I found no references to SMBus in ACPI DSDT disassembly on my laptop
so this should be safe.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Some BIOSes hide 'overflow' device (dev #6) for i82875P/PE chipsets.
The same happens for i82865P/PE. Add a quirk to enable this device.
This allows i82875 EDAC driver to bind to chipset's dev #6 and not
dev #0 as the latter is used by AGP driver.

On my laptop (i82865P based) ACPI code is disabling this device
again in \_SB.PCI0._CRS method (called at least at PNP init time).
This can be easily worked around by patching DSDT.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Acked-by: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Addition of one unknown subsystem identifier to the quirks handler for
chipset i82855GM_HB on notebook Asus A6L. This exposes the otherwise
hidden SMBus controller within the south bridge ICH4-M.
Signed-off-by: Mats Erik Andersson <mats.andersson@gisladisker.se>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC).  This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.

The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).

Turning ECRC on or off can be a data integrity versus performance
tradeoff.  In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

According to the PCI PM specification (PCI Bus Power Management
Interface Specification, Rev. 1.2, Section 5.4.1) we are supposed to
reinitialize devices that have PCI_PM_CTRL_NO_SOFT_RESET clear during
all transitions from PCI_D3hot to PCI_D0, but we only do it if the
device's current_state field is equal to PCI_UNKNOWN.

This may lead to problems if a device with PCI_PM_CTRL_NO_SOFT_RESET
unset is put into PCI_D3hot at run time by its driver and
pci_set_power_state() is used to put it back into PCI_D0, because in
that case the device will remain uninitialized after
pci_set_power_state() has returned.  Prevent that from happening by
modifying pci_raw_set_power_state() to reinitialize devices with
PCI_PM_CTRL_NO_SOFT_RESET unset during all transitions from D3 to D0.

Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCIe root complex integrated endpoint does not implement ARI, so this
kind of endpoint uses 3-bit function number. The function dependency
link of the integrated endpoint should be calculated using the device
number plus the value from function dependency link register.

Normal endpoint always implements ARI and the function dependency link
register contains 8-bit function number (i.e. `devfn' from software's
perspective).
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

We always call pci_stop_bus_device before calling pci_destroy_dev.

Since pci_stop_bus_device calls pci_stop_dev, there is no need
for pci_destroy_dev to repeat the call.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pci_enable_msix currently returns -EINVAL if you ask
for more vectors than supported by the device, which would
typically cause fallback to regular interrupts.

It's better to return the table size, making the driver retry
MSI-X with less vectors.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

VIA has a strange chipset, it has root port under a bridge. Disable ASPM
for such strange chipset.

Cc: stable@kernel.org
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

At this point, it seems to solve more problems than it causes, so let's try using it by default.  It's an easy revert if it ends up causing trouble.
Reviewed-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

The last in-tree caller of pci_find_slot has been converted, so
let's get rid of this deprecated interface.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Convert uses of pci_find_slot to modern API.

In the conversion sites, we end up calling pci_dev_put() right away.

This may seem like it misses the entire point of doing something like
pci_get_bus_and_slot(), since we drop the reference so soon, but it turns
out we don't actually do much with the returned pci_dev.

I plan on untangling cpqphp further, but clearly cpqphp never worried too
much about a properly refcounted pci_dev anyway. For now, this conversion
seems reasonable, as it gets rid of the last in-tree caller of pci_find_slot.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Eliminate this warning:
	warning: return discards qualifiers from pointer target type
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

I have no clue what the original intent here was, but the code as
written is useless.

The old dbg() statement above the old callsite might lead one to think
that at one point, there was supposed to be some recursion, but any
sense of sanity here has been lost to the ravages of time.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Instead of making multiple calls to pcibios_get_irq_routing_table, let's
just do it once and save the answer.

The reason we were making multiple calls is because we liked to calculate
its length and perform some loop over it. Instead of open-coding the length
calculation every time, provide it in an inline helper function.

Finally, since pci_print_IRQ_route() is used only for debug, let's only
do it when cpqhp_debug is set.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Handle an empty slot at the top of the loop, and continue early.

This allows us to un-indent the rest of the function by one level.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Clean up style, whitespace in cpqphp_pci.c
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Check for an empty slot, and return early if so.

This allows us to un-indent the rest of the function by one level.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Style and whitespace cleanups, no functional change.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Apply DeMorgan's theorem:

	if ((pdev->revision > 2) || (vendor_id == PCI_VENDOR_ID_INTEL))

turns into

	if ((pdev->revision <= 2) && (vendor_id != PCI_VENDOR_ID_INTEL))

Now we can bail out early from the function if the controller is not
supported.

This allows us to un-indent the remainder of the function quite a bit and
make it much more readable.

Fix up some extra braces, and un-indent the 'case' labels in the switch
statement as per CodingStyle.

No functional change.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Clean up style and eliminate superfluous braces and parens.

No functional change.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Impact: refactor

Refactor code to follow convention more closely and eliminate the need
for some useless prototypes.

