As we move to 1:1 model and melt xen_netbk and xenvif together, it would
be better to use single prefix for all functions in xen-netback.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements 1:1 model netback. NAPI and kthread are utilized
to do the weight-lifting job:

- NAPI is used for guest side TX (host side RX)
- kthread is used for guest side RX (host side TX)

Xenvif and xen_netbk are made into one structure to reduce code size.

This model provides better scheduling fairness among vifs. It is also
prerequisite for implementing multiqueue for Xen netback.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The data flow from DomU to DomU on the same host in current copying
scheme with tracking facility:

       copy
DomU --------> Dom0          DomU
 |                            ^
 |____________________________|
             copy

The page in Dom0 is a page with valid MFN. So we can always copy from
page Dom0, thus removing the need for a tracking facility.

       copy           copy
DomU --------> Dom0 -------> DomU

Simple iperf test shows no performance regression (obviously we copy
twice either way):

  W/  tracking: ~5.3Gb/s
  W/o tracking: ~5.4Gb/s
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Matt Wilson <msw@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesse Gross says:

====================
A number of significant new features and optimizations for net-next/3.12.
Highlights are:
 * "Megaflows", an optimization that allows userspace to specify which
   flow fields were used to compute the results of the flow lookup.
   This allows for a major reduction in flow setups (the major
   performance bottleneck in Open vSwitch) without reducing flexibility.
 * Converting netlink dump operations to use RCU, allowing for
   additional parallelism in userspace.
 * Matching and modifying SCTP protocol fields.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter updates for your net-next tree,
they are:

* The new SYNPROXY target for iptables, including IPv4 and IPv6 support,
  from Patrick McHardy.

* nf_defrag_ipv6.o should be only linked to nf_defrag_ipv6.ko, from
  Nathan Hintz.

* Fix an old bug in REJECT, which replies with wrong MAC source address
  from the bridge, by Phil Oester.

* Fix uninitialized helper variable in the expectation support over
  nfnetlink_queue, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
More refactoring and cleanup, particularly around filter management.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

net/netfilter/nf_conntrack_netlink.c: In function 'ctnetlink_nfqueue_attach_expect':
'helper' may be used uninitialized in this function

It was only initialized in if CTA_EXPECT_HELP_NAME attribute was
present, it must be NULL otherwise.

Problem added recently in bd077937
(netfilter: nfnetlink_queue: allow to attach expectations to conntracks).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add an IPv6 version of the SYNPROXY target. The main differences to the
IPv4 version is routing and IP header construction.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Martin Topholm <mph@one.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Extract the local TCP stack independant parts of tcp_v6_init_sequence()
and cookie_v6_check() and export them for use by the upcoming IPv6 SYNPROXY
target.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Martin Topholm <mph@one.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add a SYNPROXY for netfilter. The code is split into two parts, the synproxy
core with common functions and an address family specific target.

The SYNPROXY receives the connection request from the client, responds with
a SYN/ACK containing a SYN cookie and announcing a zero window and checks
whether the final ACK from the client contains a valid cookie.

It then establishes a connection to the original destination and, if
successful, sends a window update to the client with the window size
announced by the server.

Support for timestamps, SACK, window scaling and MSS options can be
statically configured as target parameters if the features of the server
are known. If timestamps are used, the timestamp value sent back to
the client in the SYN/ACK will be different from the real timestamp of
the server. In order to now break PAWS, the timestamps are translated in
the direction server->client.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Martin Topholm <mph@one.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Extract the local TCP stack independant parts of tcp_v4_init_sequence()
and cookie_v4_check() and export them for use by the upcoming SYNPROXY
target.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Martin Topholm <mph@one.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Split out sequence number adjustments from NAT and move them to the conntrack
core to make them usable for SYN proxying. The sequence number adjustment
information is moved to a seperate extend. The extend is added to new
conntracks when a NAT mapping is set up for a connection using a helper.

As a side effect, this saves 24 bytes per connection with NAT in the common
case that a connection does not have a helper assigned.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Martin Topholm <mph@one.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

'nf_defrag_ipv6' is built as a separate module; it shouldn't be
included in the 'nf_conntrack_ipv6' module as well.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

As reported by Casper Gripenberg, in a bridged setup, using ip[6]t_REJECT
with the tcp-reset option sends out reset packets with the src MAC address
of the local bridge interface, instead of the MAC address of the intended
destination.  This causes some routers/firewalls to drop the reset packet
as it appears to be spoofed.  Fix this by bypassing ip[6]_local_out and
setting the MAC of the sender in the tcp reset packet.

This closes netfilter bugzilla #531.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Make sure the sw_flow_key structure and valid mask boundaries are always
machine word aligned. Optimize the flow compare and mask operations
using machine word size operations. This patch improves throughput on
average by 15% when CPU is the bottleneck of forwarding packets.

This patch is inspired by ideas and code from a patch submitted by Peter
Klausler titled "replace memcmp() with specialized comparator".
However, The original patch only optimizes for architectures
support unaligned machine word access. This patch optimizes for all
architectures.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

Steven (cc-ed) noticed an imbalance in semaphore put/get for
82573-based NICs. Don't we need something like the following
(untested) patch?
Signed-off-by: Steven La <sla@riverbed.com>
Acked-by: Arthur Kepner <akepner@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updates the documentation to the Intel wired LAN drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the firmware to address the thermal notification issue
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for virtual IOMMU to the vmxnet3 module.  We
switch to DMA consistent mappings for anything we pass to the device.
There were a few places where we already did this, but using pci_blah();
these have been fixed to use dma_blah(), along with all new occurrences
where we've replaced kmalloc() and friends.

