- 27 Sep, 2018 20 commits
-
-
Chen-Yu Tsai authored
This panel is marketed as Banana Pi 7" LCD display. On the back is a sticker denoting the model name S070WV20-CT16. This is a 7" 800x480 panel connected through a 24-bit RGB interface. However the panel only does 262k colors. Depending on the variant, the PCB attached to the panel module either supports DSI, or DSI + 24-bit RGB. DSI is converted to 24-bit RGB via an onboard ICN6211 MIPI DSI - RGB bridge chip, then fed to the panel itself. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Thierry Reding <treding@nvidia.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-5-wens@csie.org
-
Heiko Stuebner authored
There is no need to check innolux->base.dev when trying to remove the panel, as that variable is always set directly before the panel gets added and will still be available on panel_remove. Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Giulio Benetti authored
Add documentation for S043WQ26H-CT7 panel Signed-off-by:
Giulio Benetti <giulio.benetti@micronovasrl.com> Reviewed-by:
-
Giulio Benetti authored
This patch adds support for CDTech S043WQ26H-CT7 480x272 4.3" panel to DRM simple panel driver. Signed-off-by:
-
Giulio Benetti authored
Add documentation for S070WV95-CT16 panel Signed-off-by:
-
Giulio Benetti authored
This patch adds support for CDTech S070WV95-CT16 800x480 7" panel to DRM simple panel driver. Signed-off-by:
-
Giulio Benetti authored
This adds a vendor prefix "cdtech" for CDTech(H.K.) Electronics Limited Website: www.cdtech-lcd.com Signed-off-by:
-
Fabio Estevam authored
There is a missing ">" character in Marco's email. Fix it. Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
-
Fabio Estevam authored
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by:
-
Andrzej Hajda authored
Panel timings were taken from vendor code and are not fully correct - refresh rate is about 50Hz instead of 60Hz. The patch fixes it. Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Signed-off-by:
-
Hans de Goede authored
GPD has done it again, make a nice device (good), use way too generic DMI strings (bad) and use a portrait screen rotated 90 degrees (ugly). Because of the too generic DMI strings this entry is also doing bios-date matching, so the gpd_win2 data struct may very well need to be updated with some extra bios-dates in the future. Reported-and-tested-by: russianneuromancer@ya.ru Acked-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180909133457.10636-3-hdegoede@redhat.com
-
Arnd Bergmann authored
The variable is declared in an #ifdef section, but the user is now unconditional, which leads to a build failure: drivers/gpu/drm/imx/imx-drm-core.c: In function 'imx_drm_bind': drivers/gpu/drm/imx/imx-drm-core.c:264:6: error: 'legacyfb_depth' undeclared (first use in this function); did you mean 'lockdep_depth'? Remove the remaining #ifdef as well. Fixes: f53705fd ("drm/imx: Use drm_fbdev_generic_setup()") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Noralf Trønnes <noralf@tronnes.org> Link: https://patchwork.freedesktop.org/patch/msgid/20180926193846.2490574-1-arnd@arndb.de
-
Heiko Stuebner authored
The hs_start interrupt on rk3188 fires at the start of a new frame, so serves essentially the same purpose as the dsp_hold_valid irq in checking when the last frame got delivered when going to standby. So define it to fix a hang on atomic_disable of the vop because the completion never really completed before. Fixes: 428e15cc ("drm/rockchip: vop: add rk3188 vop definitions") Signed-off-by:
Sandy Huang <hjc@rock-chips.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180923123730.14706-1-heiko@sntech.de
-
Thomas Zimmermann authored
This patch unifies the naming of DRM functions for reference counting of struct drm_device. The resulting code is more aligned with the rest of the Linux kernel interfaces. Signed-off-by:
Thomas Zimmermann <contact@tzimmermann.org> Signed-off-by:
Boris Brezillon <boris.brezillon@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180701132415.10161-1-contact@tzimmermann.org
-
Jernej Skrabec authored
R40 DE2 mixers are similar to those found in A83T, except it needs different clock settings. Add a compatibles for them. Reviewed-by:
Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-14-jernej.skrabec@siol.net
-
Chen-Yu Tsai authored
This reverts commit 3510e7a7. During the 4.19 merge window for drm-misc, two patches critical to supporting the display pipeline on the Allwinner R40 SoC were missed. They were applied later but missed the merge window deadline. As a result 4.19-rc1 kernel would crash on the R40 when it couldn't parse the new device tree structure. We ended up removing support for the R40 display pipeline for 4.19. Since the missing patches are already merged for 4.20, we can now revert the commit that removed support. Signed-off-by:
