Update the provider and client documentation with details about the
metadata support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20191223110458.30766-4-peter.ujfalusi@ti.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

This is for dependency of new TI ringacc dmaengine drivers

Merge tag 'drivers_soc_for_5.6' into topic/ti

SOC: TI Keystone Ring Accelerator driver

The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.

The RINGACC converts constant-address read and write accesses to equivalent
read or write accesses to a circular data structure in memory. The RINGACC
eliminates the need for each DMA controller which needs to access ring
elements from having to know the current state of the ring (base address,
current offset). The DMA controller performs a read or write access to a
specific address range (which maps to the source interface on the RINGACC)
and the RINGACC replaces the address for the transaction with a new address
which corresponds to the head or tail element of the ring (head for reads,
tail for writes). Since the RINGACC maintains the state, multiple DMA
controllers or channels are allowed to coherently share the same rings as
applicable. The RINGACC is able to place data which is destined towards
software into cached memory directly.

Supported ring modes:
- Ring Mode
- Messaging Mode
- Credentials Mode
- Queue Manager Mode

TI-SCI integration:

Texas Instrument's System Control Interface (TI-SCI) Message Protocol now
has control over Ringacc module resources management (RM) and Rings
configuration.

The corresponding support of TI-SCI Ringacc module RM protocol
introduced as option through DT parameters:
- ti,sci: phandle on TI-SCI firmware controller DT node
- ti,sci-dev-id: TI-SCI device identifier as per TI-SCI firmware spec

if both parameters present - Ringacc driver will configure/free/reset Rings
using TI-SCI Message Ringacc RM Protocol.

The Ringacc driver manages Rings allocation by itself now and requests
TI-SCI firmware to allocate and configure specific Rings only. It's done
this way because, Linux driver implements two stage Rings allocation and
configuration (allocate ring and configure ring) while TI-SCI Message
Protocol supports only one combined operation (allocate+configure).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x and j721e.

This patch introduces RINGACC device tree bindings.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>

On prep, a spin lock is taken and the next entry in the circular buffer
is filled. On submit, the valid bit is set in the hardware descriptor
and the lock is released.

The DMA engine is started (if it's not already running) when the client
calls dma_async_issue_pending().
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20200103212021.2881-4-logang@deltatee.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Allocate DMA coherent memory for the ring of DMA descriptors and
program the appropriate hardware registers.

A tasklet is created which is triggered on an interrupt to process
all the finished requests. Additionally, any remaining descriptors
are aborted when the hardware is removed or the resources freed.

Use an RCU pointer to synchronize PCI device unbind.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20200103212021.2881-3-logang@deltatee.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Some PLX Switches can expose DMA engines via extra PCI functions
on the upstream port. Each function will have one DMA channel.

This patch is just the core PCI driver skeleton and dma
engine registration.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20200103212021.2881-2-logang@deltatee.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The current descriptor is not on any list of the virtual DMA channel.
Once sdma_terminate_all() is called when a descriptor is currently
in flight then this one is forgotten to be freed. We have to call
vchan_terminate_vdesc() on this descriptor to re-add it to the lists.
Now that we also free the currently running descriptor we can (and
actually have to) remove the current descriptor from its list also
for the cyclic case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/20191216105328.15198-10-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

In sdma_tx_status() we must first find the current sdma_desc. In cyclic
mode we assume that this can always be found with vchan_find_desc().
This is true because do not remove the current descriptor from the
desc_issued list:

	/*
	 * Do not delete the node in desc_issued list in cyclic mode, otherwise
	 * the desc allocated will never be freed in vchan_dma_desc_free_list
	 */
	if (!(sdmac->flags & IMX_DMA_SG_LOOP))
		list_del(&vd->node);

We will change this in the next step, so check if the current descriptor is
the desired one also for the cyclic case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20191216105328.15198-9-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

