- Record-based stream instead of the traditional byte stream
  buffer. All records carry a 64 bit timestamp, the syslog facility
  and priority in the record header.

- Records consume almost the same amount, sometimes less memory than
  the traditional byte stream buffer (if printk_time is enabled). The record
  header is 16 bytes long, plus some padding bytes at the end if needed.
  The byte-stream buffer needed 3 chars for the syslog prefix, 15 char for
  the timestamp and a newline.

- Buffer management is based on message sequence numbers. When records
  need to be discarded, the reading heads move on to the next full
  record. Unlike the byte-stream buffer, no old logged lines get
  truncated or partly overwritten by new ones. Sequence numbers also
  allow consumers of the log stream to get notified if any message in
  the stream they are about to read gets discarded during the time
  of reading.

- Better buffered IO support for KERN_CONT continuation lines, when printk()
  is called multiple times for a single line. The use of KERN_CONT is now
  mandatory to use continuation; a few places in the kernel need trivial fixes
  here. The buffering could possibly be extended to per-cpu variables to allow
  better thread-safety for multiple printk() invocations for a single line.

- Full-featured syslog facility value support. Different facilities
  can tag their messages. All userspace-injected messages enforce a
  facility value > 0 now, to be able to reliably distinguish them from
  the kernel-generated messages. Independent subsystems like a
  baseband processor running its own firmware, or a kernel-related
  userspace process can use their own unique facility values. Multiple
  independent log streams can co-exist that way in the same
  buffer. All share the same global sequence number counter to ensure
  proper ordering (and interleaving) and to allow the consumers of the
  log to reliably correlate the events from different facilities.
Tested-by: William Douglas <william.douglas@intel.com>
Signed-off-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 9fb48c74

    "params: add 3rd arg to option handler callback signature"

added an extra arg to the function, but didn't catch all the use
cases needing it, causing this compile fail in mpc85xx_defconfig:

 arch/powerpc/mm/hugetlbpage.c:316:4: error: passing argument 7 of
 'parse_args' from incompatible pointer type [-Werror]

 include/linux/moduleparam.h:317:12: note: expected
	 'int (*)(char *, char *, const char *)' but argument is of type
	 'int (*)(char *, char *)'

This function has no need to printk out the "doing" value, so
just add the arg as an "unused".

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Becky Bruce <beckyb@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 04db6e5f.

Odds are, we really don't want to revert all of these, and need to be
more careful in the future to make sure we don't break the build of
other arches.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I left 1 printk which uses __FILE__, __LINE__ explicitly, which should
not be subject to generic preferences expressed via pr_fmt().

+ tweaks suggested by Joe Perches:
- add doing to irq-enabled warning, like others.  It wont happen often..
- change sysfs failure crit, not just err, make it 1 line in logs.
- coalese 2 format fragments into 1 >80 char line

cc: Joe Perches <joe@perches.com>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These arent currently needed, so drop them.  Some will probably get
re-added when static-branches are added, but include loops prevent
that at present.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In commit 9fb48c74: "params: add 3rd arg to option handler callback
signature", the if-guard added to the pr_debug was overzealous; no
callers pass NULL, and existing code above and below the guard assumes
as much.  Change the if-guard to match, and silence the Smack
complaint.

CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

APIs using devres frequently want to implement a "remove and free the
resource" operation so it seems sensible that they should be able to
just have devres do the freeing for them since that's a big part of what
devres is all about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's not massively obvious (at least to me) that removing and freeing a
resource does not involve calling the release function for the resource
but rather only removes the management of it. Make the documentation more
explicit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

DEVICE_INT_ATTR() should use device_show_int() and device_store_int()
not device_show_ulong() and device_store_ulong()
Signed-off-by: Michael Davidson <md@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

NULL not 0 should be used with pointers. Just remove the offending
lines since they will default to NULL anyway.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some accessory detection mechanisms are able to detect that something is
physically present in the socket separately to identifying what is present
in the socket. This information can be useful to applications, for example
allowing them to indicate that a potentially broken accessory is present,
so provide a standard way to report it to userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make TI_EMIF depends on ARCH_OMAP2PLUS to avoid build breaks on other
architectures. In future if other TI non OMAP socs start using it, the
dependency can be extended.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the section mismatch be renaming the struct platform_driver
variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since no one using "dup_name", removed it completely in sysfs_rename.
Signed-off-by: Sasikantha babu <sasikanth.v19@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This was done to resolve a merge issue with the init/main.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add debug entries for:
	1. calculated registers per frequency
	2. last polled value of MR4(temperature level
	   of LPDDR2 memory)
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add settings that are not dependent on frequency
or any other transient parameters. This includes
- power managment control init
- impedence calibration control
- frequency independent phy configuration registers
- initialization of temperature polling
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add an ISR for EMIF that:
	1. reports details of access errors
	2. takes action on thermal events

Also clear all interrupts on shut-down. Pending IRQs
may casue problems during warm-reset.

