Simply use netdev_priv() to replace netdev->priv.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Usually, netdev->priv should point to the memory of private
data which is allocated in alloc_netdev().
netdev_priv() is used to get the address of the private data.

Change the netdev->priv pointer to another memory is wrong.
Use netdev->ml_priv for this case.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Installing SAs using the XFRM_STATE_AF_UNSPEC fails on hosts with
support for one address family only. This patch accepts such SAs, even
if the processing of not supported packets will fail.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Used __xfrm_policy_unlink() to instead of the dup codes when unlink
SPD entry.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After flush the SPD entries, dump the SPD entries will cause kernel painc.

Used the following commands to reproduct:

- echo 'spdflush;' | setkey -c
- echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64  any -P out ipsec \
  ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\
  spddump;' | setkey -c
- echo 'spdflush; spddump;' | setkey -c
- echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64  any -P out ipsec \
  ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\
  spddump;' | setkey -c

This is because when flush the SPD entries, the SPD entry is not remove
from the list.

This patch fix the problem by remove the SPD entry from the list.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:

	drivers/net/ixgbe/ixgbe_main.c
	drivers/net/smc91x.c

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] hpwdt: Fix kdump when using hpwdt
  [WATCHDOG] hpwdt: set the mapped BIOS address space as executable
  [WATCHDOG] iTCO_wdt: add PCI ID's for ICH9 & ICH10 chipsets
  [WATCHDOG] iTCO_wdt : correct status clearing
  [WATCHDOG] iTCO_wdt : problem with rebooting on new ICH9 based motherboards
  [WATCHDOG] fix mtx1_wdt compilation failure

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: pre-allocate bulk-read buffer
  UBIFS: do not allocate too much
  UBIFS: do not print scary memory allocation warnings
  UBIFS: allow for gaps when dirtying the LPT
  UBIFS: fix compilation warnings
  MAINTAINERS: change UBI/UBIFS git tree URLs
  UBIFS: endian handling fixes and annotations
  UBIFS: remove printk

* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: MMU: avoid creation of unreachable pages in the shadow
  KVM: ppc: stop leaking host memory on VM exit
  KVM: MMU: fix sync of ptes addressed at owner pagetable
  KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER
  KVM: ia64: Fix incorrect kbuild CFLAGS override
  KVM: VMX: Fix interrupt loss during race with NMI
  KVM: s390: Fix problem state handling in guest sigp handler

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix offset calculation in compute_size()
  rtc: rtc-starfire fixes

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
  MAINTAINERS: add netdev to ATM
  ATM: horizon, fix hrz_probe fail path
  pppol2tp: Add missing sock_put() in pppol2tp_release()
  net: Fix soft lockups/OOM issues w/ unix garbage collector
  macvlan: don't broadcast PAUSE frames to macvlan devices
  Phonet: fix oops in phonet_address_del() on non-Phonet device
  netfilter: ctnetlink: fix GFP_KERNEL allocation under spinlock
  sungem: Fix PCS_MIICTRL register write in gem_init_phy().
  net: make skb_truesize_bug() call WARN()
  net: hp-plus uses eip_poll
  net/wireless/reg.c: fix bad WARN_ON in if statement
  ath5k: disable beacon filter when station is not associated
  ath5k: fix Security issue in DebugFS part of ath5k
  ath9k: correct expected max RX buffer size
  ath9k: Fix SW-IOMMU bounce buffer starvation
  mac80211 : Fix setting ad-hoc mode and non-ibss channel
  iwlagn: fix DMA sync
  phylib: Add Vitesse VSC8221 SGMII PHY
  rose: zero length frame filtering in af_rose.c
  bridge: netfilter: fix update_pmtu crash with GRE
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Update defconfigs for 2.6.28-rc7
  macfb: Do not overflow fb_fix_screeninfo.id

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  alim15x3: fix sparse warning
  ide: remove dead code from drive_is_ready()
  ide: fix build for DEBUG_PM
  ide: respect current DMA setting during resume
  ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[]
  amd74xx: workaround unreliable AltStatus register for nVidia controllers
  ide: fix the ide_release_lock imbalance

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] stex: switch to block timeout
  [SCSI] make scsi_eh_try_stu use block timeout
  [SCSI] megaraid_sas: switch to block timeout
  [SCSI] ibmvscsi: switch to block timeout
  [SCSI] aacraid: switch to block timeout
  [SCSI] zfcp: prevent double decrement on host_busy while being busy
  [SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
  [SCSI] zfcp: eliminate race between validation and locking
  [SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
  [SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
  [SCSI] zfcp: Fix opening of wka ports
  [SCSI] zfcp: fix remote port status check
  [SCSI] fc_transport: fix old bug on bitflag definitions
  [SCSI] Fix hang in starved list processing

This fixes the MN10300 kernel module linking to match the toolchain.  RELA
relocs don't use the value at the location being relocated.  This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If xpc.ko and gru.ko are both statically linked into the kernel, then
xpc_init() can get called before gru_init() and make a call to one of the
gru's exported functions before the gru has initialized itself. The end
result is a NULL dereference.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id.  We were writing that directly
into the HW register.