Also fix two small bugs:
1) use after free of rq->buf_info in vmxnet3_rq_destroy()
2) a cpu_to_le32() that should have been a cpu_to_le64()
Acked-by: George Zhang <georgezhang@vmware.com>
Acked-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support is provided only for combined channels. When SR-IOV is not
enabled, BE3 supports upto 16 channels and Lancer-R/SH-R support upto
32 channels.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) Move be_cmd_if_create() above queue create routines to allow
   TXQ creation (that requires if_handle) to be clubbed with TX-CQ creation.
2) Consolidate all queue create routines into be_setup_queues()
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the IF_CREATE FW cmd is issued only *after* MCCQ is created as
it was coded to only use MCCQ. By fixing this, cmd_if_create() can be
called before MCCQ is created and the same routine for VF provisioning
can be called after.
This allows for consolidating all the queue create routines by moving
the be_cmd_if_create() call above all queue create calls in be_setup().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) use be_resources{} struct to query/store HW resource limits
2) The HW queue/resource limits for BE2/BE3 chips are mostly called out
   in driver as constants.  Code to handle this is scattered across various
   places in be_setup(). Consolidate this code into BEx_get_resources().
   For Lancer-R, Skyhawk-R, these limits are queried from FW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) Parse PCIe descriptor for max-VFs supported by HW
2) Cleanup NIC descriptor parsing in get_func/profile_config() routines
3) Use common struct definitions for v0 and v1 versions of GET_FUNC_CONFIG
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

EQ_CREATEv2 explicitly returns the msix-index associated with a EQ.
For SH-R this is needed if EQs need to be deleted and re-created without
resetting a function.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the tcp_probe snooper can either filter packets by a given
port (handed to the module via module parameter e.g. port=80) or lets
all TCP traffic pass (port=0, default). When a port is specified, the
port number is tested against the sk's source/destination port. Thus,
if one of them matches, the information will be further processed for
the log.

As this is quite limited, allow for more advanced filtering possibilities
which can facilitate debugging/analysis with the help of the tcp_probe
snooper. Therefore, similarly as added to BPF machine in commit 7e75f93e
("pkt_sched: ingress socket filter by mark"), add the possibility to
use skb->mark as a filter.

If the mark is not being used otherwise, this allows ingress filtering
by flow (e.g. in order to track updates from only a single flow, or a
subset of all flows for a given port) and other things such as dynamic
logging and reconfiguration without removing/re-inserting the tcp_probe
module, etc. Simple example:

  insmod net/ipv4/tcp_probe.ko fwmark=8888 full=1
  ...
  iptables -A INPUT -i eth4 -t mangle -p tcp --dport 22 \
           --sport 60952 -j MARK --set-mark 8888
  [... sampling interval ...]
  iptables -D INPUT -i eth4 -t mangle -p tcp --dport 22 \
           --sport 60952 -j MARK --set-mark 8888

The current option to filter by a given port is still being preserved. A
similar approach could be done for the sctp_probe module as a follow-up.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Adapter and driver supports only CEE dcbnl ops. Only GET callbacks
  within dcbnl ops are supported currently.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Adapter sends Asynchronous Event Notifications to the driver when
  there are changes in the switch or adapter DCBX configuration.
  AEN handler updates the driver DCBX parameters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Populate driver data structures with local, operational, and peer
  DCB parameters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Query adapter DCB capabilities and  populate local data structures
  with relevant information.

o Add QLCNIC_DCB to Kconfig for enabling/disabling DCB.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
1. Refactoring and cleanup in preparation for new hardware support.
2. Some bug fixes for firmware completion handling.  (They're not known
to cause real problems, otherwise I'd be submitting these for net and
stable.)
3. Update to the firmware protocol (MCDI) definitions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Key_end is a better name describing the ending boundary than key_len.
Rename those variables to make it less confusing.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

This patch adds support for rewriting SCTP src,dst ports similar to the
functionality already available for TCP/UDP.

Rewriting SCTP ports is expensive due to double-recalculation of the
SCTP checksums; this is performed to ensure that packets traversing OVS
with invalid checksums will continue to the destination with any
checksum corruption intact.
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

Conflicts:
	drivers/net/wireless/iwlwifi/pcie/trans.c
	include/linux/inetdevice.h

The inetdevice.h conflict involves moving the IPV4_DEVCONF values
into a UAPI header, overlapping additions of some new entries.

The iwlwifi conflict is a context overlap.
Signed-off-by: David S. Miller <davem@davemloft.net>

Boris BREZILLON says:

====================
net/cadence/macb: add support for dt phy definition

This patch series adds support for ethernet phy definition using device
tree.

This may help in moving some at91 boards to dt (some of them define an
interrupt pin).

Tested on samad31ek.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch describe the phy used on atmel sama5d3 mother board:
 - phy address
 - phy interrupt pin
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The macb driver only handle PHY description through platform_data
(macb_platform_data).
Thus, when using dt you cannot define phy properties like phy address or
phy irq pin.

This patch makes use of the of_mdiobus_register to add support for
phy device definition using dt.
A fallback to the autoscan procedure is added in case there is no phy
devices defined in dt.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says that my previous fix for an ERR_PTR dereference
(ea857f28 'ipip: dereferencing an ERR_PTR in ip_tunnel_init_net()')
could be racy and suggests the following fix instead.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return a negative error code in the add bond vlan ids error
handling case instead of 0, as done elsewhere in this function.

Introduced by commit 1ff412ad.
(bonding: change the bond's vlan syncing functions with the standard ones)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>