Temperature handling:
EMIF can be configured to poll the temperature level
of an LPDDR2 device from the MR4 mode register in the
device. EMIF generates an interrupt whenever it identifies
a temperature level change between two consecutive pollings.

Some of the timing parameters need to be de-rated at high
temperatures. The interrupt handler takes care of doing
this and also takes care of going back to nominal settings
when temperature falls back to nominal levels.
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change SDRAM timings and other settings as necessary
on voltage and frequency changes. We calculate these
register settings based on data from the device data
sheet and inputs such a frequency, voltage state(stable
or ramping), temperature level etc.

TODO: frequency and voltage change handling needs to
be integrated with clock framework and regulator
framework respectively. This is not done today
due to missing pieces in the kernel.
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

EMIF is an SDRAM controller used in various Texas Instruments
SoCs. EMIF supports, based on its revision, one or more of
LPDDR2/DDR2/DDR3 protocols.

Add the basic infrastructure for EMIF driver that includes
driver registration, probe, parsing of platform data etc.
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add register offsets and bit field definitions
for EMIF module in TI SoCs
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

add LPDDR2 data from the JEDEC spec JESD209-2. The data
includes:

1. Addressing information for LPDDR2 memories of different
   densities and types(S2/S4)
2. AC timing data.

This data will useful for memory controller device drivers.
Right now this is used by the TI EMIF SDRAM controller
driver.
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/infiniband/ulp/srp/ib_srp.c #defines pr_fmt() PFX fmt, but PFX
is not #defined until after <linux/*> headers are included.

This results in a bad expansion of the pr_warn() in the stub function.

2084c2084
<   printk("<4>" PFX "dyndbg supported only in " "CONFIG_DYNAMIC_DEBUG builds\n")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1- Call dynamic_debug_init() from early_initcall, not arch_initcall.
2- Call dynamic_debug_init_debugfs() from fs_initcall, not module_init.

RFC: This works for me on a 64 bit desktop and a i586 SBC, but is
untested on other arches.  I presume there is or was a reason
original code used arch_initcall, maybe the constraints have changed.

This makes facility available as soon as possible.

2nd change has a downside when dynamic_debug.verbose=1; all the
vpr_info()s called in the proc-fs code are activated, causing
voluminous output from dmesg.  TBD: Im unsure of this explanation, but
the output is there.  This could be fixed by changing those callsites
to v2pr_info(if verbose > 1).

1st change is still not early enough to enable pr_debugs in
kernel/params, so parsing of boot-args isnt logged.  The reparse of
those args is however visible after params.dyndbg="+p" is processed.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In dynamic-debug-howto.txt:

- add section: Debug Messages at Module Initialization Time
- update flags indicators in example outputs to include '='
- make flags descriptions tabular
- add item on '_' flag-char
- add dyndbg, boot-args examples
- rewrap some paragraphs with long lines

In Kconfig.debug, note that compiling with -DDEBUG enables all
pr_debug()s in that code.

In kernel-parameters.txt, add dyndbg and module.dyndbg items,
and deprecate ddebug_query.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pass module name into ddebug_exec_queries(), ddebug_exec_query(), and
ddebug_parse_query() as separate parameter.  In ddebug_parse_query(),
the module name is added into the query struct before the query-string
is parsed.  This allows the query-string to be shorter:

instead of:
   $modname.dyndbg="module $modname +fp"
do this:
   $modname.dyndbg="+fp"

Omitting "module $modname" from the query string is actually required
for $modname.dyndbg rules; the set-only-once check added in a previous
patch will throw an error if its added again.  ddebug_query="..." has
no $modname associated with it, so the query string may include it.

This also fixes redundant "module $modname" otherwise needed to handle
multiple queries per string:

   $modname.dyndbg="func foo +fp; func bar +fp"
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Print ram usage of dynamic-debug tables and verbose section so user
knows cost of enabling CONFIG_DYNAMIC_DEBUG.  This only counts the
size of the _ddebug tables for builtins and the __verbose section that
they refer to, not those used in loadable modules.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We dont want errors while parsing ddebug_query to unload ddebug
tables, so set success after tables are loaded, and return 0 after
query parsing is done.

Simplify error handling code since its no longer used for success,
and change goto label to out_err to clarify this.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor ddebug_dyndbg_boot_param_cb and ddebug_dyndbg_module_param_cb
into a common helper function, and call it from both.  The handling of
foo.dyndbg is unneeded by the latter, but harmless.

