In order to allow using the same brd file across different
11ad chips, the address for loading the brd file should be
part of the FW file, instead of the brd file. The brd file is
expected to include only one section.
To allow backward compatibility the driver reads the
address from the brd file in case it is not included in the
FW file.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

PCIe device ID has changed in Talyn.
Add this ID to wil6210_pcie_ids list to allow
recognition of Talyn device.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Jiri Pirko says:

====================
mlxsw: Add support for mirror action with flower

Arkadi says:

Add support for mirror action with flower classifier. The first 3 patches
introduce a generic per-block resource infra. The last 4 patches add
support for flow based span.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for mirror action. Only one mirror action can be set per rule.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce extension of mlxsw_afa_ops in order to add/del mirroring and
implement the ops for Spectrum.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend SPAN API for ACL case. In case of ACL triggering the MPAR register
shouldn't be configured. This patch also export those helpers for
ACL usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch extends the trap action for mirroring.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far, the caller of mlxsw_afa_block_append_counter needed to allocate
counter index by hand. Benefit from the previously introduced resource
infra and counter_index_get/put callbacks, and allocate the counter
index in place where it is needed, inside the action append function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the resource list needs to be used also for other entries different
to fwd_entry_ref, make the list generic. For that purpose, introduce a
resource structure with couple of helpers that the code which need to
store a per-block resource should use.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce extension of mlxsw_afa_ops in order to get/put counter indexes
and implement the ops for Spectrum.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
Aquantia atlantic driver new devices support

This patchset introduces a support for new Aquantia hardware:
AQC11x family with updated hardware (B1) and firmware (2.x and 3.x branches).

For that, a number of improvements in overall driver model were done:
 - Firmware specific ops tables. Firmware 2.x and 3.x series support
   functions are now in separate fw2x module.
 - PCI module cleanup and simplification done.
 - Verified and tested hardware reset process.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For devices with known capabilities of Fibre media type we now report that
to ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The detailed reset sequence ensures all HW components are in aligned
state before NIC startup. It also supports cards with signed firmware (RBL)
and checks if their FW is valid.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This defines fw2x operations table and corresponding methods.
Some of the functions are being shared with 1.x firmware
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New AQC cards will have an updated firmware with new binary interface.
This patch extracts firmware specific operations into a separate table
and prepares for the introduction of new fw 2.x and 3.x
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The address to check if HW is not dead/hang could be stored in
capabilities, since it is a constant. Change its name to better reflect
the idea.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These ops are not related to HW and are now implemented in pci module.
Thus, remove these ops pointers and implementation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver contained a dead code of maintaining multiple pci port instances.
That will never be used since for each pci function a separate NIC
instance is created.
Simplify this, making pci module only responsible for pci resource
management.
NIC initialization is also simplified accordingly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes unnecessary structure copying, and prepares the driver for
separate firmware ops table introduction.

We also remove extra copy of capabilities structure (which is const actually)
and also replace it with a const pointer in aq_nic_cfg.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of new AQC devices is going to be released. To support more
flexible capabilities management a number of static caps instances is now
declared. Devices now are mainly differs by supported speeds, but in future
more parameters will be customized. A set of AQC100 devices have
fibre media, not twisted pair - this is also reflected in
new capabilities definitions.

HW level also now directly exports hw_ops for each of A0/B0 hardware.

PCI configuration now uses a device configuration table where each
device ID is explicitly mapped with hardware OPs and capabilities
structures.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New set of aquantia devices has an upgraded hardware (B1).
The hardware interface is identical to B0. The difference will
be in firmware which is incompatible with old one.

Reorganized and removed duplicate speed and devid definitions
Introduced explicit flow control configuration defines
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2018-01-19

From: Or Gerlitz <ogerlitz@mellanox.com>
=======
First six patches of this series further enhances the mlx5 hairpin support.
The first two patches deal with using different hairpin instances
for flows whose packets have different priorities to align with the port
TX QoS model. The next four patches allow us to do HW spreading
of flows over a set of hairpin pairs using RSS. The last two patches
change the driver to also set the size of the HW hairpin queues.
========

Next four patches from Eran Ben Elisha <eranbe@mellanox.com>:
Add more debug data for TX timeout handling, and further enhance and optimize
TX timeout handling upon lost interrupts, which adds a mechanism for explicitly
polling EQ in case of a TX timeout in order to recover from a lost interrupt.
If this is not the case (no pending EQEs), perform a channels full recovery as
usual.

From Kamal Heib <kamalh@mellanox.com>, Two patches to extend the stats group API
to have an update_stats() callback which will be used to fetch the hardware or
software counters data, this will improve the current API and reduce code
duplication.

From Gal Pressman <galp@mellanox.com>, Last patch, Add likely to the common RX checksum
flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously it was possible to interrupt processing stats updates because
they were handled in a work queue. Interrupting the stats updates could
lead to a situation where we backup the control message queue. This patch
moves the stats update processing out of the work queue to be processed as
soon as hardware sends a request.
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The zeroday builder notices that since Usermode Linux does not
have IO memory, the build fails for them when selecting everything
it can enable.

