- 29 Aug, 2019 9 commits
-
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/ufs/ufs-qcom.c: In function ufs_qcom_pwr_change_notify: drivers/scsi/ufs/ufs-qcom.c:808:6: warning: variable val set but not used [-Wunused-but-set-variable] Fixes: 1e1e465c ("scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
zhengbin <zhengbin13@huawei.com> Acked-by:
Avri Altman <Avri.Altman@wdc.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Colin Ian King authored
There is a spelling mistake in a ql_log message. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function cq_interrupt_v1_hw: drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:1542:6: warning: variable irq_value set but not used [-Wunused-but-set-variable] Reported-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
Sreekanth Reddy authored
This patch provides a module parameter and sysfs interface to select whether the queue depth for each device should be based on the protocol-specific value set by the driver (the default) or the maximum supported by the controller (can_queue). Although we have a sysfs interface per sdev to change the queue depth of individual scsi devices, this implementation provides a single sysfs entry per shost to switch between the controller max and the driver default. [mkp: tweaked commit desc] Signed-off-by:
Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by:
-
Bart Van Assche authored
According to the firmware documentation a status type 0 IOCB can be followed by one or more status continuation type 0 IOCBs. Hence do not complain if the completion function is not called from inside the status type 0 IOCB handler. WARNING: CPU: 10 PID: 425 at drivers/scsi/qla2xxx/qla_isr.c:2784 qla2x00_status_entry.isra.7+0x484/0x17b0 [qla2xxx] CPU: 10 PID: 425 Comm: kworker/10:1 Tainted: G E 5.3.0-rc4-next-20190813-autotest-autotest #1 Workqueue: qla2xxx_wq qla25xx_free_rsp_que [qla2xxx] Call Trace: qla2x00_status_entry.isra.7+0x1484/0x17b0 [qla2xxx] (unreliable) qla24xx_process_response_queue+0x7d8/0xbd0 [qla2xxx] qla25xx_free_rsp_que+0x1a0/0x220 [qla2xxx] process_one_work+0x25c/0x520 worker_thread+0x8c/0x5e0 kthread+0x154/0x1a0 ret_from_kernel_thread+0x5c/0x7c Cc: Himanshu Madhani <hmadhani@marvell.com> Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Reported-by:
Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Tested-by:
Lee Duncan <lduncan@suse.com> Signed-off-by:
-
Stanley Chu authored
Currently bits in hba->outstanding_tasks are cleared only after their corresponding task management commands are successfully done by __ufshcd_issue_tm_cmd(). If timeout happens in a task management command, its corresponding bit in hba->outstanding_tasks will not be cleared until next task management command with the same tag used successfully finishes. This is wrong and can lead to some issues, like power issue. For example, ufshcd_release() and ufshcd_gate_work() will do nothing if hba->outstanding_tasks is not zero even if both UFS host and devices are actually idle. Solution is referred from error handling of device commands: bits in hba->outstanding_tasks shall be cleared regardless of their execution results. Signed-off-by:
Stanley Chu <stanley.chu@mediatek.com> Signed-off-by:
Chun-Hung Wu <chun-hung.wu@mediatek.com> Reviewed-by:
-
Colin Ian King authored
Pointer fh is being assigned a return value from the call to skb_transport_header however this value is never read and fh is being re-assigned immediately afterwards with a new value. Since there are side-effects from calling skb_transport_header the call is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by: -
Anil Varughese authored
Some UFS devices have issues if LCC is enabled. So we are setting PA_LOCAL_TX_LCC_Enable to 0 before link startup which will make sure that both host and device TX LCC are disabled once link startup is completed. Signed-off-by:
Anil Varughese <aniljoy@cadence.com> Reviewed-by:
Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by:
-
Colin Ian King authored
Variable error is being initialized with a value that is never read and error is being re-assigned a little later on. The assignment is redundant and hence can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:
-
- 20 Aug, 2019 31 commits
-
-
James Smart authored
Update lpfc version to 12.4.0.0 Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
-
James Smart authored
Currently, each hardware queue, typically allocated per-cpu, consists of a WQ/CQ pair per protocol. Meaning if both SCSI and NVMe are supported 2 WQ/CQ pairs will exist for the hardware queue. Separate queues are unnecessary. The current implementation wastes memory backing the 2nd set of queues, and the use of double the SLI-4 WQ/CQ's means less hardware queues can be supported which means there may not always be enough to have a pair per cpu. If there is only 1 pair per cpu, more cpu's may get their own WQ/CQ. Rework the implementation to use a single WQ/CQ pair by both protocols. Signed-off-by:
-
James Smart authored
FC-NVMe-2 added support for sequence level error recovery in the FC-NVME protocol. This allows for the detection of errors and lost frames and immediate retransmission of data to avoid exchange termination, which escalates into NVMeoFC connection and association failures. A significant RAS improvement. The driver is modified to indicate support for SLER in the NVMe PRLI is issues and to check for support in the PRLI response. When both sides support it, the driver will set a bit in the WQE to enable the recovery behavior on the exchange. The adapter will take care of all detection and retransmission. Signed-off-by:
-
James Smart authored
Typical SLI-4 hardware supports up to 2 4KB pages to be registered per XRI to contain the exchanges Scatter/Gather List. This caps the number of SGL elements that can be in the SGL. There are not extensions to extend the list out of the 2 pages. The G7 hardware adds a SGE type that allows the SGL to be vectored to a different scatter/gather list segment. And that segment can contain a SGE to go to another segment and so on. The initial segment must still be pre-registered for the XRI, but it can be a much smaller amount (256Bytes) as it can now be dynamically grown. This much smaller allocation can handle the SG list for most normal I/O, and the dynamic aspect allows it to support many MB's if needed. The implementation creates a pool which contains "segments" and which is initially sized to hold the initial small segment per xri. If an I/O requires additional segments, they are allocated from the pool. If the pool has no more segments, the pool is grown based on what is now needed. After the I/O completes, the additional segments are returned to the pool for use by other I/Os. Once allocated, the additional segments are not released under the assumption of "if needed once, it will be needed again". Pools are kept on a per-hardware queue basis, which is typically 1:1 per cpu, but may be shared by multiple cpus. The switch to the smaller initial allocation significantly reduces the memory footprint of the driver (which only grows if large ios are issued). Based on the several K of XRIs for the adapter, the 8KB->256B reduction can conserve 32MBs or more. It has been observed with per-cpu resource pools that allocating a resource on CPU A, may be put back on CPU B. While the get routines are distributed evenly, only a limited subset of CPUs may be handling the put routines. This can put a strain on the lpfc_put_cmd_rsp_buf_per_cpu routine because all the resources are being put on a limited subset of CPUs. Signed-off-by:
-
James Smart authored
Added code to support driver loopback with MDS Diagnostics. This style of diagnostics passes frames from the fabric to the driver who then echo them back out the link. SEND_FRAME WQEs are used to transmit the frames. Added the SOF and EOF field location definitions for use by SEND_FRAME. Also ensure that enable_mds_diags is a RW parameter. Signed-off-by:
-
James Smart authored
To aid better hardware detection when there are issues, report the first and second level hardware revisions from the READ_REV command. Add the elements to the existing hardware id string. Signed-off-by:
-
James Smart authored
In order to see real addresses, convert %p with %px for kernel addresses and replace %p with %pf for functions. While converting, standardize on "x%px" throughout (not %px or 0x%px). Signed-off-by:
-
James Smart authored
While performing code review, several relatively simple optimizations can be done in the fast path. Add these optimizations (unlikely designators). Signed-off-by:
-
James Smart authored
Running on Coverity produced the following errors: - coding style (indentation) - memset size mismatch errors note: comment cases where it is purposely a mismatch Fix the errors. Signed-off-by:
-
James Smart authored
modinfo for lpfc_nvme_enable_fb is incorrect. FirstBurst on lpfc target is not fully supported. Update the attribute description Signed-off-by:
-
James Smart authored
The driver is allowing the user to change lpfc_enable_bg while loading the driver against a FCoE adapter. This is not supported. No check is made for the adapter type when applying the blockguard enablement value. Fix by verifying the adapter type before setting the enablement flag. Signed-off-by:
-
James Smart authored
GetTrunkInfo is displaying an incorrect link speed when the link is a trunk and the link has gone down. The driver is not clearing the logical speed as part of the link down transition. Fix by setting the logical speed to UNKNOWN SPEED when the link goes down. Signed-off-by:
-
James Smart authored