-
Sean Paul authored
Backmerging 4.19-rc5 to pick up sun4i fix Signed-off-by: -
Dave Airlie authored
Sean Paul requested an -rc5 backmerge from some sun4i fixes. Signed-off-by:Dave Airlie <airlied@redhat.com>
-
Dave Airlie authored
- A crash fix founded in recent linux-next from John Garry - One sparse warning fix from Souptick Joarder - Some xxx_unref cleanup from Thomas Zimmermann Signed-off-by:
-
git://linuxtv.org/pinchartl/mediaDave Airlie authored
R-Car DU support for the D3 and E3 SoCs (v4.20) Signed-off-by:
-
- 26 Sep, 2018 19 commits
-
-
Thomas Zimmermann authored
This patch unifies the naming of DRM functions for reference counting of struct drm_device. The resulting code is more aligned with the rest of the Linux kernel interfaces. Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by:
Stefan Agner <stefan@agner.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20180926114312.23097-1-tzimmermann@suse.de
-
Stefan Agner authored
The driver is mostly in maintenance mode. Using drm-misc is a good fit and should make maintenance a bit easier. Signed-off-by:
Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20180926125034.4095-1-stefan@agner.ch
-
Leonard Crestez authored
The lcdif block is only powered on when display is active so plane updates when not enabled are not valid. Writing to an unpowered IP block is mostly ignored but can trigger bus errors on some chips. Prevent this situation by switching to drm_atomic_helper_commit_tail_rpm and having the drm core ensure atomic_plane_update is only called while the crtc is active. This avoids having to keep track of "enabled" bits inside the mxsfb driver. This also requires handling the vblank event for disable from mxsfb_pipe_disable. Signed-off-by:
Leonard Crestez <leonard.crestez@nxp.com> Suggested-by:
-
Leonard Crestez authored
Since power to the lcdif block can be lost on suspend implement PM_SLEEP_OPS using drm_mode_config_helper_suspend/resume to save/restore the current mode. Signed-off-by:
-
Leonard Crestez authored
Adding lcdif nodes to a power domain currently results in black/corrupted screens or hangs because power is not correctly enabled when required. Ensure power is on when display is active by adding pm_runtime_get/put_sync to mxsfb_pipe_enable/disable. Signed-off-by:
-
Leonard Crestez authored
LCDIF will repeatedly display data from CUR_BUF and set CUR_BUF to NEXT_BUF when done. Since we are only ever writing to NEXT_BUF the display will show an initial corrupt frame. Fix by writing the FB paddr to both CUR_BUF and NEXT_BUF when activating the CRTC. Signed-off-by:
-
Leonard Crestez authored
The main axi clk is disabled at the end of mxsfb_crtc_mode_set_nofb and immediately reenabled in mxsfb_enable_controller. Avoid this by moving the handling of axi clk one level up to mxsfb_crtc_enable. Do the same for mxsfb_crtc_disable for symmetry. This shouldn't have any functional effect. Signed-off-by:
-
Thomas Zimmermann authored
This patch unifies the naming of DRM functions for reference counting of struct drm_device. The resulting code is more aligned with the rest of the Linux kernel interfaces. Signed-off-by:
-
Thomas Zimmermann authored
This patch unifies the naming of DRM functions for reference counting of struct drm_device. The resulting code is more aligned with the rest of the Linux kernel interfaces. Signed-off-by:
-
Sean Paul authored
Another "small driver" moving into drm-misc. Stefan has also offered to co-maintain it. Cc: Marek Vasut <marex@denx.de> Cc: Stefan Agner <stefan@agner.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Acked-by:
-
Ezequiel Garcia authored
Implement vmap/vunmap so we can export dmabufs to other drivers, such as video4linux. Tested with a virtio-gpu / vivid (virtual capture driver) pipeline, where the vivid driver imports the dmabufs exported by virtio-gpu. Note that dma_buf_vmap() does its own vmap counting, so it's not needed to take care of it in the driver. Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Link: http://patchwork.freedesktop.org/patch/msgid/20180925161606.17980-4-ezequiel@collabora.comSigned-off-by:
Gerd Hoffmann <kraxel@redhat.com>
-
Ezequiel Garcia authored
Currently, virtio_gpu_object_kmap() is only called by virtio_gpufb_create(), when a DRM framebuffer is created. Thus, instead of returning the vmap'ed address, emit a warning if virtio_gpu_object_kmap is called on an already mapped object. With this change, kmap/kunmap calls are now balanced. Signed-off-by:
-
Ezequiel Garcia authored
Implement a virtio_gpu_object_kunmap() to unmap the kernel mapping, and use it in the TTM object destroy path. Signed-off-by:
-
Thomas Zimmermann authored
