- 11 Jan, 2013 10 commits
-
-
Will Deacon authored
commit 304ef4e8 upstream. To allow debuggers to unwind through signal frames, we create a fake stack unwinding prologue containing the link register and frame pointer of the interrupted context. The signal frame is then offset by 16 bytes to make room for the two saved registers which are pushed onto the frame of the *interrupted* context, rather than placed directly above the signal stack. This doesn't work when an alternative signal stack is set up for a SEGV handler, which is raised in response to RLIMIT_STACK being reached. In this case, we try to push the unwinding prologue onto the full stack and subsequently take a fault which we fail to resolve, causing setup_return to return -EFAULT and handle_signal to force_sigsegv on the current task. This patch fixes the problem by including the unwinding prologue as part of the rt_sigframe definition, which is populated during setup_sigframe, ensuring that it always ends up on the signal stack. Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Catalin Marinas authored
commit 33eaa58f upstream. The AArch64 Linux port relies on the mm code to wrprotect clean ptes. This however is not the case with newly created ptes and PAGE_SHARED(_EXEC) is writable but !dirty. Signed-off-by:
-
Kees Cook authored
commit b66c5984 upstream. If a series of scripts are executed, each triggering module loading via unprintable bytes in the script header, kernel stack contents can leak into the command line. Normally execution of binfmt_script and binfmt_misc happens recursively. However, when modules are enabled, and unprintable bytes exist in the bprm->buf, execution will restart after attempting to load matching binfmt modules. Unfortunately, the logic in binfmt_script and binfmt_misc does not expect to get restarted. They leave bprm->interp pointing to their local stack. This means on restart bprm->interp is left pointing into unused stack memory which can then be copied into the userspace argv areas. After additional study, it seems that both recursion and restart remains the desirable way to handle exec with scripts, misc, and modules. As such, we need to protect the changes to interp. This changes the logic to require allocation for any changes to the bprm->interp. To avoid adding a new kmalloc to every exec, the default value is left as-is. Only when passing through binfmt_script or binfmt_misc does an allocation take place. For a proof of concept, see DoTest.sh from: http://www.halfdog.net/Security/2012/LinuxKernelBinfmtScriptStackDataDisclosure/Signed-off-by:
Kees Cook <keescook@chromium.org> Cc: halfdog <me@halfdog.net> Cc: P J P <ppandit@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Robin Holt authored
commit 891348ca upstream. We found a user code which was raising a divide-by-zero trap. That trap would lead to XPC connections between system-partitions being torn down due to the die_chain notifier callouts it received. This also revealed a different issue where multiple callers into xpc_die_deactivate() would all attempt to do the disconnect in parallel which would sometimes lock up but often overwhelm the console on very large machines as each would print at least one line of output at the end of the deactivate. I reviewed all the users of the die_chain notifier and changed the code to ignore the notifier callouts for reasons which will not actually lead to a system to continue on to call die(). [akpm@linux-foundation.org: fix ia64] Signed-off-by:
Robin Holt <holt@sgi.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Alan Cox authored
commit cdc87c5a upstream. TEST_ALPHA() is broken and always returns 0. [akpm@linux-foundation.org: return false for '@' as well, per Bjorn] Signed-off-by:
Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Felix Fietkau authored
commit 78f18df4 upstream. ieee80211_free_txskb() needs to be used instead of dev_kfree_skb_any for tx packets passed to the driver from mac80211 Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Larry Finger authored
commit 576d28a7 upstream. Recent versions of udev cause synchronous firmware loading from the probe routine to fail because the request to user space times out. The original fix for b43legacy (commit a3ea2c76) moved the firmware load from the probe routine to a work queue, but it still used synchronous firmware loading. This method is OK when b43legacy is built as a module; however, it fails when the driver is compiled into the kernel. This version changes the code to load the initial firmware file using request_firmware_nowait(). A completion event is used to hold the work queue until that file is available. The remaining firmware files are read synchronously. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Chuansheng Liu authored
