ts3a225e leds_is31fl319x bq27xxx_battery_i2c tsc2007 bq27xxx_battery bq2429x_charger ina2xx tca8418_keypad as5013 leds_tca6507 twl6040_vibra gpio_twl6040 bmp085_i2c(+) palmas_gpadc usb3503 palmas_pwrbutton bmg160_i2c(+) bmp085 bma150(+) bmg160_core bmp280 input_polldev snd_soc_omap_mcbsp snd_soc_omap_mcpdm snd_soc_omap snd_pcm_dmaengine [ 5.897048] Preemption disabled at:[< (null)>] (null) [ 5.897051] [ 5.897059] CPU: 0 PID: 994 Comm: udevd Not tainted 4.6.0-rc5-letux+ #233 [ 5.897062] Hardware name: Generic OMAP5 (Flattened Device Tree) [ 5.897076] [<c010e714>] (unwind_backtrace) from [<c010af34>] (show_stack+0x10/0x14) [ 5.897087] [<c010af34>] (show_stack) from [<c040aa7c>] (dump_stack+0x88/0xc0) [ 5.897099] [<c040aa7c>] (dump_stack) from [<c020c558>] (__schedule_bug+0xac/0xd0) [ 5.897111] [<c020c558>] (__schedule_bug) from [<c06f3d44>] (__schedule+0x88/0x7e4) [ 5.897120] [<c06f3d44>] (__schedule) from [<c06f46d8>] (schedule+0x9c/0xc0) [ 5.897129] [<c06f46d8>] (schedule) from [<c06f4904>] (schedule_preempt_disabled+0x14/0x20) [ 5.897140] [<c06f4904>] (schedule_preempt_disabled) from [<c06f64e4>] (mutex_lock_nested+0x258/0x43c) [ 5.897150] [<c06f64e4>] (mutex_lock_nested) from [<c05ce9c8>] (clk_prepare_lock+0x48/0xe0) [ 5.897160] [<c05ce9c8>] (clk_prepare_lock) from [<c05d0e7c>] (clk_prepare+0x10/0x28) [ 5.897169] [<c05d0e7c>] (clk_prepare) from [<c04c2668>] (omap_tll_enable+0x64/0xd0) [ 5.897180] [<c04c2668>] (omap_tll_enable) from [<c04c1728>] (usbhs_runtime_resume+0x18/0x17c) [ 5.897192] [<c04c1728>] (usbhs_runtime_resume) from [<c049d404>] (pm_generic_runtime_resume+0x2c/0x40) [ 5.897202] [<c049d404>] (pm_generic_runtime_resume) from [<c049f180>] (__rpm_callback+0x38/0x68) [ 5.897210] [<c049f180>] (__rpm_callback) from [<c049f220>] (rpm_callback+0x70/0x88) [ 5.897218] [<c049f220>] (rpm_callback) from [<c04a0a00>] (rpm_resume+0x4ec/0x7ec) [ 5.897227] [<c04a0a00>] (rpm_resume) from [<c04a0f48>] (__pm_runtime_resume+0x4c/0x64) [ 5.897236] [<c04a0f48>] (__pm_runtime_resume) from [<c04958dc>] (driver_probe_device+0x30/0x70) [ 5.897246] [<c04958dc>] (driver_probe_device) from [<c04959a4>] (__driver_attach+0x88/0xac) [ 5.897256] [<c04959a4>] (__driver_attach) from [<c04940f8>] (bus_for_each_dev+0x50/0x84) [ 5.897267] [<c04940f8>] (bus_for_each_dev) from [<c0494e40>] (bus_add_driver+0xcc/0x1e4) [ 5.897276] [<c0494e40>] (bus_add_driver) from [<c0496914>] (driver_register+0xac/0xf4) [ 5.897286] [<c0496914>] (driver_register) from [<c01018e0>] (do_one_initcall+0x100/0x1b8) [ 5.897296] [<c01018e0>] (do_one_initcall) from [<c01c7a54>] (do_init_module+0x58/0x1c0) [ 5.897304] [<c01c7a54>] (do_init_module) from [<c01c8a3c>] (SyS_finit_module+0x88/0x90) [ 5.897313] [<c01c8a3c>] (SyS_finit_module) from [<c0107120>] (ret_fast_syscall+0x0/0x1c) [ 5.912697] ------------[ cut here ]------------ [ 5.912711] WARNING: CPU: 0 PID: 994 at kernel/sched/core.c:2996 _raw_spin_unlock+0x28/0x58 [ 5.912717] DEBUG_LOCKS_WARN_ON(val > preempt_count()) Reported-by:
H. Nikolaus Schaller <hns@goldelico.com> Tested-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Vik Heyndrickx authored