Max Frame Size value is shown as 34816 in fdmishow from Switch. The driver uses bbRcvSize in common service param which is obtained from the READ_SPARM mailbox command. The bbRcvSize field which is displayed is a three nibble field but the driver is printing a full four nibbles. Fix by masking off the upper nibble. Signed-off-by:
-
James Smart authored
The scsi transport fc bsg interface does not expect the bsg_job_done() callback to be done if the bsg request call returns failure. Several of the HST_VENDOR cases in the driver unconditionally call bsg_job_done() regardless of the returning value. Fix the code to only call bsg_job_done() if the call to lpfc_bsg_request() will return success. Signed-off-by:
-
James Smart authored
When forcing the use of MSI (vs MSI-X) the driver is crashing in pci_irq_get_affinity. The driver was not using the new pci_alloc_irq_vectors interface in the MSI path. Fix by using pci_alloc_irq_vectors() with PCI_RQ_MSI in the MSI path. Signed-off-by:
-
James Smart authored
The driver is currently reporting a non-zero nvme sg_seg_cnt value of 256 when nvme is disabled. It should be zero. Fix by ensuring the value is cleared. Signed-off-by:
-
James Smart authored
If an unsolicited ABTS was received, the driver looks up the exchange it references. It it does various searches looking for the exchange context. When one is eventually matched and it is associated with an XRI context, the driver sends an ABORT WQE to terminate the exchange. Current code looks at whether the transport had taken action on the XRI yet or not (no action if set to LPFC_NVMET_STE_RCV; action if non-LPFC_NVMET_STE_RCV). Based on action or not one of two (sol vs unsol) issue abort routines are called. The unsol version cheats and transmits a sequence containing an ABTS with no interaction with the adapter. The sol version issues an Abort WQE and lets the adapter manage whether the ABTS is sent to not. The issue is the unsol version is sending ABTS unconditionally for the exchange that received the ABTS. It's unnecessary. Remove the conditional and just call the adapter command-based routine to let the adapter manage the ABTS. Signed-off-by:
-
James Smart authored
As part of firmware download, the adapter is reset. On the adapter the reset causes the function to stop and all outstanding io is terminated (without responses). The reset path then starts teardown of the adapter, starting with deregistration of the remote ports with the nvme-fc transport. The local port is then deregistered and the driver waits for local port deregistration. This never finishes. The remote port deregistrations terminated the nvme controllers, causing them to send aborts for all the outstanding io. The aborts were serviced in the driver, but stalled due to its state. The nvme layer then stops to reclaim it's outstanding io before continuing. The io must be returned before the reset on the controller is deemed complete and the controller delete performed. The remote port deregistration won't complete until all the controllers are terminated. And the local port deregistration won't complete until all controllers and remote ports are terminated. Thus things hang. The issue is the reset which stopped the adapter also stopped all the responses that would drive i/o completions, and the aborts were also stopped that stopped i/o completions. The driver, when resetting the adapter like this, needs to be generating the completions as part of the adapter reset so that I/O complete (in error), and any aborts are not queued. Fix by adding flush routines whenever the adapter port has been reset or discovered in error. The flush routines will generate the completions for the scsi and nvme outstanding io. The abort ios, if waiting, will be caught and flushed as well. Signed-off-by:
-
James Smart authored
This issue is specific to SLI-3 adapters, specifically when DIF is used. Once seen, this message floods the logs: 9064 BLKGRD: lpfc_scsi_prep_dma_buf_s3: Too many sg segments from dma_map_sg The driver, upon detecting an error such as too many elements in an sglist, misrepresents the error by treating it as a temporary resource issue by returning MLQUEUE_HOST_BUSY. In these cases, no retry will fix it and it should have been a hard error. The repeated retry was causing the spamming of the log. As for the initial reason of why an I/O encountered this issue at all is not clear as parameters set by the driver should have avoided this. The dm multipath maintainer has been notified of the issue. Fix by changing the return code for the dma mapping routines to indicate cases that are not retryable and return DID_ERROR on those cases. Signed-off-by:
-
James Smart authored
