Define some related TDLS protocol constants and advertise channel switch
support in the extended-capabilities IE when the feature bit is defined.

Actually supporting TDLS channel-switching also requires support for
some new nl80211 commands, to be introduced by future patches.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add the BSS coex IE in case we support HT40 channels, as mandated by
section 8.5.13 in IEEE802.11 2012.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This information element is mandatory in case TDLS channel-switching is to
be supported. The channels given are ones supported and allowed to be
active in the current regulatory setting.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For some TDLS channel switch implementations data frames need to be
sent by the firmware based on a template. This template should be
created by mac80211, and thus needs to properly be built from an
802.3 frame into an 802.11 frame. In addition, the device will need
the key information so the select_key handler needs to be run.
However, the driver/device will be responsible for all of the crypto
encapsulation, as the sequence numbers etc. cannot be built by the
host anyway in this case since it's a template to be used multiple
times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Factor out the 802.11 header building code from the xmit function
to be able to use it separately in a later commit.

While at it, fix up some documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of passing the band as a parameter to ieee80211_xmit()
and ieee80211_tx(), move it outside of the two functions while
making sure info->band is set up before calling them.

This removes the parameter and simplifies the follow commit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since the TDLS peer station might not receive the teardown
packet (e.g., when in PS), this makes sure the packet is
retransmitted - this time through the AP - if the TDLS peer
didn't ACK the packet.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Allows setting of an skb's flags - if needed - when calling
ieee80211_subif_start_xmit().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This brings in some mwifiex changes that further patches will
need to work on top to not cause merge conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently, when a roc period expires, the offchannel
timer calls ieee80211_remain_on_channel_expired(), but
the roc state is cleared only when the queued work
to switch to the operating channel gets a chance to run.

This race is a problem because mac80211 can issue a
new roc request in this window. To avoid this, handle
roc completion in the offchannel timer itself.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In a GO/STA setup, when we switch to the STA context,
the channel context timer is scheduled with a period of
half the beacon interval. If a beacon is received in
this duration, the timer is adjusted to accommodate
TSF sync done by the HW.

But, if the actual channel switch is delayed for some
reason, we end up rearming the timer every time a new
beacon is received. Avoid this by doing the adjustment
only once.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If for some reason a beacon with a new NoA is
not sent out, then reset the mgd_prepare_tx flag.
Not doing this will result in a situation where
a GO will send a new NoA when it shouldn't.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch makes sure that pending roc/scan
operations are cancelled properly when a new
context is assigned/unassigned.

The flush_work() call to flush out any scheduled
channel context work is removed, instead, sc->mutex
is dropped to allow any pending work to get a chance
to complete by the channel scheduler. Also, increase
the timeout to allow a switch to an active GO.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When a pending roc or scan operation is cancelled,
the offchannel operation is cleared, but the offchannel
state in the main scheduler is not cleared. This causes
problems since an active GO will try to process a stale
offchannel request that was deferred earlier. Fix this
by clearing the state when there is no pending offchannel
(roc/scan) operation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The registers that control the on-chip thermometer
need to be programmed based on the chainmask that
the solution supports, not the chainmask that is
present in the eeprom.

Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cc: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The base TSF is used for HW timers 0..7, but chips
in the AR9003 family and above can support more generic
timers. To use them, however, a second HW TSF needs to
be enabled. This patch allows usage of the extra
timers by starting the second TSF properly.

The extra set of HW timers is apparently also present
in AR9287, but we enable it only for the AR9003 family.

Cc: Kobi Cohen-Arazi <kobic@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On some x86 platforms, the LED gpio is active high
instead of active low. Identify such cards and modify
the GPIO usage to make sure LED works properly.

Cc: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch updates the initvals for QCA953x v1.1 and v2.0
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Duplicates have been marked.
* New initvals for 1.1 and 2.0 versions.
* xPA support.
* Fix for low power issue.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In secured mesh, the unicast mgmt frame is encrypted using
the same key that used for encrypting the unicast data frame.
This patch "ath9k_htc_firmware: fix the offset of CCMP header
for mesh data frame" applied to open-ath9k-htc-firmware allows
the ath9k_htc to be loaded without "nohwcrypt=1". Unfortunately,
this is not working and we still need CCMP encryption of
transmitted management frames to be done in software.

So this patch allows the software encryption for transmitted
management frame to be done in software but remain the hardware
decryption for received management frame.

This patch is tested with the following hardwares:
- TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287]
- AR9271 802.11n

and managed to work with peer mesh STA equipped with ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the sw_mgmt_crypto_tx flag to trigger the CCMP encryption
for transmitted management frames to be done in software while
the sw_mgmt_crypto_rx flag is used to trigger the CCMP decryption
for received management frames to be done in software.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Auto TDLS support is enabled per device. As of now add this
feature only for SD8887.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for parsing TDLS discovery
frames. After parsing, we update peer RSSI information.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds auto TDLS support to mwifiex.

Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds WMM support for TDLS link. Patch
add WMM info IE for TDLS setup request/response frames
while WMM parameter for TDLS confirm frame.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When Teardown event from FW is indicated to userspace, userspace
would trigger tdls_oper handler to disable TDLS link.
We need not do this explicitly here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

RX packet descriptor structure has recently changed in FW.
This patch updates rxpd accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We need to assign the hw queues for mesh interface. Otherwise,
we are not able to bring up the mesh interface due to the
IEEE80211_INVAL_HW_QUEUE error.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

we can have here two variants. Add
ATH9K_CMN_DEBUGFS y if ATH9K_CMN_DEBUGFS || ATH9K_HTC_DEBUGFS
wich will add more configurations and testcases. Or remove ATH9K_HTC_DEBUGFS
which need more time to be done.

So, make common-spectral ignore ATH9K_DEBUGFS option for now.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/htc_drv_init.c:56:6: sparse: symbol 'ath9k_htc_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:61:6: sparse: symbol 'ath9k_htc_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/htc_drv_init.c:66:19: sparse: symbol 'ath9k_htc_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/init.c:91:6: sparse: symbol 'ath9k_op_ps_wakeup' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:96:6: sparse: symbol 'ath9k_op_ps_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/init.c:101:19: sparse: symbol 'ath9k_ps_ops' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds module load parameter driver_mode for mwifiex
which would enable driver to create AP or P2P client interface while loading
module. driver_mode is bitmap of interface modes for station, AP and
P2P client.

Station interface is created by default and is unaffected by driver_mode
parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When channel-context is not enabled, all vifs belong to
the first context, but it is not configured as 'assigned'.

Fix misc debugfs file to print out info for non-assigned
contexts, and also print whether ctx is assigned or not.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Kalle Valo <kvalo@qca.qualcomm.com> says:

"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:

o fix resume (Bartosz)

o firmware restart is now faster and more reliable (Michal)

o it's now possible to test hardware restart functionality without
  crashing the firmware using hw-restart parameter with
  simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix to use v10.2 wmi call for firmware v10.2.
It turned out that peer association function was using
v10.1 wmi call for v10.2 firmware during code review.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This will enable AP mode to change channel width dynamically
based on 20/40 intolerance report sent by associated client.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch would help bring up wifi interface with default board
data in case of failures in otp download. It is useful for initial
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

For packet log, the transmitted frame 802.11 header alone is sufficient.
Recording entire packet is also consuming lot of disk space. To optimize
this, tx and rx data tracepoints are splitted into header and payload
tracepoints.

To record tx ieee80211 headers

     trace-cmd record -e ath10k_tx_hdr

To record complete packets

     trace-cmd record -e ath10k_tx_hdr -e ath10k_tx_payload

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>