- 11 Nov, 2013 1 commit
-
-
Huang Shijie authored
We cannot scan two chips for imx23 and imx28: imx23: the Ready-Busy1 line is not connected for some board. imx28: we do not set the pinctrl for Ready-Busy1 So we only scan two chips for imx6. Signed-off-by:
Huang Shijie <b32955@freescale.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com>
-
- 07 Nov, 2013 39 commits
-
-
Fabio Estevam authored
Using devm_kzalloc() can make the code simpler. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Acked-by:
-
Josh Wu authored
In the atmel driver probe function, the code shows like following: atmel_nand_probe(...) { ... err_nand_ioremap: platform_driver_unregister(&atmel_nand_nfc_driver); return res; } If no nand flash detected, the driver probe function will goto err_nand_ioremap label. Then platform_driver_unregister() will be called. It will get the lock of atmel_nand device since it is parent of nfc_device. The problem is the lock is already hold by atmel_nand_probe itself. So system will be in a dead lock. This patch just simply removed to platform_driver_unregister() call. When atmel_nand driver is quit the platform_driver_unregister() will be called in atmel_nand_remove(). [Brian: the NAND platform probe really has no business registering/unregistering another driver; this fixes the deadlock, but we should follow up the likely racy behavior here with a better architecture] Signed-off-by:Josh Wu <josh.wu@atmel.com> Cc: <stable@vger.kernel.org> # 3.12 Signed-off-by:
-
Huang Shijie authored
There are too many "chip->ecc" in the nand_scan_tail() which makes the eyes sore. This patch uses a local variable "ecc" to replace the "chip->ecc" to make the code more graceful. Do the code change with "s/chip->ecc\./ecc->/g" in the nand_scan_tail, and also change some lines by hand. Signed-off-by:
-
Michael Opdenacker authored
This patch proposes to remove the use of the IRQF_DISABLED flag It's a NOOP since 2.6.35 and it will be removed one day. Signed-off-by:
Michael Opdenacker <michael.opdenacker@free-electrons.com> Signed-off-by:
-
Mark Brown authored
Ensure that the error message if we identify a flash we don't know how to talk to is displayed on the console in order to aid diagnostics. While we're at convert the message to use dev_info() rather than our hand rolled version of it for consistency. Signed-off-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Wei Yongjun authored
Fix to return a negative error code from the error handling case instead of 0, to more closely match the rest of this function. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Acked-by:
Pekon Gupta <pekon@ti.com> Signed-off-by:
-
Brian Norris authored
Now that the last user of NAND_BBT_SCANALLPAGES has been removed, let's kill this peculiar BBT feature flag. Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
-
Brian Norris authored
Device removal should fail if MTD unregistration fails. Signed-off-by:
Marek Vasut <marex@denx.de>
-
Sachin Kamat authored
'of_match_ptr' is defined in linux/of.h. Include it explicitly to avoid build breakage in the future. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Wei Yongjun authored
Remove duplicated include. Signed-off-by:
-
Brian Norris authored
A new 32Mbit SPI NOR flash from Macronix. Nothing special. Signed-off-by:
-
Pekon Gupta authored
With OMAP NAND driver updates, selection of ecc-scheme: *DT enabled kernel* depends on ti,nand-ecc-opt and ti,elm-id DT bindings. *Non DT enabled kernel* depends on elm_dev and ecc-scheme passed along with platform-data from board file. So, selection of ecc-scheme (BCH8 or BCH4) from KConfig can be removed Signed-off-by:
-
Pekon Gupta authored
"Managed Device Resource" or devm_xx calls takes care of automatic freeing of the resource in case of: - failure during driver probe - failure during resource allocation - detaching or unloading of driver module (rmmod) Reference: Documentation/driver-model/devres.txt Though OMAP NAND driver handles freeing of resource allocation in most of the cases, but using devm_xx provides more clean and effortless approach to handle all such cases. - simplifies label for exiting probe during error s/out_release_mem_region/return_error Signed-off-by:
-
Pekon Gupta authored