Rename sdma_disable_channel_async() after the hook it implements, like
done for all other functions in the SDMA driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20191216105328.15198-8-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

vchan_dma_desc_free_list() basically open codes vchan_vdesc_fini() in its
loop body. Call it directly rather than duplicating the code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191216105328.15198-7-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

All list operations are protected by &vc->lock. As vchan_vdesc_fini()
is called unlocked add the missing locking around the list operations.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191216105328.15198-6-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

vchan_vdesc_fini() shouldn't be called under a spin_lock. This is done
in two places, once in vchan_terminate_vdesc() and once in
vchan_synchronize(). Instead of freeing the vdesc right away, collect
the aborted vdescs on a separate list and free them along with the other
vdescs. The terminated descs are also freed in vchan_synchronize as done
before this patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191216105328.15198-5-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

vchan_dma_desc_free_list() basically open codes vchan_vdesc_fini() in
the loop body. One difference is an additional debug message. As this
isn't overly useful remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191216105328.15198-4-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

Originally freeing descriptors was split into a locked and an unlocked
part. The locked part in vchan_get_all_descriptors() collected all
descriptors on a separate list_head. This was done to allow iterating
over that new list in vchan_dma_desc_free_list() without a lock held.

This became broken in 13bb26ae ("dmaengine: virt-dma: don't always
free descriptor upon completion"). With this commit
vchan_dma_desc_free_list() no longer exclusively operates on the
separate list, but starts to put descriptors which can be reused back on
&vc->desc_allocated. This list operation should have been locked, but
wasn't.
In the mean time drivers started to call vchan_dma_desc_free_list() with
their lock held so that we now have the situation that
vchan_dma_desc_free_list() is called locked from some drivers and
unlocked from others.
To clean this up we have to do two things:

1. Add missing locking in vchan_dma_desc_free_list()
2. Make sure drivers call vchan_dma_desc_free_list() unlocked

This needs to be done atomically, so in this patch the locking is added
and all drivers are fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Green Wan <green.wan@sifive.com>
Tested-by: Green Wan <green.wan@sifive.com>
Link: https://lore.kernel.org/r/20191216105328.15198-3-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

vchan_vdesc_fini() can't be called locked. Instead, call
vchan_terminate_vdesc() which delays the freeing of the descriptor to
vchan_synchronize().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20191216105328.15198-2-s.hauer@pengutronix.deSigned-off-by: Vinod Koul <vkoul@kernel.org>

error log for dma_channel_table_init() failure pointed a mere
"initialization failure", which is not very helpful message, so print
additional details like function name and error code.
Signed-off-by: Vinod Koul <vkoul@kernel.org>

We call dma_device_put() and module_put() after invoking
.device_free_chan_resources callback, but we should also take care of
router devices and invoke this after .route_free callback. So move it
after .route_free
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Don't allocate memory using the devm infrastructure and instead call
kfree with the new dmaengine device_release call back. This ensures
the structures are available until the last reference is dropped.

We also need to ensure we call ioat_shutdown() in ioat_remove() so
that all the channels are quiesced and further transaction fails.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20191216190120.21374-6-logang@deltatee.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Adding a reference count helps drivers to properly implement the unbind
while in use case.

References are taken and put every time a channel is allocated or freed.

Once the final reference is put, the device is removed from the
dma_device_list and a release callback function is called to signal
the driver to free the memory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-5-logang@deltatee.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

So it can be called by a release function which is needed higher up in
the code. No functional changes intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-4-logang@deltatee.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The module reference is taken to ensure the callbacks still exist
when they are called. If the channel holds the last reference to the
module, the module can disappear before device_free_chan_resources() is
called and would cause a call into free'd memory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-3-logang@deltatee.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

dma_chan_to_owner() dereferences the driver from the struct device to
obtain the owner and call module_[get|put](). However, if the backing
device is unbound before the dma_device is unregistered, the driver
will be cleared and this will cause a NULL pointer dereference.