commit bd9eb7fb upstream. There is one race that both request_firmware() with the same firmware name. The race scenerio is as below: CPU1 CPU2 request_firmware() --> _request_firmware_load() return err another request_firmware() is coming --> _request_firmware_cleanup is called --> _request_firmware_prepare --> release_firmware ---> fw_lookup_and_allocate_buf --> spin_lock(&fwc->lock) ... __fw_lookup_buf() return true fw_free_buf() will be called --> ... kref_put --> decrease the refcount to 0 kref_get(&tmp->ref) ==> it will trigger warning due to refcount == 0 __fw_free_buf() --> ... spin_unlock(&fwc->lock) spin_lock(&fwc->lock) list_del(&buf->list) spin_unlock(&fwc->lock) kfree(buf) After that, the freed buf will be used. The key race is decreasing refcount to 0 and list_del is not protected together by fwc->lock, and it is possible another thread try to get it between refcount==0 and list_del. Fix it here to protect it together. Acked-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
liu chuansheng <chuansheng.liu@intel.com> Signed-off-by:
-
Chuansheng Liu authored
commit ce2fcbd9 upstream. There is a race as below when calling request_firmware(): CPU1 CPU2 write 0 > loading mutex_lock(&fw_lock) ... set_bit FW_STATUS_DONE class_timeout is coming set_bit FW_STATUS_ABORT complete_all &completion ... mutex_unlock(&fw_lock) In this time, the bit FW_STATUS_DONE and FW_STATUS_ABORT are set, and request_firmware() will return failure due to condition in _request_firmware_load(): if (!buf->size || test_bit(FW_STATUS_ABORT, &buf->status)) retval = -ENOENT; But from the above scenerio, it should be a successful requesting. So we need judge if the bit FW_STATUS_DONE is already set before calling fw_load_abort() in timeout function. As Ming's proposal, we need change the timer into sched_work to benefit from using &fw_lock mutex also. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit f8e8f97c ] Dmitry Kravkov reported packet drops for GRE packets since GRO support was added. There is a race in gro_cell_poll() because we call napi_complete() without any synchronization with a concurrent gro_cells_receive() Once bug was triggered, we queued packets but did not schedule NAPI poll. We can fix this issue using the spinlock protected the napi_skbs queue, as we have to hold it to perform skb dequeue anyway. As we open-code skb_dequeue(), we no longer need to mask IRQS, as both producer and consumer run under BH context. Bug added in commit c9e6bc64 (net: add gro_cells infrastructure) Reported-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Tested-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
- 17 Dec, 2012 28 commits
-
-
Greg Kroah-Hartman authored
-
Kevin McKinney authored
commit 4f29ef05 upstream. This patch adds two new products and modifies the device id table to include them. In addition, product of 0xbccd - BCM_USB_PRODUCT_ID_SM250 is removed because Beceem, ZTE, Sprint use this id for block devices. Reported-by:
Muhammad Minhazul Haque <mdminhazulhaque@gmail.com> Signed-off-by:
Kevin McKinney <klmckinney1@gmail.com> Signed-off-by:
-
Eric Dumazet authored
commit 878d7439 upstream. Commit 29c00b4a (rcu: Add event-tracing for RCU callback invocation) added a regression in rcu_do_batch() Under stress, RCU is supposed to allow to process all items in queue, instead of a batch of 10 items (blimit), but an integer overflow makes the effective limit being 1. So, unless there is frequent idle periods (during which RCU ignores batch limits), RCU can be forced into a state where it cannot keep up with the callback-generation rate, eventually resulting in OOM. This commit therefore converts a few variables in rcu_do_batch() from int to long to fix this problem, along with the module parameters controlling the batch limits. Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by:
-
Alan Stern authored