We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Count the insertion of new pages in the statistics used to drive the
pageout scanning code.  This should help the kernel quickly evict
streaming file IO.

We count on the fact that new file pages start on the inactive file LRU
and new anonymous pages start on the active anon list.  This means
streaming file IO will increment the recent scanned file statistic, while
leaving the recent rotated file statistic alone, driving pageout scanning
to the file LRUs.

Pageout activity does its own list manipulation.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: Gene Heskett <gene.heskett@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Devices which share the same queue, like floppies and mtd devices, get
registered multiple times in the bdi interface, but bdi accounts only the
last registered device of the devices sharing one queue.

On remove, all earlier registered devices leak, stay around in sysfs, and
cause "duplicate filename" errors if the devices are re-created.

This prevents the creation of multiple bdi interfaces per queue, and the
bdi device will carry the dev_t name of the block device which is the
first one registered, of the pool of devices using the same queue.

[akpm@linux-foundation.org: add a WARN_ON so we know which drivers are misbehaving]
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The previous patch from Alan Cox ("nfsd: fix vm overcommit crash",
commit 731572d3) fixed the problem where
knfsd crashes on exported shmemfs objects and strict overcommit is set.

But the patch forgot supporting the case when CONFIG_SECURITY is
disabled.

This patch copies a part of his fix which is mainly for detecting a bug
earlier.
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Junjiro R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Another related 8390 driver. Since this is for nubus, not sure if
anyone still has the hardware?
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix build of ARM etherh driver with new net_device_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Fix this sparse warning:

  drivers/ide/alim15x3.c:594:2: warning: returning void-valued expression
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We guarantee 400ns delay at the time of issuing the command.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Also while at it:

* Drop unused arguments from ide_complete_power_step().

* Move DEBUG_PM printk() from ide_end_drive_cmd() to
  ide_complete_power_step().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Should fix kernel.org bug #10225:
http://bugzilla.kernel.org/show_bug.cgi?id=10225Reported-by: Matthias B. <haferfrost@web.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode.  In order to achieve this:

* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.

* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
  driver for nVidia controllers in Compatibility Mode.

* Teach actual_try_to_identify() and drive_is_ready() about the new flag.

This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).

[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
  and distributions use) it never worked correctly. ]

Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.

More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659
http://bugzilla.kernel.org/show_bug.cgi?id=10216Reported-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Lars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_release_lock() spits out lots of:

	ide_release_lock: bug

warnings on Atari Falcon.

Fix the ide_release_lock imbalance.
Signed-off-by: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't overflow the 16-character fb_fix_screeninfo id string (fixes some 
console erasing and blanking artifacts). Have the ID default to "Unknown" 
on machines with no built-in video and no nubus devices. Check for 
fb_alloc_cmap failure.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

We don't really have a max tx packet size limit, so allow configuring
the device with up to 64k tx MTU.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Based upon a lockdep report by Alexey Dobriyan.

I checked all per_cpu_counter_xxx() usages in network tree, and I
think all call sites are BH enabled except one in
inet_csk_listen_stop().

commit dd24c001
(net: Use a percpu_counter for orphan_count)
replaced atomic_t orphan_count to a percpu_counter.

atomic_inc()/atomic_dec() can be called from any context, while
percpu_counter_xxx() should be called from a consistent state.

For orphan_count, this context can be the BH-enabled one.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch provides the post-processing of feature negotiation state, after
the negotiation has completed.

To this purpose, handlers are used and added to the dccp_feat_table. Each
handler is passed a boolean flag whether the RX or TX side of the feature
is meant.

Several handlers are provided already, new handlers can easily be added.

The initialisation is now fully dynamic, i.e. CCIDs are activated only
after the feature negotiation. The integration of this dynamic activation
is done in the subsequent patches.

Thanks to Wei Yongjun for pointing out the necessity of skipping over empty
Confirm options while copying the negotiated feature values.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Analogous to the previous patch, this adds code to interpret incoming Confirm
feature-negotiation options. Both functions operate on the feature-negotiation
list of either the request_sock (server) or the dccp_sock (client).

Thanks to Wei Yongjun for pointing out that it is overly restrictive to check
the entire list of confirmed SP values.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds/replaces code for processing incoming ChangeL/R options.
The main difference is that:
 * mandatory FN options are now interpreted inside the function
  (there are too many individual cases to do this externally);
 * the function returns an appropriate Reset code or 0,
   which is then used to fill in the data for the Reset packet.

Old code, which is no longer used or referenced, has been removed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>