- 27 Oct, 2017 32 commits
-
-
Jacob Chen authored
When I was supporting Rpi Camera Module on the ASUS Tinker board, I found this driver have some issues with rockchip's mipi-csi driver. It didn't place clock lane in LP-11 state before performing D-PHY initialisation. >From our experience, on some OV sensors, LP-11 state is not achieved while BIT(5)-0x4800 is cleared. So let's set BIT(5) and BIT(0) both while not streaming, in order to coax the clock lane into LP-11 state. 0x4800 : MIPI CTRL 00 BIT(5) : clock lane gate enable 0: continuous 1: none-continuous BIT(0) : manually set clock lane 0: Not used 1: used Signed-off-by:
Jacob Chen <jacob-chen@iotwrt.com> Reviewed-by:
Luis Oliveira <lolivei@synopsys.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Wenyou Yang authored
Add the ov7670_s_power function which is responsible for manipulating the power dowm mode through the PWDN pin and the reset operation through the RESET pin, and keep it powered at all times. [sakari.ailus@linux.intel.com: set pwdn_gpio direction only once] Signed-off-by:
Wenyou Yang <wenyou.yang@microchip.com> Signed-off-by:
-
Wenyou Yang authored
Add the get_fmt callback, also enable V4L2_SUBDEV_FL_HAS_DEVNODE flag to make this subdev has device node. Signed-off-by:
-
Wenyou Yang authored
Add the media entity pads initialization. Signed-off-by:
-
Hans Verkuil authored
This driver adds support for the Tegra CEC IP. It is based on the NVIDIA drivers/misc/tegra-cec driver in their 3.10 kernel. This has been converted to the CEC framework and cleaned up. Tested with my Jetson TK1 board. It has also been tested with the Tegra X1 in an embedded product. Note of warning for the Tegra X2: this SoC supports two HDMI outputs, but only one CEC adapter and the CEC bus is shared between the two outputs. This is a design mistake and the CEC adapter can control only one HDMI output. Never hook up both HDMI outputs to the CEC bus in a hardware design: this is illegal as per the CEC specification. The CEC bus can be shared between multiple inputs and zero or one outputs, but not between multiple outputs. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Hans Verkuil authored
This documents the binding for the Tegra CEC module. Signed-off-by:
Rob Herring <robh@kernel.org> Acked-by:
-
Jérémy Lefaure authored
Using the ARRAY_SIZE macro improves the readability of the code. Also, it is useless to use a variable to store this constant calculated at compile time. Found with Coccinelle with the following semantic patch: @r depends on (org || report)@ type T; T[] E; position p; @@ ( (sizeof(E)@p /sizeof(*E)) | (sizeof(E)@p /sizeof(E[...])) | (sizeof(E)@p /sizeof(T)) ) Signed-off-by:
Jérémy Lefaure <jeremy.lefaure@lse.epita.fr> Signed-off-by:
-
Muhammad Falak R Wani authored
The functions __bo_alloc, __bo_search_and_remove_from_free_rbtree, __bo_search_by_addr, __bo_search_by_addr_in_range, __bo_break_up and __bo_merge are local to the source and do not need to be in the global scope, so make them static. Cleans up sparse warnings: warning: symbol '__bo_alloc' was not declared. Should it be static? warning: symbol '__bo_search_and_remove_from_free_rbtree' was not declared. Should it be static? warning: symbol '__bo_search_by_addr' was not declared. Should it be static? warning: symbol '__bo_search_by_addr_in_range' was not declared. Should it be static? warning: symbol '__bo_break_up' was not declared. Should it be static? warning: symbol '__bo_merge' was not declared. Should it be static? Signed-off-by:
Muhammad Falak R Wani <falakreyaz@gmail.com> Signed-off-by:
-
Sakari Ailus authored
There was no specific item regarding what should be done to sensor, lens and flash drivers. Add one, to replace the vague item denoting support only to particular sensor, lens and flash devices. Signed-off-by:
-
Sakari Ailus authored
By adding the "atomisp-" prefix to module names (and "ATOMISP_" to Kconfig options), the staging drivers for e.g. sensors are labelled as being specific to atomisp, which they effectively are. Signed-off-by:
-
Sakari Ailus authored
Add the maintainers entry to the atomisp staging media driver. Signed-off-by:
-
Leon Luo authored
The imx274 is a Sony CMOS image sensor that has 1/2.5 image size. It supports up to 3840x2160 (4K) 60fps, 1080p 120fps. The interface is 4-lane MIPI CSI-2 running at 1.44Gbps each. This driver has been tested on Xilinx ZCU102 platform with a Leopard LI-IMX274MIPI-FMC camera board. Support for the following features: -Resolutions: 3840x2160, 1920x1080, 1280x720 -Frame rate: 3840x2160 : 5 – 60fps 1920x1080 : 5 – 120fps 1280x720 : 5 – 120fps -Exposure time: 16 – (frame interval) micro-seconds -Gain: 1x - 180x -VFLIP: enable/disabledrivers/media/i2c/imx274.c -Test pattern: 12 test patterns Signed-off-by:Leon Luo <leonl@leopardimaging.com> Tested-by:
Sören Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by:
-
Leon Luo authored
The binding file for imx274 CMOS sensor V4l2 driver Signed-off-by:
-
Philipp Zabel authored
The TC358743 is an HDMI to MIPI CSI2-2 bridge. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Tim Harvey authored
When using VDIC with CSI1, make sure to select the correct CSI in IPU_CONF. Fixes: f0d9c892 ("[media] media: imx: Add IC subdev drivers") Suggested-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Tim Harvey <tharvey@gateworks.com> Acked-by:
Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by:
-
Dan Carpenter authored
We can remove the check for if "state->cec_adap" is NULL. The cec_allocate_adapter() function never returns NULL and also we verified that "state->cec_adap" is an error pointer. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Bhumika Goyal authored
Make vb2_ops const as they are only stored in the const field of a vb2_queue structure. Make the declarations const too. Done using Coccinelle. Signed-off-by:
Bhumika Goyal <bhumirks@gmail.com> Signed-off-by:
-
Bhumika Goyal authored
Make vb2_ops const as they are only stored in the const field of a vb2_queue structure. Make the declarations const too. Done using Coccinelle. Signed-off-by:
-
Bhumika Goyal authored
Make this const as it is only used in a copy operation in the file referencing it. Make the declaration const too. Done using Coccinelle. Signed-off-by:
-
Bhumika Goyal authored
Make this const as it is only passed to the const argument of the function videobuf_queue_sg_init in the file referencing it. Also, make the declaration in the header const. Structure found using Coccinelle and changes done by hand. Signed-off-by:
-
Arvind Yadav authored
kasprintf() can fail here and we must check its return value. Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Reviewed-by:
-
Jacob Chen authored
It should be "LP-11". Signed-off-by:
-
Markus Elfring authored
- Delete seven error messages for a failed memory allocation - Adjust seven checks for null pointers - Use common error handling code in tm6000_usb_probe() - Adjust jump targets so that the function "kfree" will be always called with a non-null pointer. - Delete an initialisation for the local variable "dev" which became unnecessary with this refactoring. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
Hans Verkuil authored
The kAPI cec-pin.h header also defined data structures that did not belong here but were private to the CEC core code. Split that part off into a cec-pin-priv.h header. Signed-off-by:
Hans Verkuil <hansverk@cisco.com> Signed-off-by:
-
Stanimir Varbanov authored
This addresses the wrong behavior of decoder stop command by rewriting it. These new implementation enqueue an empty buffer on the decoder input buffer queue to signal end-of-stream. The client should stop queuing buffers on the V4L2 Output queue and continue queuing/dequeuing buffers on Capture queue. This process will continue until the client receives a buffer with V4L2_BUF_FLAG_LAST flag raised, which means that this is last decoded buffer with data. Signed-off-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Tested-by:
Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by:
-
Wei Yongjun authored
In case of error, the function platform_device_register_data() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Acked-by:
Helen Koike <helen.koike@collabora.com> Signed-off-by:
-
Stanimir Varbanov authored
This fixes wrongly filled bytesused field of v4l2_plane structure by include data_offset in the plane, Also fill data_offset and bytesused for capture type of buffers only. Signed-off-by:
-
Wenyou Yang authored
To improve the readability of code, split the format array into two, one for the format description, other for the register configuration. Meanwhile, add the flag member to indicate the format can be achieved from the sensor or be produced by the controller, and rename members related to the register configuration. Also add more formats support: GREY, ARGB444, ARGB555 and ARGB32. Signed-off-by:
-
Wenyou Yang authored
Remove the memeber *config from the isc_subdev_entity struct, the member is useless afterward. Signed-off-by:
-
Wenyou Yang authored
To meet the relationship, enable the HCLOCK and ispck during the device probe, "isc_pck frequency is less than or equal to isc_ispck, and isc_ispck is greater than or equal to HCLOCK." Meanwhile, call the pm_runtime_enable() in the right place. Signed-off-by:
-
Wenyou Yang authored
A software write operation to the ISC_CLKEN or ISC_CLKDIS register requires double clock domain synchronization and is not permitted when the ISC_SR.SIP is asserted. So add the .prepare and .unprepare ops to make sure the ISC_CLKSR.SIP is unasserted before the write operation to the ISC_CLKEN or ISC_CLKDIS register. Signed-off-by:
-
Wenyou Yang authored
Add the spin lock for the clock enable and disable operations. Signed-off-by:
-
- 24 Oct, 2017 3 commits
-
-
Stanimir Varbanov authored
This change will fix an issue with dma_free size found with DMA API debug enabled. Signed-off-by:
-
Sakari Ailus authored
Instead of relying on a mix of runtime PM and the s_power() callback, drop the s_power() callback altogether and use runtime PM solely. As device access is required during device power-on and power-off sequences, runtime PM alone cannot tell whether the device is available. Thus the "active" field is introduced in struct smiapp_sensor to tell whether it is safe to write to the device. Consequently there is no need to power on the device whenever a file handle is open. This functionality is removed as well. The user may still control the device power management through sysfs. Autosuspend remains enabled, with 1 s delay. Signed-off-by:
-
Sakari Ailus authored
Use unlocked __v4l2_ctrl_handler_setup() in order to make the control setup atomic. Signed-off-by:
-
- 18 Oct, 2017 1 commit
-
-
Mauro Carvalho Chehab authored
* commit '3728e6a2': (904 commits) Linux 4.14-rc5 x86/microcode: Do the family check first locking/lockdep: Disable cross-release features for now x86/mm: Flush more aggressively in lazy TLB mode mm, swap: use page-cluster as max window of VMA based swap readahead mm: page_vma_mapped: ensure pmd is loaded with READ_ONCE outside of lock kmemleak: clear stale pointers from task stacks fs/binfmt_misc.c: node could be NULL when evicting inode fs/mpage.c: fix mpage_writepage() for pages with buffers linux/kernel.h: add/correct kernel-doc notation tty: fall back to N_NULL if switching to N_TTY fails during hangup Revert "vmalloc: back off when the current task is killed" mm/cma.c: take __GFP_NOWARN into account in cma_alloc() scripts/kallsyms.c: ignore symbol type 'n' userfaultfd: selftest: exercise -EEXIST only in background transfer mm: only display online cpus of the numa node mm: remove unnecessary WARN_ONCE in page_vma_mapped_walk(). mm/mempolicy: fix NUMA_INTERLEAVE_HIT counter include/linux/of.h: provide of_n_{addr,size}_cells wrappers for !CONFIG_OF mm/madvise.c: add description for MADV_WIPEONFORK and MADV_KEEPONFORK ...
-
- 17 Oct, 2017 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-mediaLinus Torvalds authored
Pull media fixes from Mauro Carvalho Chehab: "Core fixes: - cec: Respond to unregistered initiators, when applicable - dvb_frontend: only use kref after initialized Driver-specific fixes: - qcom, camss: Make function vfe_set_selection static - qcom: VIDEO_QCOM_CAMSS should depend on HAS_DMA - s5p-cec: add NACK detection support - media: staging/imx: Fix uninitialized variable warning - dib3000mc: i2c transfers over usb cannot be done from stack - venus: init registered list on streamoff" * tag 'media/v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: media: dvb_frontend: only use kref after initialized media: platform: VIDEO_QCOM_CAMSS should depend on HAS_DMA media: cec: Respond to unregistered initiators, when applicable media: s5p-cec: add NACK detection support media: staging/imx: Fix uninitialized variable warning media: qcom: camss: Make function vfe_set_selection static media: venus: init registered list on streamoff media: dvb: i2c transfers over usb cannot be done from stack
-
- 16 Oct, 2017 3 commits
-
-
Sakari Ailus authored
Most devices do not support lane reordering and in many cases the documentation of the data-lanes property is incomplete for such devices. Document that in case the lane reordering isn't supported, monotonically incremented values from 0 or 1 shall be used. Signed-off-by:
-
Sakari Ailus authored
Port and endpoint numbering has been omitted in DT binding documentation for a large number of devices. Also common properties the device uses have been missed in binding documentation. Make it explicit that these things need to be documented. Signed-off-by:
-
Markus Elfring authored
The script “checkpatch.pl” pointed information out like the following. Comparison to NULL could be written... Thus fix the affected source code places. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