commit 20878232 upstream. Systems show a minimal load average of 0.00, 0.01, 0.05 even when they have no load at all. Uptime and /proc/loadavg on all systems with kernels released during the last five years up until kernel version 4.6-rc5, show a 5- and 15-minute minimum loadavg of 0.01 and 0.05 respectively. This should be 0.00 on idle systems, but the way the kernel calculates this value prevents it from getting lower than the mentioned values. Likewise but not as obviously noticeable, a fully loaded system with no processes waiting, shows a maximum 1/5/15 loadavg of 1.00, 0.99, 0.95 (multiplied by number of cores). Once the (old) load becomes 93 or higher, it mathematically can never get lower than 93, even when the active (load) remains 0 forever. This results in the strange 0.00, 0.01, 0.05 uptime values on idle systems. Note: 93/2048 = 0.0454..., which rounds up to 0.05. It is not correct to add a 0.5 rounding (=1024/2048) here, since the result from this function is fed back into the next iteration again, so the result of that +0.5 rounding value then gets multiplied by (2048-2037), and then rounded again, so there is a virtual "ghost" load created, next to the old and active load terms. By changing the way the internally kept value is rounded, that internal value equivalent now can reach 0.00 on idle, and 1.00 on full load. Upon increasing load, the internally kept load value is rounded up, when the load is decreasing, the load value is rounded down. The modified code was tested on nohz=off and nohz kernels. It was tested on vanilla kernel 4.6-rc5 and on centos 7.1 kernel 3.10.0-327. It was tested on single, dual, and octal cores system. It was tested on virtual hosts and bare hardware. No unwanted effects have been observed, and the problems that the patch intended to fix were indeed gone. Tested-by:
Damien Wyart <damien.wyart@free.fr> Signed-off-by:
Vik Heyndrickx <vik.heyndrickx@veribox.net> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Doug Smythies <dsmythies@telus.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 0f004f5a ("sched: Cure more NO_HZ load average woes") Link: http://lkml.kernel.org/r/e8d32bff-d544-7748-72b5-3c86cc71f09f@veribox.netSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Jaegeuk Kim authored
commit b5a7aef1 upstream. This patch allows fscrypto to handle a second key prefix given by filesystem. The main reason is to provide backward compatibility, since previously f2fs used "f2fs:" as a crypto prefix instead of "fscrypt:". Later, ext4 should also provide key_prefix() to give "ext4:". One concern decribed by Ted would be kinda double check overhead of prefixes. In x86, for example, validate_user_key consumes 8 ms after boot-up, which turns out derive_key_aes() consumed most of the time to load specific crypto module. After such the cold miss, it shows almost zero latencies, which treats as a negligible overhead. Note that request_key() detects wrong prefix in prior to derive_key_aes() even. Cc: Ted Tso <tytso@mit.edu> Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Josh Poimboeuf authored
commit 4a6b27b7 upstream. Megha Dey reported a kernel panic in crypto code. The problem is that sha1_x8_avx2() clobbers registers r12-r15 without saving and restoring them. Before commit aec4d0e3 ("x86/asm/crypto: Simplify stack usage in sha-mb functions"), those registers were saved and restored by the callers of the function. I removed them with that commit because I didn't realize sha1_x8_avx2() clobbered them. Fix the potential undefined behavior associated with clobbering the registers and make the behavior less surprising by changing the registers to be callee saved/restored to conform with the C function call ABI. Also, rdx (aka RSP_SAVE) doesn't need to be saved: I verified that none of the callers rely on it being saved, and it's not a callee-saved register in the C ABI. Fixes: aec4d0e3 ("x86/asm/crypto: Simplify stack usage in sha-mb functions") Reported-by:
Megha Dey <megha.dey@linux.intel.com> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Andy Gross authored
commit 2a0974aa upstream. This patch adds the CLK_SET_RATE_PARENT flag for the crypto core and ahb blocks. Without this flag, clk_set_rate can fail for certain frequency requests. Signed-off-by:
Andy Gross <andy.gross@linaro.org> Fixes: 3966fab8 ("clk: qcom: Add MSM8916 Global Clock Controller support") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Corentin LABBE authored
commit bdb6cf9f upstream. The current sun4i-ss driver could generate data corruption when ciphering/deciphering. It occurs randomly on end of handled data. No root cause have been found and the only way to remove it is to replace all spin_lock_bh by their irq counterparts. Fixes: 6298e948 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator") Signed-off-by:
LABBE Corentin <clabbe.montjoie@gmail.com> Signed-off-by:
-
Horia Geant? authored
commit 3639ca84 upstream. Provide hardware state import/export functionality, as mandated by commit 8996eafd ("crypto: ahash - ensure statesize is non-zero") Reported-by:
Jonas Eymann <J.Eymann@gmx.net> Signed-off-by:
Horia Geant? <horia.geanta@nxp.com> Signed-off-by:
-
Catalin Vasile authored
commit e930c765 upstream. caam_jr_alloc() used to return NULL if a JR device could not be allocated for a session. In turn, every user of this function used IS_ERR() function to verify if anything went wrong, which does NOT look for NULL values. This made the kernel crash if the sanity check failed, because the driver continued to think it had allocated a valid JR dev instance to the session and at some point it tries to do a caam_jr_free() on a NULL JR dev pointer. This patch is a fix for this issue. Signed-off-by:
Catalin Vasile <cata.vasile@nxp.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 59643d15 upstream. If the size passed to ring_buffer_resize() is greater than MAX_LONG - BUF_PAGE_SIZE then the DIV_ROUND_UP() will return zero. Here's the details: # echo 18014398509481980 > /sys/kernel/debug/tracing/buffer_size_kb tracing_entries_write() processes this and converts kb to bytes. 18014398509481980 << 10 = 18446744073709547520 and this is passed to ring_buffer_resize() as unsigned long size. size = DIV_ROUND_UP(size, BUF_PAGE_SIZE); Where DIV_ROUND_UP(a, b) is (a + b - 1)/b BUF_PAGE_SIZE is 4080 and here 18446744073709547520 + 4080 - 1 = 18446744073709551599 where 18446744073709551599 is still smaller than 2^64 2^64 - 18446744073709551599 = 17 But now 18446744073709551599 / 4080 = 4521260802379792 and size = size * 4080 = 18446744073709551360 This is checked to make sure its still greater than 2 * 4080, which it is. Then we convert to the number of buffer pages needed. nr_page = DIV_ROUND_UP(size, BUF_PAGE_SIZE) but this time size is 18446744073709551360 and 2^64 - (18446744073709551360 + 4080 - 1) = -3823 Thus it overflows and the resulting number is less than 4080, which makes 3823 / 4080 = 0 an nr_pages is set to this. As we already checked against the minimum that nr_pages may be, this causes the logic to fail as well, and we crash the kernel. There's no reason to have the two DIV_ROUND_UP() (that's just result of historical code changes), clean up the code and fix this bug. Fixes: 83f40318 ("ring-buffer: Make removal of ring buffer pages atomic") Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