commit 2656a9ab upstream. This patch (as1632b) fixes a bug in ehci-hcd. The USB core uses urb->hcpriv to determine whether or not an URB is active; host controller drivers are supposed to set this pointer to a non-NULL value when an URB is queued. However ehci-hcd sets it to NULL for isochronous URBs, which defeats the check in usbcore. In itself this isn't a big deal. But people have recently found that certain sequences of actions will cause the snd-usb-audio driver to reuse URBs without waiting for them to complete. In the absence of proper checking by usbcore, the URBs get added to their endpoint list twice. This leads to list corruption and a system freeze. The patch makes ehci-hcd assign a meaningful value to urb->hcpriv for isochronous URBs. Improving robustness always helps. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Artem S. Tashkinov <t.artem@lycos.com> Reported-by:
Christof Meerwald <cmeerw@cmeerw.org> Signed-off-by:
-
Zheng Liu authored
commit 12f8f74b upstream. Recently I build perf and get a build error on builtin-test.c. The error is as following: $ make CC perf.o CC builtin-test.o cc1: warnings being treated as errors builtin-test.c: In function ‘sched__get_first_possible_cpu’: builtin-test.c:977: warning: implicit declaration of function ‘CPU_ALLOC’ builtin-test.c:977: warning: nested extern declaration of ‘CPU_ALLOC’ builtin-test.c:977: warning: assignment makes pointer from integer without a cast builtin-test.c:978: warning: implicit declaration of function ‘CPU_ALLOC_SIZE’ builtin-test.c:978: warning: nested extern declaration of ‘CPU_ALLOC_SIZE’ builtin-test.c:979: warning: implicit declaration of function ‘CPU_ZERO_S’ builtin-test.c:979: warning: nested extern declaration of ‘CPU_ZERO_S’ builtin-test.c:982: warning: implicit declaration of function ‘CPU_FREE’ builtin-test.c:982: warning: nested extern declaration of ‘CPU_FREE’ builtin-test.c:992: warning: implicit declaration of function ‘CPU_ISSET_S’ builtin-test.c:992: warning: nested extern declaration of ‘CPU_ISSET_S’ builtin-test.c:998: warning: implicit declaration of function ‘CPU_CLR_S’ builtin-test.c:998: warning: nested extern declaration of ‘CPU_CLR_S’ make: *** [builtin-test.o] Error 1 This problem is introduced in 3e7c439a. CPU_ALLOC and related macros are missing in sched__get_first_possible_cpu function. In 54489c18, commiter mentioned that CPU_ALLOC has been removed. So CPU_ALLOC calls in this function are removed to let perf to be built. Signed-off-by:
Vinson Lee <vlee@twitter.com> Signed-off-by:
Zheng Liu <wenqing.lz@taobao.com> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Vinson Lee <vlee@twitter.com> Cc: Zheng Liu <wenqing.lz@taobao.com> Link: http://lkml.kernel.org/r/1352422726-31114-1-git-send-email-vlee@twitter.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Dan Williams authored
commit ba2d8ce9 upstream. Some devices (ex Nokia C7) simply don't respond at all when data is sent to some of their USB interfaces. The data gets stuck in the TTYs queue and sits there until close(2), which them blocks because closing_wait defaults to 30 seconds (even though the fd is O_NONBLOCK). This is rarely desired. Implement the standard mechanism to adjust closing_wait and let applications handle it how they want to. See also 02303f73 for usb_wwan.c. Signed-off-by:
Dan Williams <dcbw@redhat.com> Acked-by:
Oliver Neukum <oneukum@suse.de> Tested-by:
Aleksander Morgado <aleksander@gnu.org> Signed-off-by:
-
Steven Rostedt authored
commit 9366c1ba upstream. The function rb_check_pages() was added to make sure the ring buffer's pages were sane. This check is done when the ring buffer size is modified as well as when the iterator is released (closing the "trace" file), as that was considered a non fast path and a good place to do a sanity check. The problem is that the check does not have any locks around it. If one process were to read the trace file, and another were to read the raw binary file, the check could happen while the reader is reading the file. The issues with this is that the check requires to clear the HEAD page before doing the full check and it restores it afterward. But readers require the HEAD page to exist before it can read the buffer, otherwise it gives a nasty warning and disables the buffer. By adding the reader lock around the check, this keeps the race from happening. Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt authored
commit 54f7be5b upstream. The function rb_set_head_page() searches the list of ring buffer pages for a the page that has the HEAD page flag set. If it does not find it, it will do a WARN_ON(), disable the ring buffer and return NULL, as this should never happen. But if this bug happens to happen, not all callers of this function can handle a NULL pointer being returned from it. That needs to be fixed. Signed-off-by:
-
Dan Carpenter authored
commit 70f77b3f upstream. There is a typo here where '&' is used instead of '|' and it turns the statement into a noop. The original code is equivalent to: iter->flags &= ~((1 << 2) & (1 << 4)); Link: http://lkml.kernel.org/r/20120609161027.GD6488@elgon.mountainSigned-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Sarah Sharp authored
commit bba18e33 upstream. Ali reports that plugging a device into the Fresco Logic xHCI host with PCI device ID 1400 produces an IRQ error: do_IRQ: 3.176 No irq handler for vector (irq -1) Other early Fresco Logic host revisions don't support MSI, even though their PCI config space claims they do. Extend the quirk to disabling MSI to this chipset revision. Also enable the short transfer quirk, since it's likely this revision also has that quirk, and it should be harmless to enable. 04:00.0 0c03: 1b73:1400 (rev 01) (prog-if 30 [XHCI]) Subsystem: 1d5c:1000 Physical Slot: 3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 51 Region 0: Memory at d4600000 (32-bit, non-prefetchable) [size=64K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000feeff00c Data: 41b1 Capabilities: [80] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <2us, L1 <32us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Kernel driver in use: xhci_hcd This patch should be backported to stable kernels as old as 2.6.36, that contain the commit f5182b41 "xhci: Disable MSI for some Fresco Logic hosts." Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by:
A Sh <smr.ash1991@gmail.com> Tested-by:
-
Alan Stern authored
commit 50ce5c06 upstream. This patch (as1636) is a partial workaround for a hardware bug affecting OHCI controllers by NVIDIA at least, maybe others too. When the controller retires a Transfer Descriptor, it is supposed to add the TD onto the Done Queue. But sometimes this doesn't happen, with the result that ohci-hcd never realizes the corresponding transfer has finished. Symptoms can vary; a typical result is that USB audio stops working after a while. The patch works around the problem by recognizing that TDs are always processed in order. Therefore, if a later TD is found on the Done Queue than all the earlier TDs for the same endpoint must be finished as well. Unfortunately this won't solve the problem in cases where the missing TD is the last one in the endpoint's queue. A complete fix would require a signficant amount of change to the driver. Signed-off-by:
-
Lan Tianyu authored
commit d0c2ce16 upstream. The ACPI video driver can't control backlight correctly on Asus UL30VT. Vendor driver (asus-laptop) can work. This patch is to add "Asus UL30VT" to ACPI video detect blacklist in order to use asus-laptop for video control on the "Asus UL30VT" rather than ACPI video driver. References: https://bugzilla.kernel.org/show_bug.cgi?id=32592Reported-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
Lan Tianyu <tianyu.lan@intel.com> Signed-off-by:
-
Zhang Rui authored
commit 129ff8f8 upstream. Or else the laptop will boot with a dimmed screen. References: https://bugzilla.kernel.org/show_bug.cgi?id=51141Tested-by:
Stefan Nagy <public@stefan-nagy.at> Signed-off-by:
Zhang Rui <rui.zhang@intel.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit a6b5e88c upstream. During resume from system suspend the 'data' field of struct pnp_dev in pnpacpi_set_resources() may be a stale pointer, due to removal of the associated ACPI device node object in the previous suspend-resume cycle. This happens, for example, if a dockable machine is booted in the docking station and then suspended and resumed and suspended again. If that happens, pnpacpi_build_resource_template() called from pnpacpi_set_resources() attempts to use that pointer and crashes. However, pnpacpi_set_resources() actually checks the device's ACPI handle, attempts to find the ACPI device node object attached to it and returns an error code if that fails, so in fact it knows what the correct value of dev->data should be. Use this observation to update dev->data with the correct value if necessary and dump a call trace if that's the case (once). We still need to fix the root cause of this issue, but preventing systems from crashing because of it is an improvement too. Reported-and-tested-by:
Zdenek Kabelac <zdenek.kabelac@gmail.com> References: https://bugzilla.kernel.org/show_bug.cgi?id=51071Signed-off-by:
-
Lan Tianyu authored