The 2 callers differ only by pr_info and the return code they pass to
the helper for when an unknown param is handled.  I could slightly
reduce dmesg clutter by putting the vpr_info in the common helper,
after the return on_err, but that loses __func__ context, is overly
silent on module_cb unknown param errors, and the clutter is only when
dynamic_debug.verbose=1 anyway.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With ddebug_dyndbg_boot_params_cb() handling bare dyndbg params, we
dont need ddebug_query param anymore.  Add a warning when processing
ddebug_query= param that it is deprecated, and to change it to dyndbg=

Add a deprecation notice for v3.8 to feature-removal-schedule.txt, and
add a suggested deprecation period of 3 releases to the header.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This introduces a fake module param $module.dyndbg.  Its based upon
Thomas Renninger's $module.ddebug boot-time debugging patch from
https://lkml.org/lkml/2010/9/15/397

The 'fake' module parameter is provided for all modules, whether or
not they need it.  It is not explicitly added to each module, but is
implemented in callbacks invoked from parse_args.

For builtin modules, dynamic_debug_init() now directly calls
parse_args(..., &ddebug_dyndbg_boot_params_cb), to process the params
undeclared in the modules, just after the ddebug tables are processed.

While its slightly weird to reprocess the boot params, parse_args() is
already called repeatedly by do_initcall_levels().  More importantly,
the dyndbg queries (given in ddebug_query or dyndbg params) cannot be
activated until after the ddebug tables are ready, and reusing
parse_args is cleaner than doing an ad-hoc parse.  This reparse would
break options like inc_verbosity, but they probably should be params,
like verbosity=3.

ddebug_dyndbg_boot_params_cb() handles both bare dyndbg (aka:
ddebug_query) and module-prefixed dyndbg params, and ignores all other
parameters.  For example, the following will enable pr_debug()s in 4
builtin modules, in the order given:

  dyndbg="module params +p; module aio +p" module.dyndbg=+p pci.dyndbg

For loadable modules, parse_args() in load_module() calls
ddebug_dyndbg_module_params_cb().  This handles bare dyndbg params as
passed from modprobe, and errors on other unknown params.

Note that modprobe reads /proc/cmdline, so "modprobe foo" grabs all
foo.params, strips the "foo.", and passes these to the kernel.
ddebug_dyndbg_module_params_cb() is again called for the unknown
params; it handles dyndbg, and errors on others.  The "doing" arg
added previously contains the module name.

For non CONFIG_DYNAMIC_DEBUG builds, the stub function accepts
and ignores $module.dyndbg params, other unknowns get -ENOENT.

If no param value is given (as in pci.dyndbg example above), "+p" is
assumed, which enables all pr_debug callsites in the module.

The dyndbg fake parameter is not shown in /sys/module/*/parameters,
thus it does not use any resources.  Changes to it are made via the
control file.

Also change pr_info in ddebug_exec_queries to vpr_info,
no need to see it all the time.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
CC: Thomas Renninger <trenn@suse.de>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a 3rd arg, named "doing", to unknown-options callbacks invoked
from parse_args(). The arg is passed as:

  "Booting kernel" from start_kernel(),
  initcall_level_names[i] from do_initcall_level(),
  mod->name from load_module(), via parse_args(), parse_one()

parse_args() already has the "name" parameter, which is renamed to
"doing" to better reflect current uses 1,2 above.  parse_args() passes
it to an altered parse_one(), which now passes it down into the
unknown option handler callbacks.

The mod->name will be needed to handle dyndbg for loadable modules,
since params passed by modprobe are not qualified (they do not have a
"$modname." prefix), and by the time the unknown-param callback is
called, the module name is not otherwise available.

Minor tweaks:

Add param-name to parse_one's pr_debug(), current message doesnt
identify the param being handled, add it.

Add a pr_info to print current level and level_name of the initcall,
and number of registered initcalls at that level.  This adds 7 lines
to dmesg output, like:

   initlevel:6=device, 172 registered initcalls

Drop "parameters" from initcall_level_names[], its unhelpful in the
pr_info() added above.  This array is passed into parse_args() by
do_initcall_level().

CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clean up some space-before-tabs problems.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use vpr_info to declutter code, reduce indenting, and change one
additional pr_info call in ddebug_exec_queries.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit f19420c1.

It contained lots of errors and warnings and shouldn't have ever been
applied, that was my fault, sorry.

Cc: Markus Franke <markus.franke@s2002.tu-chemnitz.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>,
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch inform the state of only one cable instead of previous data
including the state of 32 cables to notifee which use
extcon_register_interest()
function to monitor whether the specific cable is attachd or detached.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull power management fixes from Rafael J. Wysocki:
 "Fix for an issue causing hibernation to hang on systems with highmem
  (that practically means i386) due to broken memory management (bug
  introduced in 3.2, so -stable material) and PM documentation update
  making the freezer documentation follow the code again after some
  recent updates."

* tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / Freezer / Docs: Update documentation about freezing of tasks
  PM / Hibernate: fix the number of pages used for hibernate/thaw buffering