This feature has been causing trouble - disable it for now.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Prevent sched scan while not idle (including during association or in AP
mode) instead of while associated only.

This fixes my previous commit which was incomplete:

commit bd5e4744
Author: David Spinadel <david.spinadel@intel.com>
Date:   Thu Apr 24 13:15:29 2014 +0300

    iwlwifi: mvm: do no sched scan while associated

    Currently the FW doesn't support sched scan while associated,
    Prevent it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

tail should be equal to the last valid index, so
decrease it by one.

This error causes in "a gap" in some cases (as well as
some possible out-of-bound write), finally resulting in
ucode assertion.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There was a deadlock in monitor mode when we were setting the
channel if the channel was not 1.

======================================================
[ INFO: possible circular locking dependency detected ]
3.14.3 #4 Not tainted
-------------------------------------------------------
iw/3323 is trying to acquire lock:
 (&local->chanctx_mtx){+.+.+.}, at: [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211]

but task is already holding lock:
 (&local->iflist_mtx){+.+...}, at: [<ffffffffa0609e0a>] ieee80211_set_monitor_channel+0x5a/0x1b0 [mac80211]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (&local->iflist_mtx){+.+...}:
       [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
       [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
       [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
       [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
       [<ffffffffa0518189>] iwl_mvm_recalc_multicast+0x49/0xa0 [iwlmvm]
       [<ffffffffa051822e>] iwl_mvm_configure_filter+0x4e/0x70 [iwlmvm]
       [<ffffffffa05e6d43>] ieee80211_configure_filter+0x153/0x5f0 [mac80211]
       [<ffffffffa05e71f5>] ieee80211_reconfig_filter+0x15/0x20 [mac80211]
       [snip]

-> #1 (&mvm->mutex){+.+.+.}:
       [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
       [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
       [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
       [<ffffffffa0517246>] iwl_mvm_add_chanctx+0x56/0xe0 [iwlmvm]
       [<ffffffffa062ca1e>] ieee80211_new_chanctx+0x13e/0x410 [mac80211]
       [<ffffffffa062d953>] ieee80211_vif_use_channel+0x1c3/0x5a0 [mac80211]
       [<ffffffffa06035ab>] ieee80211_add_virtual_monitor+0x1ab/0x6b0 [mac80211]
       [<ffffffffa06052ea>] ieee80211_do_open+0xe6a/0x15a0 [mac80211]
       [<ffffffffa0605a79>] ieee80211_open+0x59/0x60 [mac80211]
       [snip]

-> #0 (&local->chanctx_mtx){+.+.+.}:
       [<ffffffff810d6cb7>] check_prevs_add+0x977/0x980
       [<ffffffff810d95bb>] __lock_acquire+0xb3b/0x13b0
       [<ffffffff810d9ee0>] lock_acquire+0xb0/0x1f0
       [<ffffffff817eb9c8>] mutex_lock_nested+0x78/0x4f0
       [<ffffffffa062e2f2>] ieee80211_vif_release_channel+0x42/0xb0 [mac80211]
       [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211]
       [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211]
       [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211]
       [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211]
       [snip]

other info that might help us debug this:

Chain exists of:
  &local->chanctx_mtx --> &mvm->mutex --> &local->iflist_mtx

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&local->iflist_mtx);
                               lock(&mvm->mutex);
                               lock(&local->iflist_mtx);
  lock(&local->chanctx_mtx);

