Switch demod resource use from exported symbols to callbacks its
provides.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add callback for all of those functions which are currently
exported using EXPORT_SYMBOL. That allows us convert every user to
callbacks and eventually all exported symbols could be removed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use regmap to cover register access routines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Own I2C locking is needed due to two special reasons:
1) Chips uses multiple register pages/banks on single I2C slave.
Page is changed via I2C register access.
2) Chip offers muxed/gated I2C adapter for tuner. Gate/mux is
controlled by I2C register access.

Due to these reasons, I2C locking did not fit very well.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

RTL2830 demod integrated to RTL2831U has PID filter. PID filtering
is provided by rtl2830 demod driver. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Implement PID filter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 read SNR to return values calculated by DVBv5
statistics.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 read BER to return values calculated by DVBv5
statistics.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Change legacy DVBv3 signal strength to return values calculated by
DVBv5 statistics.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBv5 BER.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Estimate signal strength from IF AGC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBv5 CNR.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Trivial changes proposed by checkpatch.pl and some more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove internal config and use configuration values directly from
the platform data.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Pass correct device for dev_foo() logging in order to print logs
correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

As a I2C driver struct i2c_client is top level structure representing
the driver. Use it as parameter to carry all needed information for
each function in order to simplify things.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use name 'dev' for device state instance as it is more common and
also one letter shorter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove legacy DVB binding as all users are using I2C binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

rtl2830 driver supports now I2C model too. Start using it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert driver to kernel I2C model. Old DVB proprietary model is
still left there also.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Top level pointer on USB probe is struct usb_interface *. Add that
pointer to struct dvb_usb_device that drivers could use it, for
dev_* logging and more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Although IRQ_HANDLED is "safe" value to return,
it is better to let the kernel know whether the driver handle the interrupt or not.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/platform/am437x/am437x-vpfe.c:2767:3-8: No need to set .owner here. The core will do it.

 Remove .owner field if calls are used which set it automatically

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

CC: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The mmp ccic driver expects a platform_data structure that does not exist
in the mainline kernel and presumably was changed in a kernel fork, which
leads to build errors now:

media/platform/marvell-ccic/mmp-driver.c: In function 'mmpcam_calc_dphy':
media/platform/marvell-ccic/mmp-driver.c:252:15: error: 'struct mmp_camera_platform_data' has no member named 'dphy3_algo'
  switch (pdata->dphy3_algo) {
               ^
media/platform/marvell-ccic/mmp-driver.c:253:7: error: 'DPHY3_ALGO_PXA910' undeclared (first use in this function)
  case DPHY3_ALGO_PXA910:
       ^
media/platform/marvell-ccic/mmp-driver.c:253:7: note: each undeclared identifier is reported only once for each function it appears in
media/platform/marvell-ccic/mmp-driver.c:257:8: error: 'struct mmp_camera_platform_data' has no member named 'dphy'

This marks the driver as 'BROKEN' but keeps the code around.
Alternatively it could be removed entirely.

Fixes: 05fed816 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Libin Yang <lbyang@marvell.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

[media] staging: bcm2048: Delete an unnecessary check before the function call "video_unregister_device"

The video_unregister_device() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

1: Simplify the vpe mem-to-mem driver by using the m2m ioctl
   and vb2 helpers.
2: Align and arranged the v4l2_ioctl_ops.
3: Fixes a typo.
4: Use of_match_ptr() instead of explicitly defining the macro
   to NULL in case CONFIG_OF is not defined.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

X-Patchwork-Delegate: m.chehab@samsung.com
As shown at the code, upd_demod_gain_period is used to write
to two 16-bit registers:
    dib8000_write_word(state, 1946, upd_demod_gain_period & 0xFFFF);
    dib8000_write_word(state, 1947, reg | (1<<14) | ((upd_demod_gain_period >> 16) & 0xFF));

So, it should be declared as u32.

This fixes the following smatch warning:
	drivers/media/dvb-frontends/dib8000.c:1282 dib8000_agc_startup() warn: right shifting more than type allows
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

As reported by smatch:
	drivers/media/pci/cx23885/cx23885-dvb.c:2080 dvb_register() Function too hairy.  Giving up.

This is indeed a too complex function, with lots of stuff inside.
Breaking this into two functions makes it a little bit less hairy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert au0828 to use videobuf2. Tested with NTSC.
Tested video and vbi devices with xawtv, tvtime,
and vlc. Ran v4l2-compliance to ensure there are
no failures.

Video compliance test results summary:
Total: 75, Succeeded: 75, Failed: 0, Warnings: 18

Vbi compliance test results summary:
Total: 75, Succeeded: 75, Failed: 0, Warnings: 0
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

au0828 picked up UNSET from videobuf-core.h and fails to compile
if videobuf-core.h isn't included. Change it to use -1U instead
to fix the problem.

    drivers/media/usb/au0828/au0828-cards.c:47:17: error: ‘UNSET’ undeclared here (not in a function)
       .tuner_type = UNSET,
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

au0828_analog_register() frees au0828_dev when it fails to
locate isoc endpoint. au0828_usb_probe() continues with dvb
and rc probe and registration assuming dev is still valid.
When au0828_analog_register() fails to locate isoc endpoint,
it should return without free'ing au0828_dev. Otherwise, the
probe will fail as dev is null when au0828_dvb_register() is
called.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add myself as the maintainer for the adv7180 video subdev driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

In fast switch mode the adv7180 (and similar) can lock onto a new signal
faster when switching between different inputs. As a downside though it is
no longer able to auto-detect the incoming format.

The fast switch mode is exposed as a boolean v4l control that allows
userspace applications to either enable or disable fast switch mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Some of the devices supported by this driver have a interlaced-to-
progressive converter which can optionally be enabled. This patch adds
support for enabling and disabling the I2P converter on such devices.

I2P mode can be enabled by selecting V4L2_FIELD_NONE instead of
V4L2_FIELD_INTERLACED for the format.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds support for the adv7280-m/adv2781-m/adv7281-ma/adv7282-m
devices to the adv7180 driver. They are very similar to the
adv7280/adv7281/adv7282 but instead of parallel video out they feature a
MIPI CSI2 transmitter.

The CSI2 transmitter is configured via a separate I2C address, so we need to
register a dummy device for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds support for the adv7280/adv7281/adv7282 devices to the
adv7180 driver. They are very similar to the adv7182, the main difference
from the drivers point of view are some different tuning constants for
improved video performance.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds support for the adv7182 to the adv7180 driver. The adv7182
is similar to the adv7180, the main difference from the driver's point of
view is how the video input and how the input format are selected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The adv7180 is part of a larger family of device, which have all a very
similar register map layout. This patch prepares the adv7180 driver for
support for multiple different devices. For now the only difference we care
about is the number of input channel configurations. Also the way the input
format is configured slightly differs between some devices.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

We have basically the same code to set the video standard in init_device()
and adv7180_s_std(). Factor this out into a common helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add media controller support to the adv7180 driver by registering a media
entity instance for it as well as implementing pad ops for configuring the
format.

As there currently don't seem to be any users of the video ops format
operations those are removed as well in this patch.

Also set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so it is
possible to create a subdevice device node.

Since the driver now depends on VIDEO_V4L2_SUBDEV_API all drivers which
select the driver need to depend on that symbol as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>