commit 876ab790 upstream. Sony Vaio VPCEB1S1E does not resume correctly without acpi_sleep=nonvs, so add it to the ACPI sleep blacklist. References: https://bugzilla.kernel.org/show_bug.cgi?id=48781Reported-by:
Sébastien Wilmet <swilmet@gnome.org> Signed-off-by:
-
Kamil Iskra authored
commit 4000e626 upstream. Add a quirk to correctly report battery capacity on 2010 and 2011 Lenovo Thinkpad models. The affected models that I tested (x201, t410, t410s, and x220) exhibit a problem where, when battery capacity reporting unit is mAh, the values being reported are wrong. Pre-2010 and 2012 models appear to always report in mWh and are thus unaffected. Also, in mid-2012 Lenovo issued a BIOS update for the 2011 models that fixes the issue (tested on x220 with a post-1.29 BIOS). No such update is available for the 2010 models, so those still need this patch. Problem description: for some reason, the affected Thinkpads switch the reporting unit between mAh and mWh; generally, mAh is used when a laptop is plugged in and mWh when it's unplugged, although a suspend/resume or rmmod/modprobe is needed for the switch to take effect. The values reported in mAh are *always* wrong. This does not appear to be a kernel regression; I believe that the values were never reported correctly. I tested back to kernel 2.6.34, with multiple machines and BIOS versions. Simply plugging a laptop into mains before turning it on is enough to reproduce the problem. Here's a sample /proc/acpi/battery/BAT0/info from Thinkpad x220 (before a BIOS update) with a 4-cell battery: present: yes design capacity: 2886 mAh last full capacity: 2909 mAh battery technology: rechargeable design voltage: 14800 mV design capacity warning: 145 mAh design capacity low: 13 mAh cycle count: 0 capacity granularity 1: 1 mAh capacity granularity 2: 1 mAh model number: 42T4899 serial number: 21064 battery type: LION OEM info: SANYO Once the laptop switches the unit to mWh (unplug from mains, suspend, resume), the output changes to: present: yes design capacity: 28860 mWh last full capacity: 29090 mWh battery technology: rechargeable design voltage: 14800 mV design capacity warning: 1454 mWh design capacity low: 200 mWh cycle count: 0 capacity granularity 1: 1 mWh capacity granularity 2: 1 mWh model number: 42T4899 serial number: 21064 battery type: LION OEM info: SANYO Can you see how the values for "design capacity", etc., differ by a factor of 10 instead of 14.8 (the design voltage of this battery)? On the battery itself it says: 14.8V, 1.95Ah, 29Wh, so clearly the values reported in mWh are correct and the ones in mAh are not. My guess is that this problem has been around ever since those machines were released, but because the most common Thinkpad batteries are rated at 10.8V, the error (8%) is small enough that it simply hasn't been noticed or at least nobody could be bothered to look into it. My patch works around the problem by adjusting the incorrectly reported mAh values by "10000 / design_voltage". The patch also has code to figure out if it should be activated or not. It only activates on Lenovo Thinkpads, only when the unit is mAh, and, as an extra precaution, only when the battery capacity reported through ACPI does not match what is reported through DMI (I've never encountered a machine where the first two conditions would be true but the last would not, but better safe than sorry). I've been using this patch for close to a year on several systems without any problems. References: https://bugzilla.kernel.org/show_bug.cgi?id=41062Acked-by:
Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by:
-
Greg Kroah-Hartman authored
commit fb37ef98 upstream. As reported https://bugzilla.kernel.org/show_bug.cgi?id=51031, the UAS driver causes problems and has been asked to be not built into any of the major distributions. To prevent users from running into problems with it, and for distros that were not notified, just mark the whole thing as broken. Acked-by:
-
Markus Becker authored
commit 356fe44f upstream. Signed-off-by:
Markus Becker <mab@comnets.uni-bremen.de> Signed-off-by:
-
Peter Korsgaard authored
commit 1a88d5ee upstream. BeagleBone A5+ devices ended up getting shipped with the 'BeagleBone/XDS100V2' product string, and not XDS100 like it was agreed, so adjust the quirk to match. For details, see the thread on the beagle list: https://groups.google.com/forum/#!msg/beagleboard/zrFPew9_Wvo/ibWr1-eE8JwJSigned-off-by:
Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by:
-
Martin Teichmann authored
