So far, Realtek codec driver evaluates the NIDs for volume and mute
controls twice, once while parsing the DACs and evaluating the
assignment, and another while creating the mixer elements.  This is
utterly redundant and even fragile, as it's assuming that the ctl
element evaluation is identical between both parsing DACs and creating
mixer elements.

This patch simplifies the code flow by doing the volume / mute
controls evaluation only once while parsing the DACs.  The patch ended
up in larger changes than expected because of some cleanups became
mandatory.

As a gratis bonus, this patch also fixes some cases where the stereo
channels are used wrongly for mono amps.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The mono widget is always connected to the left channel, thus the left
channel amp value also should be referred for mono widgets instead of
the right channel.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

As we parse the output paths more precisely now, we can use this path
list for parsing the widgets for volume and mute mixer controls.
The spec->vol_ctls[] and sw_ctls[] bitmasks are replaced with the
ctls[] in each output path instance.

Interestingly, this move alone automagically fixes some bugs that the
conflicting volume or mute NIDs weren't properly detected.
Also, by parsing the whole path, there are more chances to get a free
widget for volume/mute controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add the output path parser to Realtek codec driver as we already have
in patch_via.c.  The nid_path struct represents the complete output
path from a DAC to a pin.  The alc_spec contains an array of these
paths, and a new path is added at each time when a new DAC is
assigned.

So far, this path list is used only in limited codes: namely in this
patch, only alc_is_dac_already_used() checks the list instead of dac
arrays in all possible outputs.  In the later development, the path
list will be referred from more places, such as the mixer control
assignment / check, the mute/unmute of active routes, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In the probing phase, create a list of all available DACs in the codec
and use it for checking the single DAC connections.
This list will be used in more other places in the later commits, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Use the helper function snd_hda_get_conn_index() instead of open
codes.  This also improves the detection of some routes to DAC on
ALC260 (although the difference doesn't influence on the end
results of the mapping).
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added the support for a new codec ALC284, which is compatible with
ALC269.  Also add more codec variants to handle the SSID check
properly.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Fixes the following sparse warning:
sound/usb/mixer_quirks.c:1209:23: warning:
symbol 'ebox44_table' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Use correct bitmask for AES32 cards to determine wordclock lock state,
add missing bitmask for sync check and make output of the corresponding
control and /proc coherent.
Signed-off-by: Andre Schramm <andre.schramm@iosono-sound.com>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This reverts commit 697c373e.

The original patch was meant to remove clicking, but in fact caused even
more clicking instead.

Thanks to c4pp4 for doing most of the work with this bug.

BugLink: https://bugs.launchpad.net/bugs/886975Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We've got a few bug reports that the runtime D3 results in the dead
HD-audio controller.  It seems that the problem is in a deeper level
than the sound driver itself, so as a temporal solution, disable the
feature for these controllers again.
Reported-and-tested-by: Vincent Blut <vincent.debian@free.fr>
Reported-and-tested-by: Maurizio Avogadro <mavoga@gmail.com>
Cc: <stable@vger.kernel.org> [v3.7]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The mute LED is in this case connected to the Mic1 VREF.

The machine also exposes the following string in BIOS:
"HP_Mute_LED_0_A", so if more machines are coming, it probably
makes sense to try to do something more generic, like for the
IDT codec.

Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1096789Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

vortex_wt_setdsout performs bit-negation on the bit position (wt&0x1f)
rather than on the resulting bitmask.  This code is never actually
invoked (vortex_wt_setdsout is always called with en=1), so this does
not currently cause any problem, and this patch is simply cleanup.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added a fix for hardware dependence bug where a sound card failure
should not result in reading beyond array memory index.
Signed-off-by: Asim Kadav <kadav@cs.wisc.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch is based on 3.8-rc1. It fixes two things:
1) A kernel panic caused by incorrect allocation of a u8 variable
   "bootresponse".
2) A noisy dmesg (urb status -32) caused by broken pipe to an
   invalid midi endpoint.

It is also a little cleaner because there is no need for a new
QUIRK_MIDI type as suggested by kernel developers, since the device
follows exactly the MIDIMAN protocol.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Support the Creative BT-D1 Bluetooth USB audio device. Before this
patch, Linux had trouble finding the correct USB descriptors and bailed
out with these messages:

 no or invalid class specific endpoint descriptor

Now it still prints these messages on hotplug:

 snd-usb-audio: probe of ...:1.0 failed with error -5
 snd-usb-audio: probe of ...:1.2 failed with error -5
 snd-usb-audio: probe of ...:1.3 failed with error -5

But the device works correctly, including the HID support.

