Make sure to actually suspend the device before returning after a failed
(or deferred) probe.

Note that autosuspend must be disabled before runtime pm is disabled in
order to balance the usage count due to a negative autosuspend delay as
well as to make the final put suspend the device synchronously.

Fixes: 388bc262 ("omap-serial: Fix the error handling in the omap_serial probe")
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An unbalanced and misplaced synchronous put was used to suspend the
device on driver unbind, something which with a likewise misplaced
pm_runtime_disable leads to external aborts when an open port is being
removed.

Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa024010
...
[<c046e760>] (serial_omap_set_mctrl) from [<c046a064>] (uart_update_mctrl+0x50/0x60)
[<c046a064>] (uart_update_mctrl) from [<c046a400>] (uart_shutdown+0xbc/0x138)
[<c046a400>] (uart_shutdown) from [<c046bd2c>] (uart_hangup+0x94/0x190)
[<c046bd2c>] (uart_hangup) from [<c045b760>] (__tty_hangup+0x404/0x41c)
[<c045b760>] (__tty_hangup) from [<c045b794>] (tty_vhangup+0x1c/0x20)
[<c045b794>] (tty_vhangup) from [<c046ccc8>] (uart_remove_one_port+0xec/0x260)
[<c046ccc8>] (uart_remove_one_port) from [<c046ef4c>] (serial_omap_remove+0x40/0x60)
[<c046ef4c>] (serial_omap_remove) from [<c04845e8>] (platform_drv_remove+0x34/0x4c)

Fix this up by resuming the device before deregistering the port and by
suspending and disabling runtime pm only after the port has been
removed.

Also make sure to disable autosuspend before disabling runtime pm so
that the usage count is balanced and device actually suspended before
returning.

Note that due to a negative autosuspend delay being set in probe, the
unbalanced put would actually suspend the device on first driver unbind,
while rebinding and again unbinding would result in a negative
power.usage_count.

Fixes: 7e9c8e7d ("serial: omap: make sure to suspend device before remove")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The UPF_BOOT_AUTOCONF flag is needed for proper
flow control support.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Spinlock taken only for dma_map_single() for TX buffer is completely
useless and doesn't protect anything, so remove it to simplify the code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds missing checks for dma_map_single() failure and proper error
reporting. Although this issue was harmless on ARM architecture, it is always
good to use the DMA mapping API in a proper way. This patch fixes the following
DMA API debug warning:

WARNING: CPU: 1 PID: 3785 at lib/dma-debug.c:1171 check_unmap+0x8a0/0xf28
dma-pl330 121a0000.pdma: DMA-API: device driver failed to check map error[device address=0x000000006e0f9000] [size=4096 bytes] [mapped as single]
Modules linked in:
CPU: 1 PID: 3785 Comm: (agetty) Tainted: G        W       4.11.0-rc1-00137-g07ca963-dirty #59
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c072a114>] (check_unmap+0x8a0/0xf28)
[<c072a114>] (check_unmap) from [<c072a834>] (debug_dma_unmap_page+0x98/0xc8)
[<c072a834>] (debug_dma_unmap_page) from [<c0803874>] (s3c24xx_serial_shutdown+0x314/0x52c)
[<c0803874>] (s3c24xx_serial_shutdown) from [<c07f5124>] (uart_port_shutdown+0x54/0x88)
[<c07f5124>] (uart_port_shutdown) from [<c07f522c>] (uart_shutdown+0xd4/0x110)
[<c07f522c>] (uart_shutdown) from [<c07f6a8c>] (uart_hangup+0x9c/0x208)
[<c07f6a8c>] (uart_hangup) from [<c07c426c>] (__tty_hangup+0x49c/0x634)
[<c07c426c>] (__tty_hangup) from [<c07c78ac>] (tty_ioctl+0xc88/0x16e4)
[<c07c78ac>] (tty_ioctl) from [<c03b5f2c>] (do_vfs_ioctl+0xc4/0xd10)
[<c03b5f2c>] (do_vfs_ioctl) from [<c03b6bf4>] (SyS_ioctl+0x7c/0x8c)
[<c03b6bf4>] (SyS_ioctl) from [<c010b4a0>] (ret_fast_syscall+0x0/0x3c)
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Fixes: 62c37eed ("serial: samsung: add dma reqest/release functions")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Driver should provide its own struct device for all DMA-mapping calls instead
of extracting device pointer from DMA engine channel. Although this is harmless
from the driver operation perspective on ARM architecture, it is always good
to use the DMA mapping API in a proper way. This patch fixes following DMA API
debug warning:

WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1241 check_sync+0x520/0x9f4
samsung-uart 12c20000.serial: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000006df0f580] [size=64 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1-00137-g07ca963 #51
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c011aaa4>] (unwind_backtrace) from [<c01127c0>] (show_stack+0x20/0x24)
[<c01127c0>] (show_stack) from [<c06ba5d8>] (dump_stack+0x84/0xa0)
[<c06ba5d8>] (dump_stack) from [<c0139528>] (__warn+0x14c/0x180)
[<c0139528>] (__warn) from [<c01395a4>] (warn_slowpath_fmt+0x48/0x50)
[<c01395a4>] (warn_slowpath_fmt) from [<c0729058>] (check_sync+0x520/0x9f4)
[<c0729058>] (check_sync) from [<c072967c>] (debug_dma_sync_single_for_device+0x88/0xc8)
[<c072967c>] (debug_dma_sync_single_for_device) from [<c0803c10>] (s3c24xx_serial_start_tx_dma+0x100/0x2f8)
[<c0803c10>] (s3c24xx_serial_start_tx_dma) from [<c0804338>] (s3c24xx_serial_tx_chars+0x198/0x33c)
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Fixes: 62c37eed ("serial: samsung: add dma reqest/release functions")
CC: stable@vger.kernel.org # v4.0+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the UART is operated in DTE mode and UCR3_DCD or UCR3_RI are 1 (which
is the reset default) and the opposite side pulls the respective line to
its active level the irq triggers after it is requested in .probe.

These irqs were already disabled in .startup but this might be too late.

Also setup of the UFCR_DCEDTE bit (currently done in .set_termios) is
done very late which is critical as it also controls direction of some
pins.

So setup UFCR_DCEDTE earlier (in .probe) and also disable the broken
irqs in DTE mode there before requesting irqs.
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On SMP systems, we see a lot of spurious TX interrupts when a
program generates a steady stream of output to the pl011 UART.

The problem can be easily seen when one CPU generates the output
while another CPU handles the pl011 interrupts, and the rate of
output is low enough not to fill the TX FIFO. The problem seems
to be:

    -- CPU a --                        -- CPU b --
   (take port lock)
   pl011_start_tx
      pl011_start_tx_pio
         enable TXIM in REG_IMSC   ->  causes uart tx intr (pl011_int)
         pl011_tx_chars                pl011_int
            ...tx chars, all done...       (wait for port lock)
            pl011_stop_tx                   .
               disable TXIM                 .
    (release port lock)            ->      (take port lock)
                                           check for TXIM, not enabled
                                           (release port lock)
                                           return IRQ_NONE

Enabling the TXIM in pl011_start_tx_pio() causes the interrupt
to be generated and delivered to CPU b, even though pl011_tx_chars()
is able to complete the TX and then disable the tx interrupt.

Fix this by enabling TXIM only after pl011_tx_chars, if it is needed.
pl011_tx_chars will return a boolean indicating whether the TX
interrupts have to be enabled.
Debugged-by: Vijaya Kumar <Vijaya.Kumar@cavium.com>
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When Power management is disabled then the clocks are not getting
enabled. This patch enables it for the !PM case also.
While at it also pm_runtime_set_active is called before
calling pm_runtime_enable.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.

This will make it one place source for easier maintenance or
modifications.