No functional change.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Clean up cpqphp.h to follow 80 column convention.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Fix up comments from C++ to C-style, wrapping if necessary, etc.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Clean up all stray whitespace issues, such as trailing whitespace,
spaces before tabs, etc. and whatever else vim's c_space_errors
highlights in red.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

We could run out of space under under 4g, but devices under transparent
bridges can use 64bit resources, so keep trying on the parent bus until
we hit a non-transparent bridge.

Impact: better support for assigning unassigned resources
Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

We should not assign 64bit ranges to PCI devices that only take 32bit
prefetchable addresses.

Try to set IORESOURCE_MEM_64 in 64bit resource of pci_device/pci_bridge
and make the bus resource only have that bit set when all devices under
it support 64bit prefetchable memory.  Use that flag to allocate
resources from that range.
Reported-by: Yannick <yannick.roehlly@free.fr>
Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Impact: cleanup, improve readability

Define PCI_MSI_MASK_32/64 for 32/64bit devices, instead of using
implicit offset (-4), "PCI_MSI_MASK_BIT - 4" and "PCI_MSI_MASK_BIT".
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

drivers/pci/hotplug/ibmphp_core.c:1414: warning: `ibmphp_exit' defined but not used
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Impact: cleanup, spec compliance

This patch does:

 - Remove unused msi/msix_enable/disable macros.
   User should use msi/msix_set_enable() functions instead.

 - Remove unused msix_mask/unmask/pending macros.
   These macros are useless because they are not based on any of
   the PCI Local Bus Specifications properly.
   It seems that they were written based on a draft of PCI spec,
   and that the draft was the MSI-X ECN that underwent membership
   review in September 2002.
   (* In the draft, the size of a entry in MSI-X table was 64bit,
      containing 32bit message data and DWORD aligned lower address
      plus a pending bit and a mask bit.(30+1+1bit)  The higher
      address was placed in MSI-X capability structure and shared
      by all entries.)

 - Remove PCI_MSIX_FLAGS_BITMASK.
   This definition also come from the draft ECN.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.

mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card.  I have tested this, and removing the !
fixes the problem.

Cc: "Peter Botha" <peterb@goldcircle.co.za>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit code, we scan buffers attached to a transaction.  During this
scan, we sometimes have to drop j_list_lock and then we recheck whether
the journal buffer head didn't get freed by journal_try_to_free_buffers().
 But checking for buffer_jbd(bh) isn't enough because a new journal head
could get attached to our buffer head.  So add a check whether the journal
head remained the same and whether it's still at the same transaction and
list.

This is a nasty bug and can cause problems like memory corruption (use after
free) or trigger various assertions in JBD code (observed).
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The recent ->lookup() deadlock correction required the directory inode
mutex to be dropped while waiting for expire completion.  We were
concerned about side effects from this change and one has been identified.

I saw several error messages.

They cause autofs to become quite confused and don't really point to the
actual problem.

Things like:

handle_packet_missing_direct:1376: can't find map entry for (43,1827932)

which is usually totally fatal (although in this case it wouldn't be
except that I treat is as such because it normally is).

do_mount_direct: direct trigger not valid or already mounted
/test/nested/g3c/s1/ss1

which is recoverable, however if this problem is at play it can cause
autofs to become quite confused as to the dependencies in the mount tree
because mount triggers end up mounted multiple times.  It's hard to
accurately check for this over mounting case and automount shouldn't need
to if the kernel module is doing its job.

There was one other message, similar in consequence of this last one but I
can't locate a log example just now.

When checking if a mount has already completed prior to adding a new mount
request to the wait queue we check if the dentry is hashed and, if so, if
it is a mount point.  But, if a mount successfully completed while we
slept on the wait queue mutex the dentry must exist for the mount to have
completed so the test is not really needed.

Mounts can also be done on top of a global root dentry, so for the above
case, where a mount request completes and the wait queue entry has already
been removed, the hashed test returning false can cause an incorrect
callback to the daemon.  Also, d_mountpoint() is not sufficient to check
if a mount has completed for the multi-mount case when we don't have a
real mount at the base of the tree.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The massive nommu update (8feae131) resulted in these warnings:
ipc/shm.c: In function `sys_shmdt':
ipc/shm.c:974: warning: unused variable `size'
ipc/shm.c:972: warning: unused variable `next'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  kvm: fix kvm reboot crash when MAXSMP is used
  cpumask: alloc zeroed cpumask for static cpumask_var_ts
  cpumask: introduce zalloc_cpumask_var

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  bsg: setting rq->bio to NULL

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  cls_cgroup: Fix oops when user send improperly 'tc filter add' request
  r8169: fix crash when large packets are received

* 'for-linus' of git://neil.brown.name/md:
  md/raid5: fix bug in reshape code when chunk_size decreases.
  md/raid5 - avoid deadlocks in get_active_stripe during reshape
  md/raid5: use conf->raid_disks in preference to mddev->raid_disk