If the adapter encounters a condition which causes the adapter to fail (driver must detect the failure) simultaneously to a request to the driver to reset the adapter (such as a host_reset), the reset path will be racing with the asynchronously-detect adapter failure path. In the failing situation, one path has started to tear down the adapter data structures (io_wq's) while the other path has initiated a repeat of the teardown and is in the lpfc_sli_flush_xxx_rings path and attempting to access the just-freed data structures. Fix by the following: - In cases where an adapter failure is detected, rather than explicitly calling offline_eratt() to start the teardown, change the adapter state and let the later calls of posted work to the slowpath thread invoke the adapter recovery. In essence, this means all requests to reset are serialized on the slowpath thread. - Clean up the routine that restarts the adapter. If there is a failure from brdreset, don't immediately error and leave things in a partial state. Instead, ensure the adapter state is set and finish the teardown of structures before returning. - If in the scsi host reset handler and the board fails to reset and restart (which can be due to parallel reset/recovery paths), instead of hard failing and explicitly calling offline_eratt() (which gets into the redundant path), just fail out and let the asynchronous path resolve the adapter state. Signed-off-by:
-
James Smart authored
During cable pull testing a deadlock was seen between lpfc_nlp_counters() vs lpfc_mbox_process_link_up() vs lpfc_work_list_done(). They are all waiting on the shost->host_lock. Issue is all of these cases raise irq when taking out the lock but use spin_unlock_irq() when unlocking. The unlock path is will unconditionally re-enable interrupts in cases where irq state should be preserved. The re-enablement allowed the other paths to execute which then causes the deadlock. Fix by converting the lock/unlock to irqsave/irqrestore. Signed-off-by:
-
James Smart authored
In a test with high nvme remote port counts connected via a multi-hop FC switch config where switches were systematically reset (e.g. fabric partitioning and re-establishment), the nvme remote ports would switch addresses based on the switch reconfiguration events. The driver would get into a situation where the nvme port changed address, PLOGI and PRLI would succeed nvme transport registration occurred, but subsequent LS requests by the nvme subsystem failed due to a bad ndlp state and connectivity to the device failed. The driver hit a race condition on multiple devices that address swapped simultaneously. In cases where the driver notices the remote port structure came back as the same value as previously (meaning a nvme_rport structure was re-enabled and did not go through devloss_tmo/connect_tmo_failures on all controllers) the driver would unconditionally exit assuming the ndlp information was correct. But, if the ndlp's had been swapped, the ndlp had stale port state information, which when used by the LS request commands, would fail the commands. Fix by checking whether a node swap had occurred, and only exit if no ndlp swap had occurred. Signed-off-by:
-
James Smart authored
In situations where zoning is not being used, thus NVMe initiators see other NVMe initiators as well as NVMe targets, a link bounce on an initiator will cause the NVMe initiators to spew "6169" State Error messages. The driver is not qualifying whether the remote port is a NVMe targer or not before calling the lpfc_nvme_rescan_port(), which validates the role and prints the message if its only an NVMe initiator. Fix by the following: - Before calling lpfc_nvme_rescan_port() ensure that the node is a NVMe storage target or a NVMe discovery controller. - Clean up implementation of lpfc_nvme_rescan_port. remoteport pointer will always be NULL if a NVMe initiator only. But, grabbing of remoteport pointer should be done under lock to coincide with the registering of the remote port with the fc transport. Signed-off-by:
-
James Smart authored
On an SLI-3 adapter which does not support NVMe, but with the driver global attribute to enable nvme on any adapter if it does support NVMe (e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE values are being munged by the protocol enablement when it shouldn't be. Correct by changing the location of where the NVME sgl information is being applied, which will avoid any SLI-3-based adapter. Signed-off-by:
-
James Smart authored
If admin changes the devloss_tmo on an rport via the fc_remote_port rport dev_loss_tmo attribute, the value is on set on scsi stack. The change is not propagated to NVMe. The set routine in the lldd lacks the call to nvme_fc_set_remoteport_devloss() to set the value. Fix by adding the call to the lldd set routine. Signed-off-by:
-
James Smart authored