The function ttm_bo_put releases a reference to a TTM buffer object. The function's name is more aligned to the Linux kernel convention of naming ref-counting function _get and _put. A call to ttm_bo_unref takes the address of the TTM BO object's pointer and clears the pointer's value to NULL. This is not necessary in most cases and sometimes even worked around by the calling code. A call to ttm_bo_put only releases the reference without clearing the pointer. The current behaviour of cleaning the pointer is kept in the calling code, but should be removed if not required in a later patch. Signed-off-by:
Xinliang Liu <z.liuxinliang@hisilicon.com> Signed-off-by:
-
Thomas Zimmermann authored
This patch unifies the naming of DRM functions for reference counting of struct drm_device. The resulting code is more aligned with the rest of the Linux kernel interfaces. Signed-off-by:
-
Souptick Joarder authored
convert drm_atomic_helper_suspend/resume() to use drm_mode_config_helper_suspend/resume(). Fixed one sparse warning by making hibmc_drm_interrupt static. Signed-off-by:
Ajit Negi <ajitn.linux@gmail.com> Signed-off-by:
Souptick Joarder <jrdr.linux@gmail.com> Reviewed-by:
-
John Garry authored
Switch to use Huawei PCI vendor ID macro from pci_ids.h file. In addition, switch to use PCI_VDEVICE() instead of open coding. Signed-off-by:
John Garry <john.garry@huawei.com> Reviewed-by:
-
John Garry authored
Currently the driver overwrites the surface depth provided by the fb helper to give an invalid bpp/surface depth combination. This has been exposed by commit 70109354 ("drm: Reject unknown legacy bpp and depth for drm_mode_addfb ioctl"), which now causes the driver to fail to probe. Fix by not overwriting the surface depth. Fixes: d1667b86 ("drm/hisilicon/hibmc: Add support for frame buffer") Signed-off-by:
-
John Garry authored
In hibmc_drm_fb_create(), when the call to hibmc_framebuffer_init() fails with error, do not store the error code in the HiBMC device frame-buffer pointer, as this will be later checked for non-zero value in hibmc_fbdev_destroy() when our intention is to check for a valid function pointer. This fixes the following crash: [ 9.699791] Unable to handle kernel NULL pointer dereference at virtual address 000000000000001a [ 9.708672] Mem abort info: [ 9.711489] ESR = 0x96000004 [ 9.714570] Exception class = DABT (current EL), IL = 32 bits [ 9.720551] SET = 0, FnV = 0 [ 9.723631] EA = 0, S1PTW = 0 [ 9.726799] Data abort info: [ 9.729702] ISV = 0, ISS = 0x00000004 [ 9.733573] CM = 0, WnR = 0 [ 9.736566] [000000000000001a] user address but active_mm is swapper [ 9.742987] Internal error: Oops: 96000004 [#1] PREEMPT SMP [ 9.748614] Modules linked in: [ 9.751694] CPU: 16 PID: 293 Comm: kworker/16:1 Tainted: G W 4.19.0-rc4-next-20180920-00001-g9b0012c #322 [ 9.762681] Hardware name: Huawei Taishan 2280 /D05, BIOS Hisilicon D05 IT21 Nemo 2.0 RC0 04/18/2018 [ 9.771915] Workqueue: events work_for_cpu_fn [ 9.776312] pstate: 60000005 (nZCv daif -PAN -UAO) [ 9.781150] pc : drm_mode_object_put+0x0/0x20 [ 9.785547] lr : hibmc_fbdev_fini+0x40/0x58 [ 9.789767] sp : ffff00000af1bcf0 [ 9.793108] x29: ffff00000af1bcf0 x28: 0000000000000000 [ 9.798473] x27: 0000000000000000 x26: ffff000008f66630 [ 9.803838] x25: 0000000000000000 x24: ffff0000095abb98 [ 9.809203] x23: ffff8017db92fe00 x22: ffff8017d2b13000 [ 9.814568] x21: ffffffffffffffea x20: ffff8017d2f80018 [ 9.819933] x19: ffff8017d28a0018 x18: ffffffffffffffff [ 9.825297] x17: 0000000000000000 x16: 0000000000000000 [ 9.830662] x15: ffff0000092296c8 x14: ffff00008939970f [ 9.836026] x13: ffff00000939971d x12: ffff000009229940 [ 9.841391] x11: ffff0000085f8fc0 x10: ffff00000af1b9a0 [ 9.846756] x9 : 000000000000000d x8 : 6620657a696c6169 [ 9.852121] x7 : ffff8017d3340580 x6 : ffff8017d4168000 [ 9.857486] x5 : 0000000000000000 x4 : ffff8017db92fb20 [ 9.862850] x3 : 0000000000002690 x2 : ffff8017d3340480 [ 9.868214] x1 : 0000000000000028 x0 : 0000000000000002 [ 9.873580] Process kworker/16:1 (pid: 293, stack limit = 0x(____ptrval____)) [ 9.880788] Call trace: [ 9.883252] drm_mode_object_put+0x0/0x20 [ 9.887297] hibmc_unload+0x1c/0x80 [ 9.890815] hibmc_pci_probe+0x170/0x3c8 [ 9.894773] local_pci_probe+0x3c/0xb0 [ 9.898555] work_for_cpu_fn+0x18/0x28 [ 9.902337] process_one_work+0x1e0/0x318 [ 9.906382] worker_thread+0x228/0x450 [ 9.910164] kthread+0x128/0x130 [ 9.913418] ret_from_fork+0x10/0x18 [ 9.917024] Code: a94153f3 a8c27bfd d65f03c0 d503201f (f9400c01) [ 9.923180] ---[ end trace 2695ffa0af5be375 ]--- Fixes: d1667b86 ("drm/hisilicon/hibmc: Add support for frame buffer") Signed-off-by:
-
- 25 Sep, 2018 1 commit
-
-
Gerd Hoffmann authored
Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20180921134704.12826-7-kraxel@redhat.com
-
