- 23 Sep, 2009 40 commits
-
-
Chris Verges authored
Add support for the Philips/NXP PCF2123 RTC. Signed-off: Chris Verges <chrisv@cyberswitching.com> Tested-by:
Chris Verges <chrisv@cyberswitching.com> Signed-off: Christian Pellegrin <chripell@fsfe.org> Tested-by:
Christian Pellegrin <chripell@fsfe.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
David Brownell authored
Support two new half-duplex SPI implementation restrictions, for links that talk to TX-only or RX-only devices. (Existing half-duplex flavors support both transfer directions, just not at the same time.) Move spi_async() into the spi.c core, and stop inlining it. Then make that function perform error checks and reject messages that demand more than the underlying controller can support. Based on a patch from Marek Szyprowski which did this only for the bitbanged GPIO driver. Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Syed Rafiuddin authored
tAdd adds McSPI support for OMAP4430 SDP platform. All the base addresses are changed between OMAP1/2/3 and OMAP4. The fields of the resource structures are filled at runtime to have McSPI support on OMAP4. Signed-off-by:
Syed Rafiuddin <rafiuddin.syed@ti.com> Acked-by:
Kevin Hilman <khilman@deeprootsystems.com> Acked-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by:
-
Tero Kristo authored
Previous restore was lazy and only restored CHxCONF when it was needed by a specific chip select. This could cause occasional errors on an SPI bus where multiple chip selects are in use. Signed-off-by:
Tero Kristo <tero.kristo@nokia.com> Signed-off-by:
-
Hemanth V authored
Add context save/restore feature to McSPI driver. Signed-off-by:
Hemanth V <hemanthv@ti.com> Reviewed-by:
Aaro Koskinen <Aaro.Koskinen@nokia.com> Signed-off-by:
-
dmitry pervushin authored
Add SPI driver for Freescale STMP 3xxx-based boards [dbrownell@users.sourceforge.net: cleanup sequence, spi_unregister_master] Signed-off-by:
dmitry pervushin <dpervushin@embeddedalley.com> Signed-off-by:
-
Ben Dooks authored
With the update to the spi_bitbang driver, the transfer setup code is being called more often, and thus is often re-doing calculations that have been done before. The SPI layer allows our driver to add its own data to each device so add a result cache to each device. This should also remove the problem where we where directly setting up registers in the setup call which meant we might overwrite the state of an extant transfer., Signed-off-by:
Ben Dooks <ben@simtec.co.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
Ben Dooks authored
Change the spi_s3c24xx driver to use dev_pm_ops to avoid the following warning during probe: Platform driver 's3c2410-spi' needs updating - please use dev_pm_ops Signed-off-by:
-
Ben Dooks authored
Change the use of (res->end - res->start) to use resource_size() to get the size of the resource. Signed-off-by; Ben Dooks <ben@simtec.co.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
Ben Dooks authored
The driver includes <asm/io.h> where it should be including <linux/io.h> and also includes <mach/hardware.h> and <asm/dma.h> without using anything from these. Signed-off-by:
-
Ben Dooks authored
Fix spelling of `automatically' in Documentation/spi/spi-summary. Signed-off-by:
-
Antonio Ospite authored
Register pxa2xx_spi earlier so it can be used with cpufreq Signed-off-by:
Daniel Ribeiro <drwyrm@gmail.com> Acked-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Daniel Ribeiro <drwyrm@gmail.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by:
-
Anton Vorontsov authored
This makes it consistent with other buses (platform, i2c, vio, ...). I'm not sure why we use the prefixes, but there must be a reason. This was easy enough to do it, and I did it. Signed-off-by:
Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Jean Delvare <khali@linux-fr.org> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Samuel Ortiz <sameo@openedhand.com> Cc: "John W. Linville" <linville@tuxdriver.com> Acked-by:
Mike Frysinger <vapier.adi@gmail.com> Signed-off-by:
-
Anton Vorontsov authored
Make the code a little bit nicer, and shorter. Signed-off-by:
-
Anton Vorontsov authored
Make the code a little bit nicer, and shorter. Signed-off-by:
Marc Pignat <marc.pignat@hevs.ch> Signed-off-by:
-
Anton Vorontsov authored
The alias isn't needed any longer since the m25p80 driver converted to the module device table matching. Signed-off-by:
-
Anton Vorontsov authored
With this patch spi drivers can use standard spi_driver.id_table and MODULE_DEVICE_TABLE() mechanisms to bind against the devices. Just like we do with I2C drivers. This is useful when a single driver supports several variants of devices but it is not possible to detect them in run-time (like non-JEDEC chips probing in drivers/mtd/devices/m25p80.c), and when platform_data usage is overkill. This patch also makes life a lot easier on OpenFirmware platforms, since with OF we extensively use proper device IDs in modaliases. Signed-off-by:
-
Sascha Hauer authored
This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Tested-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by:
David Brownell <david-b@pacbell.net> Cc: Andrea Paterniani <a.paterniani@swapp-eng.it> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by:
-
linus.walleij@stericsson.com authored
This makes the PL022 driver a default choice for any RealView and Versatile boards plus the integrator IMPD1 which all contain the PL022 PrimeCell. This will make it a default choice if and only if a user selects SPI support for their board. Signed-off-by:
Linus Walleij <linus.walleij@stericsson.com> Signed-off-by:
-
Randy Dunlap authored
Add missing kernel-doc notation in spi.h for struct spi_master: Warning(include/linux/spi/spi.h:289): No description found for parameter 'mode_bits' Warning(include/linux/spi/spi.h:289): No description found for parameter 'flags' Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Acked-by:
-
Steven A. Falco authored
This adds a SPI driver for the SPI controller found in the IBM/AMCC 4xx PowerPC's. Signed-off-by:
Stefan Roese <sr@denx.de> Signed-off-by:
Wolfgang Ocker <weo@reccoware.de> Acked-by:
Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by:
Steven A. Falco <sfalco@harris.com> Signed-off-by:
-
Jouni Hogander authored
Convert bit shifted values into BIT format Signed-off-by:
Jouni Hogander <jouni.hogander@nokia.com> Signed-off-by:
-
Sascha Hauer authored
This driver is in a non working state at the moment and will be replaced by a bitbang driver which can also handle the newer i.MX variants Signed-off-by:
Andrea Paterniani <a.paterniani@swapp-eng.it> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
We want to check for s_inode's existence, not inode's one (inode is always valid in this function). This takes care of the following entry from Dan's list: fs/ncpfs/ioctl.c +445 __ncp_ioctl(180) warning: variable derefenced before check 'inode' Reported-by:
Dan Carpenter <error27@gmail.com> Cc: Julia Lawall <julia@diku.dk> Signed-off-by:
Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Cc: Petr Vandrovec <vandrove@vc.cvut.cz> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Noticed-by:
Joe Perches <joe@perches.com> Cc: Petr Vandrovec <vandrove@vc.cvut.cz> Signed-off-by:
-
Roel Kluin authored
This function uses signed integers for the unix_date and local variables - if a negative number is supplied and the leap-year condition is not met, month will be 0, leading to a later read of day_n[-1] Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz> Signed-off-by:
-
maximilian attems authored
initramfs userspace likes to use this magic number. Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk> Signed-off-by:
maximilian attems <max@stro.at> Signed-off-by:
-
KAMEZAWA Hiroyuki authored
After memory hotplug (or other events in future), kcore size can be modified. To update inode->i_size, we have to know inode/dentry but we can't get it from inside /proc directly. But considerinyg memory hotplug, kcore image is updated only when it's opened. Then, updating inode->i_size at open() is enough. Signed-off-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by:
WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by:
-
KAMEZAWA Hiroyuki authored
Presently the size of /proc/kcore which can be read by 'ls -l' is 0. But it's not the correct value. On x86-64, ls -l shows ... root root 140737486266368 2009-09-17 10:29 /proc/kcore Then, 7FFFFFFE02000. This comes from vmalloc area's size. (*) This shows "core" size, not memory size. This patch shows the size by updating "size" field in struct proc_dir_entry. Later, lookup routine will create inode and fill inode->i_size based on this value. Then, this has a problem. - Once inode is cached, inode->i_size will never be updated. Then, this patch is not memory-hotplug-aware. To update inode->i_size, we have to know dentry or inode. But there is no way to lookup them by inside kernel. Hmmm.... Next patch will try it. Signed-off-by:
-
KAMEZAWA Hiroyuki authored
proc_kcore_init() doesn't check NULL case. fix it and remove unnecessary comments. Signed-off-by:
-
KAMEZAWA Hiroyuki authored
Some archs define MODULED_VADDR/MODULES_END which is not in VMALLOC area. This is handled only in x86-64. This patch make it more generic. And we can use vread/vwrite to access the area. Fix it. Signed-off-by:
-
KAMEZAWA Hiroyuki authored
Benjamin Herrenschmidt <benh@kernel.crashing.org> pointed out that vmemmap range is not included in KCORE_RAM, KCORE_VMALLOC .... This adds KCORE_VMEMMAP if SPARSEMEM_VMEMMAP is used. By this, vmemmap can be readable via /proc/kcore Because it's not vmalloc area, vread/vwrite cannot be used. But the range is static against the memory layout, this patch handles vmemmap area by the same scheme with physical memory. This patch assumes SPARSEMEM_VMEMMAP range is not in VMALLOC range. It's correct now. [akpm@linux-foundation.org: fix typo] Signed-off-by:
-
KAMEZAWA Hiroyuki authored
For /proc/kcore, each arch registers its memory range by kclist_add(). In usual, - range of physical memory - range of vmalloc area - text, etc... are registered but "range of physical memory" has some troubles. It doesn't updated at memory hotplug and it tend to include unnecessary memory holes. Now, /proc/iomem (kernel/resource.c) includes required physical memory range information and it's properly updated at memory hotplug. Then, it's good to avoid using its own code(duplicating information) and to rebuild kclist for physical memory based on /proc/iomem. Signed-off-by:
Jiri Slaby <jirislaby@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: WANG Cong <xiyou.wangcong@gmail.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by:
-
KAMEZAWA Hiroyuki authored
Originally, walk_memory_resource() was introduced to traverse all memory of "System RAM" for detecting memory hotplug/unplug range. For doing so, flags of IORESOUCE_MEM|IORESOURCE_BUSY was used and this was enough for memory hotplug. But for using other purpose, /proc/kcore, this may includes some firmware area marked as IORESOURCE_BUSY | IORESOUCE_MEM. This patch makes the check strict to find out busy "System RAM". Note: PPC64 keeps their own walk_memory_resouce(), which walk through ppc64's lmb informaton. Because old kclist_add() is called per lmb, this patch makes no difference in behavior, finally. And this patch removes CONFIG_MEMORY_HOTPLUG check from this function. Because pfn_valid() just show "there is memmap or not* and cannot be used for "there is physical memory or not", this function is useful in generic to scan physical memory range. Signed-off-by:
-
KAMEZAWA Hiroyuki authored
Some 64bit arch has special segment for mapping kernel text. It should be entried to /proc/kcore in addtion to direct-linear-map, vmalloc area. This patch unifies KCORE_TEXT entry scattered under x86 and ia64. I'm not familiar with other archs (mips has its own even after this patch) but range of [_stext ..._end) is a valid area of text and it's not in direct-map area, defining CONFIG_ARCH_PROC_KCORE_TEXT is only a necessary thing to do. Note: I left mips as it is now. Signed-off-by:
-
KAMEZAWA Hiroyuki authored
For /proc/kcore, vmalloc areas are registered per arch. But, all of them registers same range of [VMALLOC_START...VMALLOC_END) This patch unifies them. By this. archs which have no kclist_add() hooks can see vmalloc area correctly. Signed-off-by:
-
KAMEZAWA Hiroyuki authored
Presently, kclist_add() only eats start address and size as its arguments. Considering to make kclist dynamically reconfigulable, it's necessary to know which kclists are for System RAM and which are not. This patch add kclist types as KCORE_RAM KCORE_VMALLOC KCORE_TEXT KCORE_OTHER This "type" is used in a patch following this for detecting KCORE_RAM. Signed-off-by:
-
KAMEZAWA Hiroyuki authored
This patchset is for /proc/kcore. With this, - many per-arch hooks are removed. - /proc/kcore will know really valid physical memory area. - /proc/kcore will be aware of memory hotplug. - /proc/kcore will be architecture independent i.e. if an arch supports CONFIG_MMU, it can use /proc/kcore. (if the arch uses usual memory layout.) This patch: /proc/kcore uses its own list handling codes. It's better to use generic list codes. No changes in logic. just clean up. Signed-off-by:
-
Stefani Seibold authored
A patch to give a better overview of the userland application stack usage, especially for embedded linux. Currently you are only able to dump the main process/thread stack usage which is showed in /proc/pid/status by the "VmStk" Value. But you get no information about the consumed stack memory of the the threads. There is an enhancement in the /proc/<pid>/{task/*,}/*maps and which marks the vm mapping where the thread stack pointer reside with "[thread stack xxxxxxxx]". xxxxxxxx is the maximum size of stack. This is a value information, because libpthread doesn't set the start of the stack to the top of the mapped area, depending of the pthread usage. A sample output of /proc/<pid>/task/<tid>/maps looks like: 08048000-08049000 r-xp 00000000 03:00 8312 /opt/z 08049000-0804a000 rw-p 00001000 03:00 8312 /opt/z 0804a000-0806b000 rw-p 00000000 00:00 0 [heap] a7d12000-a7d13000 ---p 00000000 00:00 0 a7d13000-a7f13000 rw-p 00000000 00:00 0 [thread stack: 001ff4b4] a7f13000-a7f14000 ---p 00000000 00:00 0 a7f14000-a7f36000 rw-p 00000000 00:00 0 a7f36000-a8069000 r-xp 00000000 03:00 4222 /lib/libc.so.6 a8069000-a806b000 r--p 00133000 03:00 4222 /lib/libc.so.6 a806b000-a806c000 rw-p 00135000 03:00 4222 /lib/libc.so.6 a806c000-a806f000 rw-p 00000000 00:00 0 a806f000-a8083000 r-xp 00000000 03:00 14462 /lib/libpthread.so.0 a8083000-a8084000 r--p 00013000 03:00 14462 /lib/libpthread.so.0 a8084000-a8085000 rw-p 00014000 03:00 14462 /lib/libpthread.so.0 a8085000-a8088000 rw-p 00000000 00:00 0 a8088000-a80a4000 r-xp 00000000 03:00 8317 /lib/ld-linux.so.2 a80a4000-a80a5000 r--p 0001b000 03:00 8317 /lib/ld-linux.so.2 a80a5000-a80a6000 rw-p 0001c000 03:00 8317 /lib/ld-linux.so.2 afaf5000-afb0a000 rw-p 00000000 00:00 0 [stack] ffffe000-fffff000 r-xp 00000000 00:00 0 [vdso] Also there is a new entry "stack usage" in /proc/<pid>/{task/*,}/status which will you give the current stack usage in kb. A sample output of /proc/self/status looks like: Name: cat State: R (running) Tgid: 507 Pid: 507 . . . CapBnd: fffffffffffffeff voluntary_ctxt_switches: 0 nonvoluntary_ctxt_switches: 0 Stack usage: 12 kB I also fixed stack base address in /proc/<pid>/{task/*,}/stat to the base address of the associated thread stack and not the one of the main process. This makes more sense. [akpm@linux-foundation.org: fs/proc/array.c now needs walk_page_range()] Signed-off-by:Stefani Seibold <stefani@seibold.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Vincent Li authored
Remove obfuscated zero-length input check and return -EINVAL instead of -EIO error to make the error message clear to user. Add whitespace stripping. No functionality changes. The old code: echo 1 > /proc/pid/make-it-fail (ok) echo 1foo > /proc/pid/make-it-fail (-bash: echo: write error: Input/output error) The new code: echo 1 > /proc/pid/make-it-fail (ok) echo 1foo > /proc/pid/make-it-fail (-bash: echo: write error: Invalid argument) This patch is conservative in changes to not breaking existing scripts/applications. Signed-off-by:
Vincent Li <macli@brc.ubc.ca> Signed-off-by:
-