 *** DEADLOCK ***

This deadlock actually occurs:
INFO: task iw:3323 blocked for more than 120 seconds.
      Not tainted 3.14.3 #4
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
iw              D ffff8800c8afcd80  4192  3323   3322 0x00000000
 ffff880078fdb7e0 0000000000000046 ffff8800c8afcd80 ffff880078fdbfd8
 00000000001d5540 00000000001d5540 ffff8801141b0000 ffff8800c8afcd80
 ffff880078ff9e38 ffff880078ff9e38 ffff880078ff9e40 0000000000000246
Call Trace:
 [<ffffffff817ea841>] schedule_preempt_disabled+0x31/0x80
 [<ffffffff817ebaed>] mutex_lock_nested+0x19d/0x4f0
 [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
 [<ffffffffa06225cf>] ? ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
 [<ffffffffa052a680>] ? iwl_mvm_power_mac_update_mode+0xc0/0xc0 [iwlmvm]
 [<ffffffffa06225cf>] ieee80211_iterate_active_interfaces+0x2f/0x60 [mac80211]
 [<ffffffffa0529357>] _iwl_mvm_power_update_binding+0x27/0x80 [iwlmvm]
 [<ffffffffa0516eb1>] iwl_mvm_unassign_vif_chanctx+0x81/0xc0 [iwlmvm]
 [<ffffffffa062d3ff>] __ieee80211_vif_release_channel+0xdf/0x470 [mac80211]
 [<ffffffffa062e2fa>] ieee80211_vif_release_channel+0x4a/0xb0 [mac80211]
 [<ffffffffa0609ec3>] ieee80211_set_monitor_channel+0x113/0x1b0 [mac80211]
 [<ffffffffa058fb37>] cfg80211_set_monitor_channel+0x77/0x2b0 [cfg80211]
 [<ffffffffa056e0b2>] __nl80211_set_channel+0x122/0x140 [cfg80211]
 [<ffffffffa0581374>] nl80211_set_wiphy+0x284/0xaf0 [cfg80211]

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75541

Cc: <stable@vger.kernel.org> [3.13+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case RFKILL is in KILL position, the NIC will issue an
interrupt straight away. This interrupt won't be sent
because it is masked in the hardware.
But if our interrupt service routine is called for another
reason (SHARED_IRQ), then we'll look at the interrupt cause
and service it. This can cause bad things if we are not
ready yet.
Explicitly clean the interrupt cause register to make sure
we won't service anything before we are ready to.

Cc: <stable@vger.kernel.org> [3.14]
Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently the FW doesn't support sched scan while associated,
Prevent it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

My bad - I forgot to update this when sending the patch
upstream.

Fixes: 87d5e415 ("iwlwifi: mvm: rs: reinit rs if no tx for a long time")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The commit below introduced a bug in the validity bits in
init. Due to that, all the Coex mechanism stopped sending
kills to the BT side. Fix that.

Fixes: b9fae2d5 ("iwlwifi: mvm: BT Coex add support for Co-running block")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware doesn't handle properly the fragmented scan.
Stop using it.
While at it change max_out_time and suspend_time units from
usec to TUs as expected by firmware API.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A few entries were wrong and this caused throughput issues.

Cc: <stable@vger.kernel.org> [3.13+]
Fixes: dac94da8 ("iwlwifi: mvm: new BT Coex API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The per rate stats should be cleared when aggregation state changes
to avoid making rate scale decisions based on throughput figures which
were collected prior to the aggregation state change and are now stale.
While at it make sure any clearing of the per rate stats will get logged.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't search columns which are unlikely to succeed as previous
columns searched with less aggressive modulation failed.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow switching back to legacy Tx columns so we'll stop doing
HT/VHT in case we're far from the AP. Stop active aggregation when
making a deciding to stay in a legacy column.
Despite having low legacy rates in the LQ table lower entries
it doesn't help much in case we're doing aggregations as the
aggregation was being transmitted in the initial rate of the table.

