Add support for indicating the availability of dedicated lines for
RTS/CTS hardware flow control, using the standard "uart-has-rtscts" DT
property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The existing support for hardware-assisted RTS/CTS is rudimentary and
doesn't work.

Add support for hardware-assisted RTS/CTS hardware flow control for the
(H)SCIF, SCIFA, and SCIFB variants.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Before, the driver relied on initialization by the boot loader, or by
implicit reset state.

Note that unlike on (H)SCIF, the RTS/CTS bits exist only if dedicated
RTS/CTS pins are available, which depends on the SoC and UART instance.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct pin initialization on (H)SCIF:
  - RTS must be deasserted (it's active low),
  - SCK must be an input, as it may be used as the optional external
    clock input.

Initial pin configuration must always be done:
  - Regardless of the presence of dedicated RTS and CTS pins: if the
    register exists, the RTS/CTS bits exist, too,
  - Regardless of hardware flow control being enabled or not: RTS must
    be deasserted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Improve documentation for the SCIFA/SCIFB Serial Port Control and Data
Registers:
  - State clearly that the RTS and CTS lines are active-low,
  - Document the bits related to the serial port's SCK, RXD, and TXD
    pins.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Improve documentation for the (H)SCIF Serial Port Register:
  - Make it clear the RTS and CTS lines are active-low,
  - Document the bits related to the serial port's clock pin.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace open-coded variants of sci_getreg() by function calls, and drop
intermediate variables where appropriate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enhance the Renesas SCI UART driver to add support for GPIO-controlled
modem lines (CTS, DSR, DCD, RNG, RTS, DTR), using the serial_mctrl_gpio
helpers.

GPIO-controlled modem lines can be used when dedicated modem lines are
not available. Invalid configurations specifying both GPIO RTS/CTS and
dedicated RTS/CTS are rejected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/serial/driver clearly states:

    If the port does not support CTS, DCD or DSR, the driver should
    indicate that the signal is permanently active.

Hence always set TIOCM_CTS, as we currently don't look at the CTS
hardware line state at all.

FWIW, this fixes the transmit path when hardware-assisted flow control
is enabled, and userspace enables CRTSCTS.
The receive path is still broken, as RTS is never asserted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some Renesas SCIF UARTs have dedicated lines for RTS/CTS hardware flow
control.  Whether these lines exist depends on SoC and UART instance
inside the SoC.  Whether these lines can be used for hardware flow
control depends on board wiring.

Amend the DT bindings with an optional property to indicate that RTS/CTS
hardware flow control lines exist, and can be used as such, according to
the Generic Serial DT Bindings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Amend the DT bindings for the Renesas SCI driver to allow describing
optional GPIO-controlled modem lines, which can be used where dedicated
modem lines are not available.

The property naming is dictated by the Generic Serial DT Bindings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vc_deccolm is only set and never read, remove the member from vc_data.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We do not do hashtables for unicode fonts since 1995 (1.3.28). So it
is time to remove the second parameter of con_clear_unimap and ignore
the advice from userspace completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Namely convert:
* IS_FG -> con_is_fg
* DO_UPDATE -> con_should_update
* CON_IS_VISIBLE -> con_is_visible

DO_UPDATE was a weird name for a yes/no answer, so the new name is
con_should_update.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Flush the switch cases to be aligned with the switch. Mostly
everything can now fit to the 80-chars terminal.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Do not opencode max3, use the macro.

Separate commands. Until now, I have not noticed the comma. Make it
one line, one command. And make the code obvious.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The compiler noticed passing structure over stack. Even though rgb is
a small structure, let us define one and pass that over all the
functions wherever needed.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code with T.416 high colors handling is flushed to the right and
hard to read. Move the code to a separate function and remove code
duplication for foreground & background colors.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's a macro accessing and changing some local variables. And the code
uses it without appending semicolon which confuses everybody too.

Switch from this bad guy to a sane standard function.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is never defined. And I spent quite some time looking into the
history and cannot find how this was ever used. Given it was not used
in the history, I doubt it currently works as expected after the years
of changes all over the code.

So kill it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is never called since commit 81732c3b (tty vt: Fix line
garbage in virtual console on command line edition) in 3.7. So remove
all the callbacks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: linux-usb@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* allow NULL consw->con_set_palette (some consoles define an empty
  hook)
* => remove empty hooks now
* return value of consw->con_set_palette is never checked => make the
  function void
* document consw->con_set_palette a bit
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: linux-usb@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

* allow NULL consw->con_scrolldelta (some consoles define an empty
  hook)
* => remove empty hooks now
* return value of consw->con_scrolldelta is never checked => make the
  function void
* document consw->con_scrolldelta a bit
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: linux-usb@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bytes_written parameter of sisusb_copy_memory and sisusb_read_memory
is an out parameter, but its value is never used. So remove it and
pass a dummy variable down to sisusb_read_mem_bulk.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All those members of vc_data are each explained in short. But it needs
an example for one to understand the whole picture.