commit d7e14b37 upstream. The Newport AGILIS model AG-UC8 compact piezo motor controller (http://search.newport.com/?q=*&x2=sku&q2=AG-UC8) is yet another device using an FTDI USB-to-serial chip. It works fine with the ftdi_sio driver when adding options ftdi-sio product=0x3000 vendor=0x104d to modprobe.d. udevadm reports "Newport" as the manufacturer, and "Agilis" as the product name. Signed-off-by:
Martin Teichmann <lkb.teichmann@gmail.com> Signed-off-by:
-
Bjørn Mork authored
commit f36446cf upstream. The Huawei E173 will normally appear as 12d1:1436 in Linux. But the modem has another mode with different device ID and a slightly different set of descriptors. This is the mode used by Windows like this: 3Modem: USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000 Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001 Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002 PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003 All interfaces have the same ff/ff/ff class codes in this mode. Blacklisting the network interface to allow it to be picked up by the network driver. Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
li.rui27@zte.com.cn authored
commit 31b6a104 upstream. Signed-off-by:
Rui li <li.rui27@zte.com.cn> Signed-off-by:
-
Jan Beulich authored
commit 6acf5a8c upstream. HPET_TN_FSB is not a proper mask bit; it merely toggles between MSI and legacy interrupt delivery. The proper mask bit is HPET_TN_ENABLE, so use both bits when (un)masking the interrupt. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Link: http://lkml.kernel.org/r/5093E09002000078000A60E6@nat28.tlf.novell.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Rene Buergel authored
commit 9db72fe6 upstream. This fixes an error during modpost, when ezusb is built into the kernel while USB is built as module. Signed-off-by:
René Bürgel <rene.buergel@sohard.de> Cc: Jeff Mahoney <jeffm@suse.com> Signed-off-by:
-
Dan Carpenter authored
[Not needed in 3.8 or newer as this driver is removed there. - gregkh] We get this from user space and nothing has been done to ensure that these strings are NUL terminated. Reported-by:
Chen Gang <gang.chen@asianux.com> Signed-off-by:
-
Boris Ostrovsky authored
commit 22e32f4f upstream. Add family 16h PCI ID to AMD's power driver to allow it report power consumption on these processors. Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@amd.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Linus Walleij authored
commit 2630b17b upstream. This fixes a bit error in the U8500 clock implementation: the unused p2_pclk12 registered at bit 12 in periphereral group 6 was defined as using bit 11 rather than bit 12. When walking over and disabling the unused clocks in the tree at late init time, p2_pclk12 was disabled, by effectively clearing the but for p2_pclk11 instead of bit 12 as it should have, thus disabling gpio block 6 and 7. Reported-by:
Lee Jones <lee.jones@linaro.org> Acked-by:
Ulf Hansson <ulf.hansson@linaro.org> Cc: Philippe Begnic <philippe.begnic@st.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Mike Turquette <mturquette@linaro.org> Signed-off-by:
-
Marek Szyprowski authored
commit 387870f2 upstream. dmapool always calls dma_alloc_coherent() with GFP_ATOMIC flag, regardless the flags provided by the caller. This causes excessive pruning of emergency memory pools without any good reason. Additionaly, on ARM architecture any driver which is using dmapools will sooner or later trigger the following error: "ERROR: 256 KiB atomic DMA coherent pool is too small! Please increase it with coherent_pool= kernel parameter!". Increasing the coherent pool size usually doesn't help much and only delays such error, because all GFP_ATOMIC DMA allocations are always served from the special, very limited memory pool. This patch changes the dmapool code to correctly use gfp flags provided by the dmapool caller. Reported-by:
Soeren Moch <smoch@web.de> Reported-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Tested-by:
Andrew Lunn <andrew@lunn.ch> Tested-by:
-
- 11 Dec, 2012 2 commits
-
-
Linus Torvalds authored
-
Florian Fainelli authored
The matrix-keymap module is currently lacking a proper module license, add one so we don't have this module tainting the entire kernel. This issue has been present since commit 1932811f ("Input: matrix-keymap - uninline and prepare for device tree support") Signed-off-by:
Florian Fainelli <florian@openwrt.org> CC: stable@vger.kernel.org # v3.5+ Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