In tests with remote ports contantly logging out/logging coupled with occassional local link bounce, if a remote port is disocnnected for longer than devloss_tmo and then subsequently reconnected, eventually the test will fail to login with the remote port and remote port connectivity is lost. When devloss_tmo expires, the driver does not free the node struct until the port or npiv instances is being deleted. The node is left allocated but the state set to UNUSED. If the node was in the process of logging in when the local link drop occurred, meaning the RPI was allocated for the node in order to send the ELS, but not yet registered which comes after successful login, the node is moved to the NPR state, and if devloss expires, to UNUSED state. If the remote port comes back, the node associated with it is restarted and this path happens to allocate a new RPI and overwrites the prior RPI value. In the cases where the port was logged in and loggs out, the path did release the RPI but did not set the node rpi value. In the cases where the remote port never finished logging in, the path never did the call to release the rpi. In this latter case, when the node is subsequently restore, the new rpi allocation overwrites the rpi that was not released, and the rpi is now leaked. Eventually the port will run out of RPI resources to log into new remote ports. Fix by following changes: - When an rpi is released, do so under locks and ensure the node rpi value is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note: refactored to a small service routine to avoid indentation issues. - When re-enabling a node, check the rpi value to determine if a new allocation is necessary. If already set, use the prior rpi. Enhanced logging to help in the future. Signed-off-by:
-
James Smart authored
If a remote port is removed and remains removed for devloss_tmo, if an RSCN is subsequently received indicating the presence of the remte port, the driver does not login to and rediscovery the remote port. Currently, in order to for a port to be rediscovered post an RSCN, the node state must be NPR to reflect not logged in. When devloss expires, the node state is marked UNUSED. When an RSCN occurs, the nodes referenced by the RSCN will have a NPR_2B_DISC flag set, but the re-login will only be attempted if the node is in NPR_NODE state. Thus the node is skipped over. Fix by recognizing the NPR_2B_DISC and UNUSED and transition the node back to NPR state to allow the re-login to take place. Signed-off-by:
-
James Smart authored
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will oops. Coding of a loop allowed a new value (rport) to be set/checked for null followed by an older value (remoteport) checked for null to allow progress where the new value, even though null, will be referenced. Rework the logic to validate and prevent any reference to the null ptr. Signed-off-by:
-
James Smart authored
It's possible for the driver to initiate an FLOGI and before it completes, another link down/up transition occurs requiring a new FLOGI. Currently, nothing is done to abort/noop the older FLOGI request to the adapter, so if this transition occurs and the FLOGI completion is received after the link down/up transition, the driver may erroneously act on the older FLOGI. In most cases, the adapter properly terminates/fails the FLOGI, but there is a timing condition where the FLOGI may complete on the wire prior to the transition, but the response may not be seen/processed by the driver before the driver sees the link transition. Fix by having the link down handler in the driver run through any outstanding ELS's and change the completion handler of the ELS so that it will be no-op'd and released. Signed-off-by:
-
James Smart authored
When tearing down the adapter for a reset, online/offline, or driver unload, the queue free routine would hit a GPF oops. This only occurs on conditions where the number of hardware queues created is fewer than the number of cpus in the system. In this condition cpus share a hardware queue. And of course, it's the 2nd cpu that shares a hardware that attempted to free it a second time and hit the oops. Fix by reworking the cpu to hardware queue mapping such that: Assignment of hardware queues to cpus occur in two passes: first pass: is first time assignment of a hardware queue to a cpu. This will set the LPFC_CPU_FIRST_IRQ flag for the cpu. second pass: for cpus that did not get a hardware queue they will be assigned one from a primary cpu (one set in first pass). Deletion of hardware queues is driven by cpu itteration, and queues will only be deleted if the LPFC_CPU_FIRST_IRQ flag is set. Also contains a few small cleanup fixes and a little better logging. Signed-off-by:
-
James Smart authored
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with irq. But, the path is already under the hbalock which raised irq so it's unnecessary. Convert to simple lock/unlock. Signed-off-by:
-