Instead, store a pointer to the owner module in the dma_device struct
so the module reference can be properly put when the channel is put, even
if the backing device was destroyed first.

This change helps to support a safer unbind of DMA engines.
If the dma_device is unregistered in the driver's remove function,
there's no guarantee that there are no existing clients and a users
action may trigger the WARN_ONCE in dma_async_device_unregister()
which is unlikely to leave the system in a consistent state.
Instead, a better approach is to allow the backing driver to go away
and fail any subsequent requests to it.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-2-logang@deltatee.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add support for probing the dma-jz4780 driver on the X1830 Soc.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/1576591140-125668-4-git-send-email-zhouyanjie@wanyeetech.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add the dmaengine bindings for the X1830 Soc from Ingenic.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/1576591140-125668-3-git-send-email-zhouyanjie@wanyeetech.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Our platforms(such as LS1021A, LS1012A, LS1043A, LS1046A, LS1028A) with
below registers(CHCFG0 - CHCFG15) of eDMA as follows:
*-----------------------------------------------------------*
|     Offset   |	OTHERS			|		LS1028A			|
|--------------|--------------------|-----------------------|
|     0x0      |        CHCFG0      |           CHCFG3      |
|--------------|--------------------|-----------------------|
|     0x1      |        CHCFG1      |           CHCFG2      |
|--------------|--------------------|-----------------------|
|     0x2      |        CHCFG2      |           CHCFG1      |
|--------------|--------------------|-----------------------|
|     0x3      |        CHCFG3      |           CHCFG0      |
|--------------|--------------------|-----------------------|
|     ...      |        ......      |           ......      |
|--------------|--------------------|-----------------------|
|     0xC      |        CHCFG12     |           CHCFG15     |
|--------------|--------------------|-----------------------|
|     0xD      |        CHCFG13     |           CHCFG14     |
|--------------|--------------------|-----------------------|
|     0xE      |        CHCFG14     |           CHCFG13     |
|--------------|--------------------|-----------------------|
|     0xF      |        CHCFG15     |           CHCFG12     |
*-----------------------------------------------------------*

This patch is to improve edma driver to fit LS1028A platform.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/20191212033714.4090-1-peng.ma@nxp.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

QORIQ LS1028A soc used fsl,vf610-edma, but it has a little bit different
from others, so add new compatible to distinguish them.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20191212033714.4090-3-peng.ma@nxp.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: 2a03c131 ("dmaengine: ti: edma: add missed operations")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212114622.127322-1-weiyongjun1@huawei.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The driver misses checking the result of devm_regmap_init_mmio().
Add a check to fix it.

Fixes: fc15be39 ("dmaengine: axi-dmac: add regmap support")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191209085711.16001-1-hslester96@gmail.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191206132435.29139-1-geert+renesas@glider.beSigned-off-by: Vinod Koul <vkoul@kernel.org>

It has turned out that it's in general a good idea for dmaengines to allow
DMA requests during the entire dpm_suspend() phase. Therefore, convert the
pl330 driver into using SET_LATE_SYSTEM_SLEEP_PM_OPS.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20191205143746.24873-3-ulf.hansson@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Let's drop the boilerplate code in the system suspend/resume callbacks and
convert to use pm_runtime_force_suspend|resume(). This change also has a
nice side effect, as pm_runtime_force_resume() may decide to leave the
device in low power state, when that is feasible, thus avoiding to waste
both time and energy during system resume.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20191205143746.24873-2-ulf.hansson@linaro.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Document support for the system DMA controller in the Renesas R-Car
M3-W+ (R8A77961) SoC.

No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191205133736.5934-1-geert+renesas@glider.beSigned-off-by: Vinod Koul <vkoul@kernel.org>

The driver forgets to call pm_runtime_disable and pm_runtime_put_sync in
probe failure and remove.
Add the calls and modify probe failure handling to fix it.

To simplify the fix, the patch adjusts the calling order and merges checks
for devm_kcalloc.