This should help traffic stalls when far from the AP.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

After being idle for a long time (>5sec) the rs statistics
will be stale so we prefer to reset rs and start from legacy
rates again. This gives better results when the attenuation
increased signficantly (e.g. we got further from the AP) and
after a while we start Tx
Note that the first Tx after the idle period will still go out
in the old modulation and rate but this seemed a simpler approach
compared to adding a timer or modifying mac80211 for this.
The negative impact is negligble as we'll recover quickly.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Change the down/upscale decision logic a bit to be based
on different success ratio thresholds. This fixes the implementation
compared to the rate scale algorithm which was planned to yield
optimal results. Also fix a case where a lower rate wasn't explored
despite being a potential for better throughput.
While at it rewrite rs_get_rate_action to be more clear and clean.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The selection of the max expected throughput for a column
didn't take into account the maximal allowed rate for the current
peer. This can cause unnecessary switches during the search cycle
to columns which have no chance of beating the current throughput.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

It was missing.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to load the new firmware.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add 2 new HW IDs for the 7265 series.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

I forgot to send the new Look Up Table to the firmware and
I also forgot to free the command which is kzalloc'ed.
This code is relevant for 7265 device only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

mimo_delim was always set to 0 instead of pointing to
the first SISO entry after MIMO rates.
This can cause keep transmitting in MIMO even when we shouldn't.
For example when the peer is requesting static SMPS.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If we have no beacon data before association, delay smart FIFO
enablement until after we have this data.

Not doing so can cause association failures in extremely silent
environments (usually only a shielded box/room) as beacon RX is
not sent to the host immediately, and then the association time
event ends without the host receiving any beacon even though it
was on the air - it's just stuck on the FIFO.

Cc: <stable@vger.kernel.org> [3.14]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to support the driver behaviour introduced by:

   commit d0575a5a703978c43e25128421158c78534ba100
   Author: Daniel Kim <dekim@broadcom.com>
   Date:   Wed Mar 12 18:12:14 2014 -0700

       brcmfmac: Enable 40MHz bandwidth in 2GHz band and OBSS scanning

in devices that do not support bwcap firmware command a fallback
is added.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the function brcmf_sdiod_request_data() an error message is logged,
but the calling function retries it. This patch will only log an error
message when retry limit is reached. The low-level error is still
logged by a SDIO debug message.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The watchdog thread waits on completion that is set from a timer. As
the completion is count based this could mean that on a busy system
the watchdog is handled multiple times with a very short interval.
This is not the intended behaviour. After handling the watchdog it
should wait for the next timer expiry. This is accomplished by
reinitializing the completion.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch enables 40MHz bandwidth in 2GHz band after checking whether
cfg80211 allows it or not, and enables OBSS scanning operations to
to support 20/40 BSS coexistence.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

In Secure Connections Only mode, it is required that Secure Connections
is used for pairing and that the link key is encrypted with AES-CCM using
a P-256 authenticated combination key. If this is not the case, then new
connection shall be refused or existing connections shall be dropped.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

It is possible that pairing fails after we've already received remote
identity information. One example of such a situation is when
re-encryption using the LTK fails. In this case the hci_conn object has
already been updated with the identity address but user space does not
yet know about it (since we didn't notify it of the new IRK yet).

To ensure user space doesn't get a Pair Device command response with an
unknown address always use the same address in the response as was used
for the original command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When performing SMP pairing with MITM protection one side needs to
enter the passkey while the other side displays to the user what needs
to be entered. Nowhere in the SMP specification does it say that the
displaying side needs to any kind of confirmation of the passkey, even
though a code comment in smp.c implies this.

This patch removes the misleading comment and converts the code to use
the passkey notification mgmt event instead of the passkey confirmation
mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In some cases the current 250ms delay is not enough for the remote to
receive the keys, as can be witnessed by the following log:

> ACL Data RX: Handle 64 flags 0x02 dlen 21               [hci1] 231.414217
      SMP: Signing Information (0x0a) len 16
        Signature key: 555bb66b7ab3abc9d5c287c97fe6eb29
< ACL Data TX: Handle 64 flags 0x00 dlen 21               [hci1] 231.414414
      SMP: Encryption Information (0x06) len 16
        Long term key: 2a7cdc233c9a4b1f3ed31dd9843fea29
< ACL Data TX: Handle 64 flags 0x00 dlen 15               [hci1] 231.414466
      SMP: Master Identification (0x07) len 10
        EDIV: 0xeccc
        Rand: 0x322e0ef50bd9308a
< ACL Data TX: Handle 64 flags 0x00 dlen 21               [hci1] 231.414505
      SMP: Signing Information (0x0a) len 16
        Signature key: bbda1b2076e2325aa66fbcdd5388f745
> HCI Event: Number of Completed Packets (0x13) plen 5    [hci1] 231.483130
        Num handles: 1
        Handle: 64
        Count: 2
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28  [hci1] 231.664211
        Handle: 64
        Random number: 0x5052ad2b75fed54b
        Encrypted diversifier: 0xb7c2
        Long term key: a336ede66711b49a84bde9b41426692e
> HCI Event: Command Status (0x0f) plen 4                 [hci1] 231.666937
      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
> HCI Event: Number of Completed Packets (0x13) plen 5    [hci1] 231.712646
        Num handles: 1
        Handle: 64
        Count: 1
> HCI Event: Disconnect Complete (0x05) plen 4            [hci1] 232.562587
        Status: Success (0x00)
        Handle: 64
        Reason: Remote User Terminated Connection (0x13)

As can be seen, the last key (Signing Information) is sent at 231.414505
but the completed packets event for it comes only at 231.712646,
i.e. roughly 298ms later.

To have a better margin of error this patch increases the delay to
500ms.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This is a trivial coding style simplification by instead of having an
extra early return to instead revert the if condition and do the single
needed queue_work() call there.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Macro ASSERT_RDEV_LOCK(rdev) is equal to ASSERT_RTNL(), so replace it
with ASSERT_RTNL() and remove it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

RCU pointer bss->pub.beacon_ies is checked before in previous
statement:

if (rcu_access_pointer(bss->pub.beacon_ies))
	continue;

There is no need to check it twice(and in the wrong way :) ).
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a bit in rx_status.vht_flags to let the low level driver
notify mac80211 about a beamformed packet. Propagate this
to the radiotap header.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

On 2.4Ghz band, the channels overlap since the delta
between different channels is 5Mhz while the width of the
receiver is 20Mhz (at least).

This means that we can hear beacons or probe responses from
adjacent channels. These frames will have a significant
lower RSSI which will feed all kinds of logic with inaccurate
data. An obvious example is the roaming algorithm that will
think our AP is getting weak and will try to move to another
AP.

In order to avoid this, update the signal only if the frame
has been heard on the same channel as the one advertised by
the AP in its DS / HT IEs.
We refrain from updating the values only if the AP is
already in the BSS list so that we will still have a valid
(but inaccurate) value if the AP was heard on an adjacent
channel only.

To achieve this, stop taking the channel from DS / HT IEs
in mac80211. The DS / HT IEs is taken into account to
discard the frame if it was received on a disabled channel.
This can happen due to the same phenomenon: the frame is
sent on channel 12, but heard on channel 11 while channel
12 can be disabled on certain devices. Since this check
is done in cfg80211, stop even checking this in mac80211.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove unused rx_freq variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Function __cfg80211_join_ibss() is only used in net/wireless/ibss.c,
so make it static.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Drivers might want to have private data in addition
to all other ieee80211_tx_info.status fields.

The current ieee80211_tx_info.rate_driver_data overlaps
with some of the non-rate data (e.g. ampdu_ack_len), so
it might not be good enough.

Since we already know how much free bytes remained,
simply use this size to define (void *) array.

While on it, change ack_signal type from int to the more
explicit s32 type.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Assuming sched_scan_stop operation is synchronous the driver may not
necessary call ieee80211_sched_scan_stopped_work. Since this work is
the only place where sched_scan_sdata is released we can possibly run
into situation when it is never released. Fix this by releasing it
just after calling drv_sched_scan_stop.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>