So add an ascii art depicting the most important vc_data members.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is always called with 0, so remove the parameter and pass the
default down to scrolldelta without checking.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The compiler complains about variables that are set, but never used:
* intX variables in exar_handle_irq
  drivers/tty/serial/8250/8250_port.c:1864:34: warning: variable ‘int3’ set but not used [-Wunused-but-set-variable]
* val variable in pci_quatech_wqopr
  drivers/tty/serial/8250/8250_pci.c:1139:10: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]

And about a shadow variable:
* tmout in wait_for_xmitr is defined twice with the same type. Both of
  them are also initialized before use.

Remove all of them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform_get_irq can fail, so we should handle negative value when
returned.

[v2]

platform_get_irq can actually return zero on some platforms. So do not
remove checks for irq == 0 there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert DEBUG_INTR to pr_debug:
* defined semantics (DEBUG, DYNAMIC_DEBUG)
* KERN_DEBUG level instead of KERN_DEFAULT
* emit __func__ and \n
* verified 'fmt' even when !DEBUG

I wonder if anybody ever used that or whether we should just drop the
lines.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hub6 and irqflags from struct old_serial_port are nowhere set. Drop
them from the structure and replace the reads by zeros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

STD_COM_FLAGS is mostly a bad name for what the drivers thinks it is.
Stop using it and pass the flags directly.

cyclades defines it as 0, so we do not assign anything to freshly
tty_port_init'ed structure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

STD_COM_FLAGS needs not be defined as it is not used anywhere on frv.

SERIAL_PORT_DFNS is defined to be empty. 8250 is aware of empty
SERIAL_PORT_DFNS and does:
 #ifndef SERIAL_PORT_DFNS
 #define SERIAL_PORT_DFNS
 #endif

So no need to define it on frv.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Do not initialize members of initialized structures to zero. They are
zeroed automatically.

Part of hub6 cleanup series.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In ircomm_tty_get_serial_info, struct serial_struct is memset to 0 and
then some members set to 0 explicitly.

Remove the latter as it is obviously superfluous.

And remove the retinfo check against NULL. copy_to_user will take care
of that.

Part of hub6 cleanup series.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Samuel Ortiz <samuel@sortiz.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In ipwireless_get_serial_info, struct serial_struct is memset to 0 and
then some members set to 0 explicitly.

Remove the latter as it is obviously superfluous.

And remove the retinfo check against NULL. copy_to_user will take care
of that.

Part of hub6 cleanup series.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Kosina <jikos@kernel.org>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull UDF fixes and a reiserfs fix from Jan Kara:
 "A couple of udf fixes (most notably a bug in parsing UDF partitions
  which led to inability to mount recent Windows installation media) and
  a reiserfs fix for handling kstrdup failure"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  reiserfs: check kstrdup failure
  udf: Use correct partition reference number for metadata
  udf: Use IS_ERR when loading metadata mirror file entry
  udf: Don't BUG on missing metadata partition descriptor

Pull dmaengine fixes from Vinod Koul:
 "Some fixes has piled up, so time to send them upstream.

  These fixes include:
   - at_xdmac fixes for residue and other stuff
   - update MAINTAINERS for dma dt bindings
   - mv_xor fix for incorrect offset"

* tag 'dmaengine-fix-4.7-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mv_xor: Fix incorrect offset in dma_map_page()
  dmaengine: at_xdmac: double FIFO flush needed to compute residue
  dmaengine: at_xdmac: fix residue corruption
  dmaengine: at_xdmac: align descriptors on 64 bits
  MAINTAINERS: Add file patterns for dma device tree bindings

Pull ARM SoC fixes from Olof Johansson:
 "Another batch of fixes for ARM SoC platforms.  Most are smaller fixes.

  Two areas that are worth pointing out are:

   - OMAP had a handful of changes to voltage specs that caused a bit of
     churn, most of volume of change in this branch is due to this.

   - There are a couple of _rcuidle fixes from Paul that touch common
     code and came in through the OMAP tree since they were the ones who
     saw the problems.

 The rest is smaller changes across a handful of platforms"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
  ARM: dts: STi: stih407-family: Disable reserved-memory co-processor nodes
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  arm: Use _rcuidle for smp_cross_call() tracepoints
  MAINTAINERS: Add myself as reviewer of ARM FSL/NXP
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
  ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
  ARM: imx6ul: Fix Micrel PHY mask
  ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
  ARM: dts: DRA74x: fix DSS PLL2 addresses
  ARM: OMAP2: Enable Errata 430973 for OMAP3
  ARM: dts: socfpga: Add missing PHY phandle
  ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board
  ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board
  ARM: dts: sun6i: yones-toptech-bs1078-v2: Drop constraints on dc1sw regulator
  ARM: dts: sun6i: primo81: Drop constraints on dc1sw regulator
  ARM: dts: sunxi: Add OLinuXino Lime2 eMMC to the Makefile
  ...

OMAP-GPMC: Fixes for for v4.7-rc cycle:

- Fix omap gpmc EXTRADELAY timing. The DT provided timings
were wrongly used causing devices requiring extra delay timing
to fail.

* tag 'gpmc-omap-fixes-for-v4.7' of https://github.com/rogerq/linux:
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  + Linux 4.7-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>