generic frame-work in mtd/nand/nand_bch.c is a wrapper above lib/bch.h which encapsulates all control information specific to BCH ecc algorithm in software. Thus this patch: (1) replace omap specific implementations with equivalent wrapper in nand_bch.c so that generic code from nand_bch.c is re-used. like; omap3_correct_data_bch() -> nand_bch_correct_data() omap3_free_bch() -> nand_bch_free() (2) replace direct calls to lib/bch.c with wrapper functions defined in nand_bch.c init_bch() -> nand_bch_init() Signed-off-by: -
Pekon Gupta authored
In current implementation omap3_init_bch_tail() is a common function to define ecc layout for different BCHx ecc schemes.This patch: (1) removes omap3_init_bch_tail() and defines ecc layout for individual ecc-schemes along with populating their nand_chip->ecc data in omap_nand_probe(). This improves the readability and scalability of code for add new ecc schemes in future. (2) removes 'struct nand_bbt_descr bb_descrip_flashbased' because default nand_bbt_descr in nand_bbt.c matches the same (.len=1 for x8 devices). (3) add the check to see if NAND device has enough OOB/Spare bytes to store ECC signature of whole page, as defined by ecc-scheme. Signed-off-by: -
Pekon Gupta authored
current implementation in omap3_init_bch() has some redundant code like: (1) omap3_init_bch() re-probes the DT-binding to detect presence of ELM h/w engine on SoC. And based on that it selects implemetation of ecc-scheme. However, this is already done as part of GPMC DT parsing. (2) As omap3_init_bch() serves as common function for configuring all types of BCHx ecc-schemes, so there are multiple levels of redudant if..then..else checks while populating nand_chip->ecc. This patch make following changes to OMAP NAND driver: (1) removes omap3_init_bch(): each ecc-scheme is individually configured in omap_nand_probe() there by removing redundant if..then..else checks. (2) adds is_elm_present(): re-probing of ELM device via DT is not required as it's done in GPMC driver probe. Thus is_elm_present() just initializes ELM driver with NAND probe data, when ecc-scheme with h/w based error-detection is used. (3) separates out configuration of different flavours of "BCH4" and "BCH8" ecc-schemes as given in below table (4) conditionally compiles callbacks implementations of ecc.hwctl(), ecc.calculate(), ecc.correct() to avoid warning of un-used functions. +---------------------------------------+---------------+---------------+ | ECC scheme |ECC calculation|Error detection| +---------------------------------------+---------------+---------------+ |OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W | +---------------------------------------+---------------+---------------+ |OMAP_ECC_BCH4_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W (lib/bch.c)| | (needs CONFIG_MTD_NAND_ECC_BCH) | | | | | | | |OMAP_ECC_BCH4_CODE_HW |H/W (GPMC) |H/W (ELM) | | (needs CONFIG_MTD_NAND_OMAP_BCH && | | | | ti,elm-id) | | | +---------------------------------------+---------------+---------------+ |OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W (lib/bch.c)| | (needs CONFIG_MTD_NAND_ECC_BCH) | | | | | | | |OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) | | (needs CONFIG_MTD_NAND_OMAP_BCH && | | | | ti,elm-id) | | | +---------------------------------------+---------------+---------------+ - 'CONFIG_MTD_NAND_ECC_BCH' is generic KConfig required to build lib/bch.c which is required for ECC error detection done in software. (mainly used for legacy platforms which do not have on-chip ELM engine) - 'CONFIG_MTD_NAND_OMAP_BCH' is OMAP specific Kconfig to detemine presence on ELM h/w engine on SoC. Signed-off-by: -
Pekon Gupta authored
This patch: - calls nand_scan_ident() using bus-width as passed by DT - removes double calls to nand_scan_ident(), in case first call fails then omap_nand_probe just returns error. Signed-off-by:
-
Pekon Gupta authored
This patch updates following in omap_nand_probe() and omap_nand_remove() - replaces "info->nand" with "nand_chip" (struct nand_chip *nand_chip) - replaces "info->mtd" with "mtd" (struct mtd_info *mtd) - white-space and formatting cleanup Signed-off-by:
-
Pekon Gupta authored
OMAP NAND driver currently supports multiple flavours of 1-bit Hamming ecc-scheme, like: - OMAP_ECC_HAMMING_CODE_DEFAULT 1-bit hamming ecc code using software library - OMAP_ECC_HAMMING_CODE_HW 1-bit hamming ecc-code using GPMC h/w engine - OMAP_ECC_HAMMING_CODE_HW_ROMCODE 1-bit hamming ecc-code using GPMC h/w engin with ecc-layout compatible to ROM code. This patch combines above multiple ecc-schemes into single implementation: - OMAP_ECC_HAM1_CODE_HW 1-bit hamming ecc-code using GPMC h/w engine with ROM-code compatible ecc-layout. Signed-off-by:
Felipe Balbi <balbi@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> Tested-by:
-
Pekon Gupta authored
OMAP NAND driver support multiple ECC scheme, which can used in different flavours, depending on in-build Hardware engines present on SoC. This patch updates following in DT bindings related to sectionion of ecc-schemes - ti,elm-id: replaces elm_id (maintains backward compatibility) - ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme depends on ti,elm-id. (supported values ham1, bch4, and bch8) - maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode) Below table shows different flavours of ecc-schemes supported by OMAP devices +---------------------------------------+---------------+---------------+ | ECC scheme |ECC calculation|Error detection| +---------------------------------------+---------------+---------------+ |OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W | +---------------------------------------+---------------+---------------+ |OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W | |(requires CONFIG_MTD_NAND_ECC_BCH) | | | +---------------------------------------+---------------+---------------+ |OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) | |(requires CONFIG_MTD_NAND_OMAP_BCH && | | | | ti,elm-id in DT) | | | +---------------------------------------+---------------+---------------+ To optimize footprint of omap2-nand driver, selection of some ECC schemes also require enabling following Kconfigs, in addition to setting appropriate DT bindings - Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software - Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine Signed-off-by:
-
Brian Norris authored
It seems like the following commit was never necessary commit 5f949137 Author: Shaohui Xie <Shaohui.Xie@freescale.com> Date: Fri Oct 14 15:49:00 2011 +0800 mtd: m25p80: don't probe device which has status of 'disabled' because it duplicates the code in of_platform_device_create_pdata() which ensures that 'disabled' nodes are never instantiated. Also, drop the __maybe_unused. Signed-off-by:Sourav Poddar <sourav.poddar@ti.com> Reviewed-by:
Grant Likely <grant.likely@linaro.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: <devicetree@vger.kernel.org>
-
Brian Norris authored
Remove the compile-time option for FAST_READ, since we have run-time support for detecting it. This refactors the logic for enabling fast-read, such that for DT-enabled devices, we honor the "m25p,fast-read" property but for non-DT devices, we default to using FAST_READ whenever the flash device supports it. Normal READ and FAST_READ differ only in the following: * FAST_READ supports SPI higher clock frequencies [1] * number of dummy cycles; FAST_READ requires 8 dummy cycles (whereas READ requires 0) to allow the flash sufficient setup time, even when running at higher clock speeds Thus, for flash chips which support FAST_READ, there is otherwise no limiting reason why we cannot use the FAST_READ opcode instead of READ. It simply allows the SPI controller to run at higher clock rates. So theoretically, nobody should be needing the compile-time option anyway. [1] I have a Spansion S25FL128S datasheet which says: "The maximum operating clock frequency for the READ command is 50 MHz." And: "The maximum operating clock frequency for FAST READ command is 133 MHz." Signed-off-by: -
Brian Norris authored
No change in the table data. Signed-off-by:
-
Brian Norris authored
The FIXME and NOTE have already been fixed (we have FAST_READ support). Signed-off-by:
-
Brian Norris authored
This patch fixes two memory errors: 1. During a probe failure (in mtd_device_parse_register?) the command buffer would not be freed. 2. The command buffer's size is determined based on the 'fast_read' boolean, but the assignment of fast_read is made after this allocation. Thus, the buffer may be allocated "too small". To fix the first, just switch to the devres version of kzalloc. To fix the second, increase MAX_CMD_SIZE unconditionally. It's not worth saving a byte to fiddle around with the conditions here. This problem was reported by Yuhang Wang a while back. Signed-off-by:
Yuhang Wang <wangyuhang2014@gmail.com> Reviewed-by:
-
Huang Shijie authored
In the imx6, all the ready/busy pins are binding togeter. So we should always check the ready/busy pin of the chip 0. In the other word, when the CS1 is enabled, we should also check the ready/busy of chip 0; if we check the ready/busy of chip 1, we will get the wrong result. Signed-off-by:
-
Huang Shijie authored
Some nand chip has two DIEs in a single chip, such as Micron MT29F32G08QAA. Each die has its own chip select pin, so this chip acts as two nand chips. If we only scan one chip, we may find that we only get 2G for this chip, but in actually, this chip's size is 4G. So scan two chips by default. Signed-off-by:
-
Huang Shijie authored
We only have one DMA channel : the channel 0. Use DMA channel 0 to access all the nand chips. Signed-off-by:
-
Huang Shijie authored
Decouple the chip select from the DMA channel, we use the DMA channel 0 to accecc all the nand devices. Signed-off-by:
-
Prabhakar Kushwaha authored
as per controller description, "While programming a NAND flash, status read should never skipped. Because it may happen that a new command is issued to the NAND Flash, even when the device has not yet finished processing the previous request. This may result in unpredictable behaviour." IFC controller never polls for R/B signal after command send. It just return control to software. This behaviour may not occur with NAND flash access. because new commands are sent after polling R/B signal. But it may happen in scenario where GPCM-ASIC and NAND flash device are working simultaneously. Update the controller driver to take care of this requirement Signed-off-by:
Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by:
-
Prabhakar Kushwaha authored
Current IFC driver supports till 4K page size NAND flash. Add support of 8K Page size NAND flash - Add nand_ecclayout for 4 bit & 8 bit ecc - Defines constants - also fix ecc.strength for 8bit ecc of 8K page size NAND Signed-off-by:
-
Wang Haitao authored
Hardware: CPU: XLP832,the 64-bit OS NOR Flash:S29GL128S 128M Software: Kernel:2.6.32.41 Filesystem:JFFS2 When writing files, errors appear: Write len 182 but return retlen 180 Write of 182 bytes at 0x072c815c failed. returned -5, retlen 180 Write len 186 but return retlen 184 Write of 186 bytes at 0x072caff4 failed. returned -5, retlen 184 These errors exist only in 64-bit systems,not in 32-bit systems. After analysis, we found that the left shift operation is wrong in map_word_load_partial. For instance: unsigned char buf[3] ={0x9e,0x3a,0xea}; map_bankwidth(map) is 4; for (i=0; i < 3; i++) { int bitpos; bitpos = (map_bankwidth(map)-1-i)*8; orig.x[0] &= ~(0xff << bitpos); orig.x[0] |= buf[i] << bitpos; } The value of orig.x[0] is expected to be 0x9e3aeaff, but in this situation(64-bit System) we'll get the wrong value of 0xffffffff9e3aeaff due to the 64-bit sign extension: buf[i] is defined as "unsigned char" and the left-shift operation will convert it to the type of "signed int", so when left-shift buf[i] by 24 bits, the final result will get the wrong value: 0xffffffff9e3aeaff. If the left-shift bits are less than 24, then sign extension will not occur. Whereas the bankwidth of the nor flash we used is 4, therefore this BUG emerges. Signed-off-by:Pang Xunlei <pang.xunlei@zte.com.cn> Signed-off-by:
Zhang Yi <zhang.yi20@zte.com.cn> Signed-off-by:
Lu Zhongjun <lu.zhongjun@zte.com.cn> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Ezequiel Garcia authored
This patch moves the char and block major number definitions to major.h to be with the rest of the major numbers. While doing this, include major.h in the files that need it. Signed-off-by:
-
Rafał Miłecki authored
A new type of partition with magic FCTY was found on Huawei E970: 46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290| Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
Most of the bcm47xx devices use TRX format for storing kernel and some partition like Squashfs or JFFS2. This is pretty flexible solution, CFE (the bootloader) just writes (and later boots) TRX at some hardcoded place and paritions can vary in the size. However some devices don't use TRX format. Very recently we have discovered ZTE H218N that has kernel and rootfs partitions at some "random" places. This patch allows Linux find a rootfs partition after installing custom image with a CFE bootloader. Signed-off-by:
-
Hauke Mehrtens authored
Handle return NULL in malloc. Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
-
Sachin Kamat authored
devm_kzalloc is device managed and simplifies the code. Signed-off-by:
-
Sachin Kamat authored
module_platform_driver simplifies the code by removing boiler plate. Signed-off-by:
-
Sachin Kamat authored
module_platform_driver simplifies the code by removing boiler plate. Signed-off-by:
-
