- 30 Nov, 2011 34 commits
-
-
Axel Lin authored
It is not used outside this driver so no need to make the symbol global. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Dan Carpenter authored
We should free "bus_if" here, it's a small leak but it makes the static checkers happy. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
here we check for BT state and if BT calibration has started, give 25ms for BT Calibration to finish. we also take care of 2G/5G switch and LNA transfer incase WLAN is operating in 5G. in case the BT state is awake when we do WLAN calibration re-calibrate and we reset the message exchange between WLAN and BT. BT is given preference when simultaneous CAL request happens. calibration for WLAN/BT is done assuming that the other co-existing module is in awake state, if not we continue to do calibration while if the other module's state changes we need to do restart the calibration handshake Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
WLAN communicates with BT for its calibration by sending WLAN_CAL_REQ, waits for BT_CAL_GRANT. This is done with the help of GPM messages. also WLAN_CAL_DONE messages is sent once WLAN calibration is done. Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
send halt BT GPM if the chip is in network sleep and BT state is awake Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
required buffers and dma allocation is done for GPM and SCHED messages Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
check for the condition of MCI interrupt being triggered and appropriately obtain the values of MCI_INTERRUPT_RX_MSG_RAW and MCI_INTERRUPT_RAW Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
MCI interrupt is an asynchronous one, so take care of it by having a check in ath9k_hw_intrpend, which actually decides whether the interrupt is really for the driver from ath_isr Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
enable MCI interrupt when ath9k_hw_enable_interrupts is called, like during the completion of chip_reset before which the interrupts are disabled Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
these parameter will be utilized and modified in the MCI hardware codes state machine Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
these definitions will be used by MCI state machine and the corresponding hardware code Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Joe Perches authored
Logging messages that mimic function tracer enter/exit aren't necessary. Just remove them. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Joe Perches authored
All uses have been removed, so killing what's not necessary. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Joe Perches authored
Using the standard debugging mechanisms is better than subsystem specific ones when the subsystem doesn't use a specific struct. Coalesce long formats. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Joe Perches authored
Using the normal logging styles is preferred over subsystem specific styles when the subsystem does not take a specific struct. Convert nfc_<level> specific messages to pr_<level> Add newlines to uses. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
As of hostap_0_7_1~358 the CONFIG_DRIVER_PRISM54 was removed from upstream wpa_supplicant/hostapd so lets just kill the useless old prism54 private ioctl crap. Cc: Jouni Malinen <j@w1.fi> Cc: David Miller <davem@davemloft.net> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
change the AR_DEF_ANTENNA register settings i.e setting default antenna setting only for antenna diversity enabled chipsets. no point in doing this for MIMO chipsets Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
GPIO pin 4 is assigned AR9462 chipsets LED. while GPIO pin 0 worked for obselete AR9462 chipsets though they are meant for EEPROM as per Russell Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Russell Hu <rhu@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Mohammed Shafi Shajakhan authored
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The on-channel work optimisations have caused a number of issues, and the code is unfortunately very complex and almost impossible to follow. Instead of attempting to put in more workarounds let's just remove those optimisations, we can work on them again later, after we change the whole auth/assoc design. This should fix rate_control_send_low() warnings, see RH bug 731365. Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
mBm is passed but dBm was assumed... Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
Both cases are doing the same so treat the switch cases for both as an "or". Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
mBm is passed but dBm was assumed... Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
Tons of drivers missed that we use mBm and not dBm... Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Axel Lin authored
This patch converts the drivers in net/rfkill/* to use the module_platform_driver() macro which makes the code smaller and a bit simpler. Cc: "David S. Miller" <davem@davemloft.net> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Antonio Ospite <ospite@studenti.unina.it> Cc: Rhyland Klein <rklein@nvidia.com> Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Rhyland Klein <rklein@nvidia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
- 28 Nov, 2011 6 commits
-
-
Emmanuel Grumbach authored
Add more data when inconsistencies occur in the AGG state machine. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
Not sure it is the best way to do it, but many times we want to know what the configuration options were enabled for the compiled driver. Let's just log the options during load time; so there were be no confusion. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Wey-Yi Guy authored
missing the string, add it Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
Since the uCode hasn't been released (yet?), warn only if using older than API 4, but load anything up to API 6. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
This makes handling the calibration data more generic and no longer requires updating IWL_CALIB_MAX when a new uCode comes with more calibration packets. Since we just copy the data back, there's also no need for understanding which calibration we received -- we can just reflect it back to the runtime uCode. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The init microcode knows very well which calibrations are required and sends us results for those that are. Consequently, we can just send all of those to the RT uCode again. The problem with having the driver know about this is that it is a uCode feature, not a hardware feature so the config is completely unsuitable. The only thing we need to check is whether the device needs crystal calibration or not, add a new parameter to the configuration for that. This makes new uCode work on 6000 series devices. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-