The patch is diff'ed against 3.8-rc1 but should apply to older kernels
as well.
Signed-off-by: Alexander Schremmer <alex@alexanderweb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The vmaster hook sends 1 for enabled/unmuted and 0 for disabled/muted,
but "Mute-LED Mode" being "On" refers to the LED being on, not the
volume being on.
Therefore "On" and "Off" should be switched.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull watchdog updates from Wim Van Sebroeck:
 "This includes some fixes and code improvements (like
  clk_prepare_enable and clk_disable_unprepare), conversion from the
  omap_wdt and twl4030_wdt drivers to the watchdog framework, addition
  of the SB8x0 chipset support and the DA9055 Watchdog driver and some
  OF support for the davinci_wdt driver."

* git://www.linux-watchdog.org/linux-watchdog: (22 commits)
  watchdog: mei: avoid oops in watchdog unregister code path
  watchdog: Orion: Fix possible null-deference in orion_wdt_probe
  watchdog: sp5100_tco: Add SB8x0 chipset support
  watchdog: davinci_wdt: add OF support
  watchdog: da9052: Fix invalid free of devm_ allocated data
  watchdog: twl4030_wdt: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
  watchdog: remove depends on CONFIG_EXPERIMENTAL
  watchdog: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
  watchdog: DA9055 Watchdog driver
  watchdog: omap_wdt: eliminate goto
  watchdog: omap_wdt: delete redundant platform_set_drvdata() calls
  watchdog: omap_wdt: convert to devm_ functions
  watchdog: omap_wdt: convert to new watchdog core
  watchdog: WatchDog Timer Driver Core: fix comment
  watchdog: s3c2410_wdt: use clk_prepare_enable and clk_disable_unprepare
  watchdog: imx2_wdt: Select the driver via ARCH_MXC
  watchdog: cpu5wdt.c: add missing del_timer call
  watchdog: hpwdt.c: Increase version string
  watchdog: Convert twl4030_wdt to watchdog core
  davinci_wdt: preparation for switch to common clock framework
  ...

Pull CIFS fixes from Steve French:
 "Misc small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: eliminate cifsERROR variable
  cifs: don't compare uniqueids in cifs_prime_dcache unless server inode numbers are in use
  cifs: fix double-free of "string" in cifs_parse_mount_options

Pull dm update from Alasdair G Kergon:
 "Miscellaneous device-mapper fixes, cleanups and performance
  improvements.

  Of particular note:
   - Disable broken WRITE SAME support in all targets except linear and
     striped.  Use it when kcopyd is zeroing blocks.
   - Remove several mempools from targets by moving the data into the
     bio's new front_pad area(which dm calls 'per_bio_data').
   - Fix a race in thin provisioning if discards are misused.
   - Prevent userspace from interfering with the ioctl parameters and
     use kmalloc for the data buffer if it's small instead of vmalloc.
   - Throttle some annoying error messages when I/O fails."

* tag 'dm-3.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (36 commits)
  dm stripe: add WRITE SAME support
  dm: remove map_info
  dm snapshot: do not use map_context
  dm thin: dont use map_context
  dm raid1: dont use map_context
  dm flakey: dont use map_context
  dm raid1: rename read_record to bio_record
  dm: move target request nr to dm_target_io
  dm snapshot: use per_bio_data
  dm verity: use per_bio_data
  dm raid1: use per_bio_data
  dm: introduce per_bio_data
  dm kcopyd: add WRITE SAME support to dm_kcopyd_zero
  dm linear: add WRITE SAME support
  dm: add WRITE SAME support
  dm: prepare to support WRITE SAME
  dm ioctl: use kmalloc if possible
  dm ioctl: remove PF_MEMALLOC
  dm persistent data: improve improve space map block alloc failure message
  dm thin: use DMERR_LIMIT for errors
  ...

This reverts commit 79f77bf9.

This is obviously wrong, and I have no idea how I missed seeing the
warning in testing: I must just not have looked at the right logs.  The
caller bumps rq_resused/rq_next_page, so it will always be hit on a
large enough read.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more infiniband changes from Roland Dreier:
 "Second batch of InfiniBand/RDMA changes for 3.8:
   - cxgb4 changes to fix lookup engine hash collisions
   - mlx4 changes to make flow steering usable
   - fix to IPoIB to avoid pinning dst reference for too long"

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/cxgb4: Fix bug for active and passive LE hash collision path
  RDMA/cxgb4: Fix LE hash collision bug for passive open connection
  RDMA/cxgb4: Fix LE hash collision bug for active open connection
  mlx4_core: Allow choosing flow steering mode
  mlx4_core: Adjustments to Flow Steering activation logic for SR-IOV
  mlx4_core: Fix error flow in the flow steering wrapper
  mlx4_core: Add QPN enforcement for flow steering rules set by VFs
  cxgb4: Add LE hash collision bug fix path in LLD driver
  cxgb4: Add T4 filter support
  IPoIB: Call skb_dst_drop() once skb is enqueued for sending

Pull asm-generic cleanup from Arnd Bergmann:
 "These are a few cleanups for asm-generic:

   - a set of patches from Lars-Peter Clausen to generalize asm/mmu.h
     and use it in the architectures that don't need any special
     handling.
   - A patch from Will Deacon to remove the {read,write}s{b,w,l} as
     discussed during the arm64 review
   - A patch from James Hogan that helps with the meta architecture
     series."

* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  xtensa: Use generic asm/mmu.h for nommu
  h8300: Use generic asm/mmu.h
  c6x: Use generic asm/mmu.h
  asm-generic/mmu.h: Add support for FDPIC
  asm-generic/mmu.h: Remove unused vmlist field from mm_context_t
  asm-generic: io: remove {read,write} string functions
  asm-generic/io.h: remove asm/cacheflush.h include

Commit db5b0ae0 ("Merge tag 'dt' of git://git.kernel.org/.../arm-soc")
causes a duplicated build target.  This patch fixes it and sorts out the
build target alphabetically so that we can recognize something wrong
easily.

Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Rename stripe_map_discard to stripe_map_range and reuse it for WRITE
SAME bio processing.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

This patch removes map_info from bio-based device mapper targets.
map_info is still used for request-based targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Eliminate struct map_info from dm-snap.

map_info->ptr was used in dm-snap to indicate if the bio was tracked.
If map_info->ptr was non-NULL, the bio was linked in tracked_chunk_hash.

This patch removes the use of map_info->ptr. We determine if the bio was
tracked based on hlist_unhashed(&c->node). If hlist_unhashed is true,
the bio is not tracked, if it is false, the bio is tracked.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

This patch removes endio_hook_pool from dm-thin and uses per-bio data instead.

This patch removes any use of map_info in preparation for the next patch
that removes map_info from bio-based device mapper.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Don't use map_info any more in dm-raid1.

map_info was used for writes to hold the region number. For this purpose
we add a new field dm_bio_details to dm_raid1_bio_record.

map_info was used for reads to hold a pointer to dm_raid1_bio_record (if
the pointer was non-NULL, bio details were saved; if the pointer was
NULL, bio details were not saved). We use
dm_raid1_bio_record.details->bi_bdev for this purpose. If bi_bdev is
NULL, details were not saved, if bi_bdev is non-NULL, details were
saved.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Replace map_info with a per-bio structure "struct per_bio_data" in dm-flakey.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Rename struct read_record to bio_record in dm-raid1.

In the following patch, the structure will be used for both read and
write bios, so rename it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

This patch moves target_request_nr from map_info to dm_target_io and
makes it accessible with dm_bio_get_target_request_nr.

This patch is a preparation for the next patch that removes map_info.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Replace tracked_chunk_pool with per_bio_data in dm-snap.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Replace io_mempool with per_bio_data in dm-verity.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Replace read_record_pool with per_bio_data in dm-raid1.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Introduce a field per_bio_data_size in struct dm_target.

Targets can set this field in the constructor. If a target sets this
field to a non-zero value, "per_bio_data_size" bytes of auxiliary data
are allocated for each bio submitted to the target. These data can be
used for any purpose by the target and help us improve performance by
removing some per-target mempools.

Per-bio data is accessed with dm_per_bio_data. The
argument data_size must be the same as the value per_bio_data_size in
dm_target.

If the target has a pointer to per_bio_data, it can get a pointer to
the bio with dm_bio_from_per_bio_data() function (data_size must be the
same as the value passed to dm_per_bio_data).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Add WRITE SAME support to dm-io and make it accessible to
dm_kcopyd_zero().  dm_kcopyd_zero() provides an asynchronous interface
whereas the blkdev_issue_write_same() interface is synchronous.

WRITE SAME is a SCSI command that can be leveraged for more efficient
zeroing of a specified logical extent of a device which supports it.
Only a single zeroed logical block is transfered to the target for each
WRITE SAME and the target then writes that same block across the
specified extent.

The dm thin target uses this.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

The linear target can already support WRITE SAME requests so signal
this by setting num_write_same_requests to 1.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

WRITE SAME bios have a payload that contain a single page.  When
cloning WRITE SAME bios DM has no need to modify the bi_io_vec
attributes (and doing so would be detrimental).  DM need only alter the
start and end of the WRITE SAME bio accordingly.

Rather than duplicate __clone_and_map_discard, factor out a common
function that is also used by __clone_and_map_write_same.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>