This patch fixes several shortcomings of the
previous implementation. Features of the
rewrite include:

 * handles undocumented "0x0000" word at the
   start of the frequency table.
   (Affected some early? DELL 1450 USB devices
    and my Symbol 5GHz miniPCI card.)

 * supports more than just one reference point
   per band. (Also needed for the Symbol card.)

 * ships with default values in case the eeprom
   data is damaged, absent or unsupported.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some channel indices of the low 5GHz band clash with
those of the 2.4GHz band. Therefore we should go
with the channel's center frequency.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Case assert is violated should be quite unlikely.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.

Make asynchronous zd_usb_iowrite16v_async available outside zd_usb.c
and use where possible.

This lower CPU usage from ~10% to ~2% on Intel Atom when running
AP-mode with 100 TU beacon interval.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.

This patch makes zd_usb_iowrite16v use asynchronous urb submit within
zd_usb.c. zd_usb_iowrite16v_async_start is used to initiate writing
multiple commands to device using zd_usb_iowrite16v_async. Each URB
is delayed and submitted to device by next zd_usb_iowrite16v_async
call or by call to zd_usb_iowrite16v_async_end. URBs submitted by
zd_usb_iowrite16v_async have URB_NO_INTERRUPT set and last URB
send by zd_usb_iowrite16v_async_end does not. This lower CPU
usage when doing writes that require multiple URBs.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw is using usb_bulk_msg() with usb_sndbulkpipe() on interrupt endpoint.
However usb_bulk_msg() internally corrects this and makes interrupt URB.

It's better to change usb_bulk_msgs in zd1211rw to usb_interrupt_msg for less
confusion.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211_rx_h_check returned RX_DROP_MONITOR in case the if statement
in question was true but the same return value is also used directly
after the if clause. Hence, we can just drop the whole if clause and as
such simplify the code.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Beaconing should be disabled before stopping beacon queue.
Not doing so could queue up beacons in hw that causes
failure to stop Tx DMA, due to pending frames in hw
and also unnecessary beacon tasklet schedule.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 739fd940 ("rt2x00: Pad beacon to multiple of 32 bits")
added calls to skb_pad() without checking the return value,
which could cause problems if any of those calls does happen
to fail. Add checks to prevent this from happening.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make the phy.c codes for rtl8192ce and rtl8192cu be as alike as possible.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make rtlwifi/rtl8192ce/fw.{h,c} match what will be needed for
rtlwifi/rtl8192cu.{h,c}.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To reuse as much code as possible when adding additional drivers to the
rtlwifi tree, the common parts of various routines are moved to
drivers/net/wireless/rtlwifi. This patch does that for the version of
dm.{h,c} used by rtl8192ce.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The rtlwifi core needs some changes before inclusion of a driver
for the RTL8192CU USB device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: <chaoming_li@realsil.com.cn>
Signed-off-by: <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For 2000 series, need to handle bt traffic changes when
receive notification from uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

If bt coex is disabled, do not process any bt related information
from uCode even received.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Combo devices have TX statistics on different place, because
struct statistics_rx_bt and struct statistics_rx have different
size. User proper values on combo devices instead of random data.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make ack health code easies to read. Compared to previous
code, we do not print debug messages when expected_ack_cnt_delta == 0
and also do check against negative deltas.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No functional change, make recover from statistics code
easies to read.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The variable appears in both ath_softc and ath_beacon_config.
The struct ath_beacon_config is embedded in ath_softc. The redundant
variable was added by commit id 57c4d7b4.
Signed-off-by: Steve Brown <sbrown@cortland.com>
Reviewed-by: Mohammed Shafi <shafi.ath9k@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

My previous patch to optimize scanning on operating channel
accidentally removed the code that would ensure power was
set to maximum for scanning.

This patch re-adds that functionality.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Narrow channel types can function within larger channel types.
So, use existing channel type for work items when possible.
This decreases hardware channel changes significantly when
using non NO_HT channel types on the operating channel.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previous code set the channel type to NO_HT, but it
appears that NO_HT packets can be sent on any channel
type, so we do not need to change the channel type
as long as the channel is correct.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some were indirectly set to NO_HT (zero), but I think
it's better to explicitly set it in case the enum ever
changes.  In cfg.c, it seems the channel-type was just
ignored (and thus always set to NO_HT).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of looking for supported_rates change on every tx packet,
just extract the supported_rates after association completes (station only).

Remove wl1271.sta_rate_set and WL1271_FLAG_STA_RATES_CHANGED which are
not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

make the configuration management more flexible by using the
conf struct, rather than predefined macros.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

This patch adds support for the new wl12xx firmware (Rev 6.1.3.50.49)

Since this fw is not backward compatible with previous fw versions,
a new fw (with different name) is being fetched.

(the patch is big because it contains all the required fw api changes.
splitting it into multiple patches will result in corrupted intermediate
commits)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

mcp2.5 uses this acx to configure the fw only once, rather than
passing the params in every enter psm command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Change hcid to bluetoothd.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Also moves some L2CAP sending functions declaration to l2cap.h
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Declare __l2cap_wait_ack() and  l2cap_sock_clear_timer() in l2cap.h
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

It causes the move of the declaration of 3 functions to l2cap.h:
l2cap_get_ident(), l2cap_send_cmd(), l2cap_build_conf_req()
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>