While here, replace printk(KERN_INFO ) by pr_info(). It seems last printk()
call in serial_core.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't allow modifications of port name. It's serial core's business only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add serdev_device_write() a blocking call allowing to transfer
arbitraty amount of data (potentially exceeding amount that
serdev_device_write_buf can process in a single call)

To support that, also add serdev_device_write_wakeup().

Drivers wanting to use full extent of serdev_device_write
functionality are expected to provide serdev_device_write_wakeup() as
a sole handler of .write_wakeup event or call it as a part of driver's
custom .write_wakeup code.

Because serdev_device_write() subroutine is a superset of
serdev_device_write_buf() the patch re-impelements latter is terms of
the former. For drivers wanting to just use serdev_device_write_buf()
.write_wakeup handler is optional.

Cc: cphealy@gmail.com
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SPRD_TIMEOUT was 256, which is too small to wait until the status
switched to workable in a while loop, so that the earlycon could
not work correctly.
Signed-off-by: Wei Qiao <wei.qiao@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SC9860 use the same serial device which SC9836 uses, so added a new
compatible string to support SC9860 as well, also added an example
of how to describe this serial device in DT.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added bindings for Spreadtrum SP9860G board and SC9860 SoC.
This patch also revised bindings of SC9836 to make the format
more clear.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the serial fixes in here as well to handle merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull dmaengine fixes from Vinod Koul:
 "A couple of minor fixes for 4.11:

   - array bound fix for __get_unmap_pool()

   - cyclic period splitting for bcm2835"

* tag 'dmaengine-fix-4.11-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: Fix array index out of bounds warning in __get_unmap_pool()
  dmaengine: bcm2835: Fix cyclic DMA period splitting

Pull x86 fixes from Thomas Gleixner:
 "This update provides:

   - prevent KASLR from randomizing EFI regions

   - restrict the usage of -maccumulate-outgoing-args and document when
     and why it is required.

   - make the Global Physical Address calculation for UV4 systems work
     correctly.

   - address a copy->paste->forgot-edit problem in the MCE exception
     table entries.

   - assign a name to AMD MCA bank 3, so the sysfs file registration
     works.

   - add a missing include in the boot code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Include missing header file
  x86/mce/AMD: Give a name to MCA bank 3 when accessed with legacy MSRs
  x86/build: Mostly disable '-maccumulate-outgoing-args'
  x86/mm/KASLR: Exclude EFI region from KASLR VA space randomization
  x86/mce: Fix copy/paste error in exception table entries
  x86/platform/uv: Fix calculation of Global Physical Address

Pull scheduler fixes from Thomas Gleixner:
 "This update provides:

   - make the scheduler clock switch to unstable mode smooth so the
     timestamps stay at microseconds granularity instead of switching to
     tick granularity.

   - unbreak perf test tsc by taking the new offset into account which
     was added in order to proveide better sched clock continuity

   - switching sched clock to unstable mode runs all clock related
     computations which affect the sched clock output itself from a work
     queue. In case of preemption sched clock uses half updated data and
     provides wrong timestamps. Keep the math in the protected context
     and delegate only the static key switch to workqueue context.

   - remove a duplicate header include"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/headers: Remove duplicate #include <linux/sched/debug.h> line
  sched/clock: Fix broken stable to unstable transfer
  sched/clock, x86/perf: Fix "perf test tsc"
  sched/clock: Fix clear_sched_clock_stable() preempt wobbly

Pull EFI fix from Thomas Gleixner:
 "Downgrade the missing ESRT header printk to warning level and remove a
  useless error printk which just generates noise for no value"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/esrt: Cleanup bad memory map log messages

Pull timer fixes from Thomas Gleixner:
 "Two small fixes for the new CLKEVT_OF infrastructure"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  vmlinux.lds: Add __clkevt_of_table to kernel
  clockevents: Fix syntax error in clkevt-of macro

Pull irq fixes from Thomas Gleixner:
 "Two small fixlets:

   - select a required Kconfig to make the MVEBU driver compile

   - add the missing MIPS local GIC interrupts which prevent drivers to
     probe successfully"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/mips-gic: Fix Local compare interrupt
  irqchip/mvebu-odmi: Select GENERIC_MSI_IRQ_DOMAIN

Pull core fix from Thomas Gleixner:
 "Prevent leaking kernel memory via /proc/$pid/syscall when the queried
  task is not in a syscall"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  lib/syscall: Clear return values when no stack

Pull parisc fixes from Helge Deller:
 "Al Viro reported that - in case of read faults - our copy_from_user()
  implementation may claim to have copied more bytes than it actually
  did. In order to fix this bug and because of the way how gcc optimizes
  register usage for inline assembly in C code, we had to replace our
  pa_memcpy() function with a pure assembler implementation.

  While fixing the memcpy bug we noticed some other issues with our
  get_user() and put_user() functions, e.g. nested faults may return
  wrong data. This is now fixed by a common fixup handler for
  get_user/put_user in the exception handler which additionally makes
  generated code smaller and faster.

  The third patch is a trivial one-line fix for a patch which went in
  during 4.11-rc and which avoids stalled CPU warnings after power
  shutdown (for parisc machines which can't plug power off themselves).

  Due to the rewrite of pa_memcpy() into assembly this patch got bigger
  than what I wanted to have sent at this stage.

  Those patches have been running in production during the last few days
  on our debian build servers without any further issues"

* 'parisc-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Avoid stalled CPU warnings after system shutdown
  parisc: Clean up fixup routines for get_user()/put_user()
  parisc: Fix access fault handling in pa_memcpy()

Pull SCSI fixes from James Bottomley:
 "Thirteen small fixes: The hopefully final effort to get the lpfc nvme
  kconfig problems sorted, there's one important sg fix (user can induce
  read after end of buffer) and one minor enhancement (adding an extra
  PCI ID to qedi). The rest are a set of minor fixes, which mostly occur
  as user visible in error legs or on specific devices"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: remove the duplicated checking for supporting clkscaling
  scsi: lpfc: fix building without debugfs support
  scsi: lpfc: Fix PT2PT PRLI reject
  scsi: hpsa: fix volume offline state
  scsi: libsas: fix ata xfer length
  scsi: scsi_dh_alua: Warn if the first argument of alua_rtpg_queue() is NULL
  scsi: scsi_dh_alua: Ensure that alua_activate() calls the completion function
  scsi: scsi_dh_alua: Check scsi_device_get() return value
  scsi: sg: check length passed to SG_NEXT_CMD_LEN
  scsi: ufshcd-platform: remove the useless cast in ERR_PTR/IS_ERR
  scsi: qedi: Add PCI device-ID for QL41xxx adapters.
  scsi: aacraid: Fix potential null access
  scsi: qla2xxx: Fix crash in qla2xxx_eh_abort on bad ptr

Merge misc fixes from Andrew Morton:
 "11 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  kasan: do not sanitize kexec purgatory
  drivers/rapidio/devices/tsi721.c: make module parameter variable name unique
  mm/hugetlb.c: don't call region_abort if region_chg fails
  kasan: report only the first error by default
  hugetlbfs: initialize shared policy as part of inode allocation
  mm: fix section name for .data..ro_after_init
  mm, hugetlb: use pte_present() instead of pmd_present() in follow_huge_pmd()
  mm: workingset: fix premature shadow node shrinking with cgroups
  mm: rmap: fix huge file mmap accounting in the memcg stats
  mm: move mm_percpu_wq initialization earlier
  mm: migrate: fix remove_migration_pte() for ksm pages

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 4.11-rc5.

  The usual xhci fixes are here, as well as a fix for yet-another-bug-
  found-by-KASAN, those developers are doing great stuff here.

