This commit documents bindings to be added to the eeprom_93xx46 driver
which will allow:

  - Device word size and read-only attributes to be specified.
  - A device-specific compatible string for use with Atmel AT93C46D
    EEPROMs.
  - Specifying a GPIO line to function as a 'select' or 'enable' signal
    prior to accessing the EEPROM.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Chris Healy <chris.healy@zii.aero>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Compatible at93xx46 devices from both Microchip and Atmel expect a
word-based address, regardless of whether the device is strapped for 8-
or 16-bit operation.  However, the offset parameter passed in when
reading or writing at a specific location is always specified in terms
of bytes.

This commit fixes 16-bit read and write accesses by shifting the offset
parameter to account for this difference between a byte offset and a
word-based address.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Tested-by: Chris Healy <chris.healy@zii.aero>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No need to use use continuous memory, it may be fail
when memory deeply fragmented.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Xia Qing <saberlily.xia@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Compat ioctl is already introduced in drivers/char/ppdev.c in order to
fix y2038 issue for PP[GS]ETTIME. There is no need to define these
here.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The arg of ioctl in ppdev is the pointer of integer except the
timeval in PPSETTIME, PPGETTIME. Different size of timeval
is already supported by the previous patches. So, it is safe
to add compat support.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The y2038 issue for ppdev is changes of timeval in the ioctl
(PPSETTIME and PPGETTIME). The size of struct timeval changes from
8bytes to 16bytes due to the changes of time_t. It lead to the
changes of the command of ioctl, e.g. for PPGETTIME, We have:

on 32-bit (old): 0x80087095
on 32-bit (new): 0x80107095
on 64-bit      : 0x80107095

This patch define these two ioctl commands to support the 32bit
and 64bit time_t application at the same time. And, introduce
pp_set_timeout to remove some duplicated code.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Simplify a few of the *generic* shared dev_warn() and dev_dbg()
print messages for three reasons:

0) Historically firmware_class code was added to help
   get device driver firmware binaries but these days
   request_firmware*() helpers are being repurposed for
   general *system data* needed by the kernel.

1) This will also help generalize shared code as much as possible
   later in the future in consideration for a new extensible firmware
   API which will enable to separate usermode helper code out as much
   as possible.

2) Kees Cook pointed out the the prints already have the device
   associated as dev_*() helpers are used, that should help identify
   the user and case in which the helpers are used. That should provide
   enough context and simplifies the messages further.

v4: generalize debug/warn messages even further as suggested by
    Kees Cook.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Vojtěch Pavlík <vojtech@suse.cz>
Cc: Kyle McMartin <kyle@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Removed braces from single statement if condition.Fixed checkpatch.pl
warning.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some array of const char are not set as const.
This patch fix that.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for more than 128 peripherals by taking a lazy
caching approach to the mapping tables. Instead of reading and
caching the tables at boot given some fixed size, read them and
cache them on an as needed basis. We still assume a max size of
512 peripherals, trading off some space for simplicity.

Based on a patch by Gilad Avidov <gavidov@codeaurora.org> and
Sagar Dharia <sdharia@codeaurora.org>.

Cc: Gilad Avidov <gavidov@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hdq_usecount was set to zero after a successful read, so
omap_hdq_put could not properly free resources which leads
e.g. to increasing usecounts in lsmod output
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1) Make the include file to sort from order
2) clean up the driver to make more readability

Let's clean up such trivial details.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

this pacthset try to fix the code style for sunxi.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem providers have restrictions on register strides, so return error
when users attempt to read/write buffers with sizes which are less
than word size.

Without this patch the userspace would continue to try as it does not
get any error from the nvmem core, resulting in a hang or endless loop
in userspace.
Reported-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add Mediatek EFUSE driver to access hardware data like
thermal sensor calibration or HDMI impedance.
Signed-off-by: Andrew-CT Chen <andrew-ct.chen@mediatek.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add Mediatek MT8173 EFUSE Devicetree binding file
Signed-off-by: Andrew-CT Chen <andrew-ct.chen@mediatek.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds support for NXP LPC18xx EEPROM memory found in NXP
LPC185x/3x and LPC435x/3x/2x/1x devices.

EEPROM size is 16384 bytes and it can be entirely read and
written/erased with 1 word (4 bytes) granularity. The last page
(128 bytes) contains the EEPROM initialization data and is not writable.

Erase/program time is less than 3ms. The EEPROM device requires a
~1500 kHz clock (min 800 kHz, max 1600 kHz) that is generated dividing
the system bus clock by the division factor, contained in the divider
register (minus 1 encoded).

EEPROM will be kept in Power Down mode except during read/write calls.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the devicetree binding document for NXP LPC18xx EEPROM memory.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_i2c_client() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 985087db 'misc: add support for bmp18x chips to the bmp085
driver' changed the BMP085 config symbol to a boolean.  I see no
reason why the shared code cannot be built as a module, so change it
back to tristate.

Fixes: 985087db ("misc: add support for bmp18x chips to the bmp085 driver")
Cc: Eric Andersson <eric.andersson@unixphere.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

drivers/misc/Kconfig:config ARM_CHARLCD
drivers/misc/Kconfig:   bool "ARM Ltd. Character LCD Driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and this driver did not have a ".remove"
function coded for non-modular drivers either.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

We don't replace module.h with init.h since the file already has that.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow the pch_phub driver to be build on MIPS platforms, in preparation
for its use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The pr_debug() will never be executed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of calling release_firmware() on every error and then jumping
lets have a common release_firmware() in the error path.
This patch also fixes a memory leak where we missed release_firmware()
if mic_x100_load_command_line() fails.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of jumping to a label and then returning from there lets return
directly.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If request_firmware() succeeds then rc becomes 0. After that if the test
for strcmp() fails then we were jumping to label done: and returning rc.
But rc being 0 we returned success whereas we have failed here and we
were supposed to return an error.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

>From the error path we are printing an error message with dev_err(). No
need to print almost same message with dev_dbg().
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After the loop we test "if (!retry)" to see if we timedout.  The problem
is "retry--" is a post-op so retry will be -1 at the end of the loop.  I
have fixed this by changing it to a pre-op instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following crash seen when MIC reset is invoked in
RESET_FAILED state due to device_del being called a second time on an
already deleted device:

[<ffffffff813b2295>] device_del+0x45/0x1d0
[<ffffffff813b243e>] device_unregister+0x1e/0x60
[<ffffffffa040f1c2>] scif_unregister_device+0x12/0x20 [scif_bus]
[<ffffffffa042f75a>] cosm_stop+0xaa/0xe0 [mic_cosm]
[<ffffffffa042f844>] cosm_reset_trigger_work+0x14/0x20 [mic_cosm]

The fix consists in realizing that because cosm_reset changes the
state to MIC_RESETTING, cosm_stop needs the previous state, before it
changed to MIC_RESETTING, to decide whether a hw_ops->stop had
previously been issued. This is now provided in a new cosm_device
member cdev->prev_state.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds Intel(R) Trace Hub PCI ID for Broxton SOC.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds Intel(R) Trace Hub PCI ID for Apollo Lake SOC.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, the character device write method allocates a temporary buffer
for user's data, but the user's data size is not sanitized and can cause
arbitrarily large allocations via kzalloc() or an integer overflow that
will then result in overwriting kernel memory.

This patch trims the input buffer size to avoid these issues.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>