- 26 Jul, 2010 40 commits
-
-
Eric Bénard authored
Signed-off-by:
Eric Bénard <eric@eukrea.com> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
Eric Bénard authored
DEBUG_LL is actually broken on i.MX25, this patch fix it. Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Jason Wang authored
Add keymaps and imx_keypad device registration for imx51_3ds board. Signed-off-by:
Jason Wang <jason77.wang@gmail.com> Signed-off-by:
-
Jason Wang authored
add imx_keypad platform device definition and clocks for mx51 platforms. Signed-off-by:
-
Jason Wang authored
3-stack is a reference board from Freescale for their i.MX51 SoC. Add board definition, Kconfig and Makefile to enable Freescale 3-stack board. Boot tested on a i.MX51 3-stack Rev2.0 board Signed-off-by:
-
Rogerio Pimentel authored
mx27_3ds: add support for the keypad Signed-off-by:
Rogerio Pimentel <rogerio.pimentel@freescale.com> Signed-off-by:
-
Jason Wang authored
Because we add a 3ds debug board support in mxc level, we remove those redundant codes from board level. Signed-off-by:
-
Jason Wang authored
The debug board is little different for all mxc 3-stack(PDK) platforms, it is possible here to add a common implementation to support this board. Signed-off-by:
-
git://git.pengutronix.de/git/ukl/linux-2.6Uwe Kleine-König authored
There are some more conflicts than detected by git, namely support for the newly added cpuimx machines needed to be converted to dynamic device registration. Signed-off-by:Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Conflicts: arch/arm/mach-imx/Makefile arch/arm/mach-imx/devices.c arch/arm/mach-imx/devices.h arch/arm/mach-imx/eukrea_mbimx27-baseboard.c arch/arm/mach-mx2/Kconfig arch/arm/mach-mx25/Makefile arch/arm/mach-mx25/devices.c arch/arm/plat-mxc/include/mach/mx25.h arch/arm/plat-mxc/include/mach/mxc_nand.h
-
Baruch Siach authored
Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Luotao Fu authored
cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding pin multiplexing either into the initial pin config table or ifdef blocks. Signed-off-by:
Luotao Fu <l.fu@pengutronix.de> Signed-off-by:
-
Luotao Fu authored
this one adds the frambuffer device and a TFT panel to the PhyCard-S (pca100) board. Signed-off-by:
-
Jason Wang authored
These GPIO bank offsets are useful when define a gpio number. E.G. when GPIO PORTC pin 6 is used for irq request pin of external expanding device, we can define it like: #define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6) Signed-off-by:
-
Jason Wang authored
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board, add GPIO_1_6 definiton because this pin is used as a CPLD parent irq request pin on imx51_3ds board. Signed-off-by:
-
Jason Wang authored
For pad EIM_D27 to work in UART3_RTS mode, the input path should be 3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux value should be 2 instead of 8. Signed-off-by:
-
Amit Kucheria authored
The pads capable of being used as GPIOs had their pad-name and mode-name switched. Also, fix the following: - Whitespace fixes - Replace IOMUX_CONFIG_ALTn with 'n' Signed-off-by:
Amit Kucheria <amit.kucheria@canonical.com> Signed-off-by:
-
Eric Bénard authored
* cpuimx35 integrates i.MX35, RAM, NAND, Ethernet, I2C RTC, USB Host, USB OTG and I2C touchscreen controller * mbimxsd provides access to LCD, Audio, LED, Switch button, UART ... Signed-off-by:
-
Baruch Siach authored
The information in the i.MX25 Reference Manual is lacking. Add information from the Freescale BSP. Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Eric Bénard authored
* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host and USB OTG * mbimxsd provides access to LCD, Audio, LED, Switch button, UART ... Signed-off-by:
-
Eric Bénard authored
* add clocks for audmux and ssi 1 & 2 * add irq for ssi 1 & 2 * add devices platform for ssi1 & 2 * update audmux-v2 for i.MX25 * add base addresses for audmux & ssi 1 & 2 * add iomux configuration for GPIO for AUD5 port Signed-off-by:
-
Eric Bénard authored
i.MX25's udc port is the same as i.MX35's one Signed-off-by:
-
Eric Bénard authored
i.MX25's EHCI is the same as i.MX35's one. Signed-off-by:
-
Eric Bénard authored
usb drivers need to get the right value for otg clock so calculate and return it Signed-off-by:
-
Eric Bénard authored
i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse most of the i.MX35's defines. Signed-off-by:
-
Eric Bénard authored
the standard place for this define is include/mach/mx25.h Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
when CONFIG_USB_ULPI is not defined we actually get : warning: 'otg_pdata' defined but not used warning: 'usbh2_pdata' defined but not used Signed-off-by:
-
Eric Bénard authored
without this patch, ipu_clk's value is 0 thus preventing mx3fb from calculating the right divisor for pixel clock generator. Signed-off-by:
-
Dinh Nguyen authored
Add device registration and setup IOMUX pins in the mx51_babbage board feil. Signed-off-by:
Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by:
-
Dinh Nguyen authored
This patch adds I2C functionality to the Freescale MX51 Babbage HW. The patch adds device structures, i2c board slave device defines, IOMUX pin defines, and clocks. Signed-off-by:
-
Amit Kucheria authored
This patch fixes the clock refcounting when reparenting is used. Boot-tested on imx51 babbage board. Sascha pointed out a good explanation of refcounting here: http://www.spinics.net/lists/arm-kernel/msg85879.htmlSigned-off-by:
-
Baruch Siach authored
The keymap is taken from the Freescale supplied kernel. Signed-off-by:
-