  And there's a phy build warning fix that showed up in 4.11-rc1.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: phy: isp1301: Fix build warning when CONFIG_OF is disabled
  xhci: Manually give back cancelled URB if we can't queue it for cancel
  xhci: Set URB actual length for stopped control transfers
  xhci: plat: Register shutdown for xhci_plat
  USB: fix linked-list corruption in rh_call_control()

Pull tty/serial fixes from Greg KH:
 "Here are some small fixes for some serial drivers and Kconfig help
  text for 4.11-rc5. Nothing major here at all, a few things resolving
  reported bugs in some random serial drivers.

  I don't think these made the last linux-next due to me getting to them
  yesterday, but I am not sure, they might have snuck in. The patches
  only affect drivers that the maintainers of sent me these patches for,
  so we should be safe here :)"

* tag 'tty-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: pl011: fix earlycon work-around for QDF2400 erratum 44
  serial: 8250_EXAR: fix duplicate Kconfig text and add missing help text
  tty/serial: atmel: fix TX path in atmel_console_write()
  tty/serial: atmel: fix race condition (TX+DMA)
  serial: mxs-auart: Fix baudrate calculation

Pull ACPI fixes from Rafael Wysocki:
 "These fix two issues related to IOAPIC hotplug, an overzealous build
  optimization that prevents the function graph tracer from working with
  the ACPI subsystem correctly and an RCU synchronization issue in the
  ACPI APEI code.

  Specifics:

   - drop the unconditional setting of the '-Os' gcc flag from the ACPI
     Makefile to make the function graph tracer work correctly with the
     ACPI subsystem (Josh Poimboeuf).

   - add missing synchronize_rcu() to ghes_remove() which removes an
     element from an RCU-protected list, but fails to synchronize it
     properly afterward (James Morse).

   - fix two problems related to IOAPIC hotplug, a local variable
     initialization in setup_res() and the creation of platform device
     objects for IO(x)APICs which are (a) unused and (b) leaked on
     hot-removal (Joerg Roedel)"

* tag 'acpi-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: Fix incompatibility with mcount-based function graph tracing
  ACPI / APEI: Add missing synchronize_rcu() on NOTIFY_SCI removal
  ACPI: Do not create a platform_device for IOAPIC/IOxAPIC
  ACPI: ioapic: Clear on-stack resource before using it

Pull power management fixes from Rafael Wysocki:
 "These fix a cpufreq core issue with the initialization of the cpufreq
  sysfs interface and a cpuidle powernv driver initialization issue.

  Specifics:

   - symbolic links from CPU directories to the corresponding cpufreq
     policy directories in sysfs are not created during initialization
     in some cases which confuses user space, so prevent that from
     happening (Rafael Wysocki).

   - the powernv cpuidle driver fails to pass a correct cpumaks to the
     cpuidle core in some cases which causes subsequent failures to
     occur, so fix it (Vaidyanathan Srinivasan)"

* tag 'pm-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: powernv: Pass correct drv->cpumask for registration
  cpufreq: Fix creation of symbolic links to policy directories

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes from I2C, specifically the I2C mux section. Thanks to
  peda for collecting them"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mux: pca954x: Add missing pca9546 definition to chip_desc
  Revert "i2c: mux: pca954x: Add ACPI support for pca954x"

Pull ARC fixes from Vineet Gupta:
 "Accumulated fixes for ARC which I've been been sitting on for a while:

   - reading clk from driver vs device tree [Vlad]

   - fix support for UIO in VDK platform [Alexey]

   - SLC busy bit reading workaround

   - build warning with kprobes header reorg"

* tag 'arc-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: fix build warnings with !CONFIG_KPROBES
  ARCv2: SLC: Make sure busy bit is set properly on SLC flushing
  ARC: vdk: Fix support of UIO
  ARCv2: make unimplemented vectors as no-ops rather than halt core
  ARC: get rate from clk driver instead of reading device tree
  ARC: [dts] add cpu nodes to ARCHS SMP device tree
  ARC: [dts] add input clocks for cpu nodes

Pull nfsd fixes from Bruce Fields:
 "The restriction of NFSv4 to TCP went overboard and also broke the
  backchannel; fix.