Fixes: 2b6b3b74 ("ARM/dmaengine: edma: Merge the two drivers under drivers/dma/")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191124052855.6472-1-hslester96@gmail.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Pull networking fixes from David Miller:

 1) More jumbo frame fixes in r8169, from Heiner Kallweit.

 2) Fix bpf build in minimal configuration, from Alexei Starovoitov.

 3) Use after free in slcan driver, from Jouni Hogander.

 4) Flower classifier port ranges don't work properly in the HW offload
    case, from Yoshiki Komachi.

 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.

 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.

 7) Fix flow dissection in dsa TX path, from Alexander Lobakin.

 8) Stale syncookie timestampe fixes from Guillaume Nault.

[ Did an evil merge to silence a warning introduced by this pull - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  r8169: fix rtl_hw_jumbo_disable for RTL8168evl
  net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
  r8169: add missing RX enabling for WoL on RTL8125
  vhost/vsock: accept only packets with the right dst_cid
  net: phy: dp83867: fix hfs boot in rgmii mode
  net: ethernet: ti: cpsw: fix extra rx interrupt
  inet: protect against too small mtu values.
  gre: refetch erspan header from skb->data after pskb_may_pull()
  pppoe: remove redundant BUG_ON() check in pppoe_pernet
  tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
  tcp: tighten acceptance of ACKs not matching a child socket
  tcp: fix rejected syncookies due to stale timestamps
  lpc_eth: kernel BUG on remove
  tcp: md5: fix potential overestimation of TCP option space
  net: sched: allow indirect blocks to bind to clsact in TC
  net: core: rename indirect block ingress cb function
  net-sysfs: Call dev_hold always in netdev_queue_add_kobject
  net: dsa: fix flow dissection on Tx path
  net/tls: Fix return values to avoid ENOTSUPP
  net: avoid an indirect call in ____sys_recvmsg()
  ...

Pull more SCSI updates from James Bottomley:
 "Eleven patches, all in drivers (no core changes) that are either minor
  cleanups or small fixes.

  They were late arriving, but still safe for -rc1"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
  scsi: megaraid_sas: Make poll_aen_lock static
  scsi: sd_zbc: Improve report zones error printout
  scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
  scsi: qla2xxx: unregister ports after GPN_FT failure
  scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
  scsi: pm80xx: Remove unused include of linux/version.h
  scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
  scsi: scsi_transport_sas: Fix memory leak when removing devices
  scsi: lpfc: size cpu map by last cpu id set
  scsi: ibmvscsi_tgt: Remove unneeded variable rc

Pull cifs fixes from Steve French:
 "Nine cifs/smb3 fixes:

   - one fix for stable (oops during oplock break)

   - two timestamp fixes including important one for updating mtime at
     close to avoid stale metadata caching issue on dirty files (also
     improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
     wire)

   - two fixes for "modefromsid" mount option for file create (now
     allows mode bits to be set more atomically and accurately on create
     by adding "sd_context" on create when modefromsid specified on
     mount)

   - two fixes for multichannel found in testing this week against
     different servers

   - two small cleanup patches"

* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: improve check for when we send the security descriptor context on create
  smb3: fix mode passed in on create for modetosid mount option
  cifs: fix possible uninitialized access and race on iface_list
  cifs: Fix lookup of SMB connections on multichannel
  smb3: query attributes on file close
  smb3: remove unused flag passed into close functions
  cifs: remove redundant assignment to pointer pneg_ctxt
  fs: cifs: Fix atime update check vs mtime
  CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks

Pull misc vfs cleanups from Al Viro:
 "No common topic, just three cleanups".

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  make __d_alloc() static
  fs/namespace: add __user to open_tree and move_mount syscalls
  fs/fnctl: fix missing __user in fcntl_rw_hint()

Pull NTB update from Jon Mason:
 "Just a simple patch to add a new Hygon Device ID to the AMD NTB device
  driver"

* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
  NTB: Add Hygon Device ID