As the driver is clearly using memory-mapped registers to access
the network adapter, we add depends on HAS_IOMEM to solve this
problem.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains Netfilter/IPVS updates for your net-next
tree. Basically, a new extension for ip6tables, simplification work of
nf_tables that saves us 500 LoC, allow raw table registration before
defragmentation, conversion of the SNMP helper to use the ASN.1 code
generator, unique 64-bit handle for all nf_tables objects and fixes to
address fallout from previous nf-next batch.  More specifically, they
are:

1) Seven patches to remove family abstraction layer (struct nft_af_info)
   in nf_tables, this simplifies our codebase and it saves us 64 bytes per
   net namespace.

2) Add IPv6 segment routing header matching for ip6tables, from Ahmed
   Abdelsalam.

3) Allow to register iptable_raw table before defragmentation, some
   people do not want to waste cycles on defragmenting traffic that is
   going to be dropped, hence add a new module parameter to enable this
   behaviour in iptables and ip6tables. From Subash Abhinov
   Kasiviswanathan. This patch needed a couple of follow up patches to
   get things tidy from Arnd Bergmann.

4) SNMP helper uses the ASN.1 code generator, from Taehee Yoo. Several
   patches for this helper to prepare this change are also part of this
   patch series.

5) Add 64-bit handles to uniquely objects in nf_tables, from Harsha
   Sharma.

6) Remove log message that several netfilter subsystems print at
   boot/load time.

7) Restore x_tables module autoloading, that got broken in a previous
   patch to allow singleton NAT hook callback registration per hook
   spot, from Florian Westphal. Moreover, return EBUSY to report that
   the singleton NAT hook slot is already in instead.

8) Several fixes for the new nf_tables flowtable representation,
   including incorrect error check after nf_tables_flowtable_lookup(),
   missing Kconfig dependencies that lead to build breakage and missing
   initialization of priority and hooknum in flowtable object.

9) Missing NETFILTER_FAMILY_ARP dependency in Kconfig for the clusterip
   target. This is due to recent updates in the core to shrink the hook
   array size and compile it out if no specific family is enabled via
   .config file. Patch from Florian Westphal.

10) Remove duplicated include header files, from Wei Yongjun.

11) Sparse warning fix for the NFPROTO_INET handling from the core
    due to missing static function definition, also from Wei Yongjun.

12) Restore ICMPv6 Parameter Problem error reporting when
    defragmentation fails, from Subash Abhinov Kasiviswanathan.

13) Remove obsolete owner field initialization from struct
    file_operations, patch from Alexey Dobriyan.

14) Use boolean datatype where needed in the Netfilter codebase, from
    Gustavo A. R. Silva.

15) Remove double semicolon in dynset nf_tables expression, from
    Luis de Bethencourt.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf-next 2018-01-19

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) bpf array map HW offload, from Jakub.

2) support for bpf_get_next_key() for LPM map, from Yonghong.

3) test_verifier now runs loaded programs, from Alexei.

4) xdp cpumap monitoring, from Jesper.

5) variety of tests, cleanups and small x64 JIT optimization, from Daniel.

6) user space can now retrieve HW JITed program, from Jiong.

Note there is a minor conflict between Russell's arm32 JIT fixes
and removal of bpf_jit_enable variable by Daniel which should
be resolved by keeping Russell's comment and removing that variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The BPF verifier conflict was some minor contextual issue.

The TUN conflict was less trivial.  Cong Wang fixed a memory leak of
tfile->tx_array in 'net'.  This is an skb_array.  But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
This series adds various misc improvements to BPF: detection
of BPF helper definition misconfiguration for mem/size argument
pairs, csum_diff helper also for XDP, various test cases,
removal of the recently added pure_initcall(), restriction
of the jit sysctls to cap_sys_admin for initns, a minor size
improvement for x86 jit in alu ops, output of complexity limit
to verifier log and last but not least having the event output
more flexible with moving to const_size_or_zero type.

Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Similar rationale as in a60dd35d ("bpf: change bpf_perf_event_output
arg5 type to ARG_CONST_SIZE_OR_ZERO"), change the type to CONST_SIZE_OR_ZERO
such that we can better deal with optimized code. No changes needed in
bpf_event_output() as it can also deal with 0 size entirely (e.g. as only
wake-up signal with empty frame in perf RB, or packet dumps w/o meta data
as another such possibility).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Given the limit could potentially get further adjustments in the
future, add it to the log so it becomes obvious what the current
limit is w/o having to check the source first. This may also be
helpful for debugging complexity related issues on kernels that
backport from upstream.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

For the BPF_REG_0 (BPF_REG_A in cBPF, respectively), we can use
the short form of the opcode as dst mapping is on eax/rax and
thus save a byte per such operation. Added to add/sub/and/or/xor
for 32/64 bit when K immediate is used. There may be more such
low-hanging fruit to add in future as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Given BPF reaches far beyond just networking these days, it was
never intended to allow setting and in some cases reading those
knobs out of a user namespace root running without CAP_SYS_ADMIN,
thus tighten such access.

Also the bpf_jit_enable = 2 debugging mode should only be allowed
if kptr_restrict is not set since it otherwise can leak addresses
to the kernel log. Dump a note to the kernel log that this is for
debugging JITs only when enabled.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>