  Also some minor refinements to the nfsd version-setting interface that
  we'd like to get fixed before release"

* tag 'nfsd-4.11-1' of git://linux-nfs.org/~bfields/linux:
  svcrdma: set XPT_CONG_CTRL flag for bc xprt
  NFSD: fix nfsd_reset_versions for NFSv4.
  NFSD: fix nfsd_minorversion(.., NFSD_AVAIL)
  NFSD: further refinement of content of /proc/fs/nfsd/versions
  nfsd: map the ENOKEY to nfserr_perm for avoiding warning
  SUNRPC/backchanel: set XPT_CONG_CTRL flag for bc xprt

The work-around for the Qualcomm Datacenter Technologies QDF2400
erratum 44 sets the "qdf2400_e44_present" global variable if the
work-around is needed.  However, this check does not happen until after
earlycon is initialized, which means the work-around is not
used, and the console hangs as soon as it displays one character.

Fixes: d8a4995b ("tty: pl011: Work around QDF2400 E44 stuck BUSY bit")
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull btrfs fixes from Chris Mason:
 "We have three small fixes queued up in my for-linus-4.11 branch"

* 'for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix an integer overflow check
  btrfs: Change qgroup_meta_rsv to 64bit
  Btrfs: bring back repair during read

Fixes this:

  kexec: Undefined symbol: __asan_load8_noabort
  kexec-bzImage64: Loading purgatory failed

Link: http://lkml.kernel.org/r/1489672155.4458.7.camel@gmx.deSigned-off-by: Mike Galbraith <efault@gmx.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kbuild test robot reported a non-static variable name collision between
a staging driver and a RapidIO driver, with a generic variable name of
'dbg_level'.

Both drivers should be changed so that they don't use this generic
public variable name.  This patch fixes the RapidIO driver but does not
change the user interface (name) for the module parameter.

  drivers/staging/built-in.o:(.bss+0x109d0): multiple definition of `dbg_level'
  drivers/rapidio/built-in.o:(.bss+0x16c): first defined here

Link: http://lkml.kernel.org/r/ab527fc5-aa3c-4b07-5d48-eef5de703192@infradead.orgSigned-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Changes to hugetlbfs reservation maps is a two step process.  The first
step is a call to region_chg to determine what needs to be changed, and
prepare that change.  This should be followed by a call to call to
region_add to commit the change, or region_abort to abort the change.

The error path in hugetlb_reserve_pages called region_abort after a
failed call to region_chg.  As a result, the adds_in_progress counter in
the reservation map is off by 1.  This is caught by a VM_BUG_ON in
resv_map_release when the reservation map is freed.

syzkaller fuzzer (when using an injected kmalloc failure) found this
bug, that resulted in the following:

 kernel BUG at mm/hugetlb.c:742!
 Call Trace:
  hugetlbfs_evict_inode+0x7b/0xa0 fs/hugetlbfs/inode.c:493
  evict+0x481/0x920 fs/inode.c:553
  iput_final fs/inode.c:1515 [inline]
  iput+0x62b/0xa20 fs/inode.c:1542
  hugetlb_file_setup+0x593/0x9f0 fs/hugetlbfs/inode.c:1306
  newseg+0x422/0xd30 ipc/shm.c:575
  ipcget_new ipc/util.c:285 [inline]
  ipcget+0x21e/0x580 ipc/util.c:639
  SYSC_shmget ipc/shm.c:673 [inline]
  SyS_shmget+0x158/0x230 ipc/shm.c:657
  entry_SYSCALL_64_fastpath+0x1f/0xc2
 RIP: resv_map_release+0x265/0x330 mm/hugetlb.c:742

Link: http://lkml.kernel.org/r/1490821682-23228-1-git-send-email-mike.kravetz@oracle.comSigned-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>