Enabling CONFIG_DEBUG_ATOMIC_SLEEP has shown that some rfcomm functions
acquiring spinlocks call sleeping locks further in the chain.  Converting
the offending spinlocks into mutexes makes sleeping safe.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

H4 states are not used anymore.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Change subcmd parameter from int to u8 to match its use:
btmrvl_send_sync_cmd(priv, BT_CMD_MODULE_CFG_REQ, &subcmd, 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The HCISETRAW ioctl command is not really useful. To utilize raw and
direct access to the HCI controller, the HCI User Channel feature has
been introduced. Return EOPNOTSUPP to indicate missing support for
this command.

For legacy reasons hcidump used to use HCISETRAW for permission check
to return proper error codes to users. To keep backwards compability
return EPERM in case the caller does not have CAP_NET_ADMIN capability.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The GAP Specification gives the flexibility to decide whether MITM
Protection is requested or not (Bluetooth Core Specification v4.0
Volume 3, part C, section 6.5.3) when replying to an
HCI_EV_IO_CAPA_REQUEST event.

The recommendation is *not* to set this flag "unless the security
policy of an available local service requires MITM Protection"
(regardless of the bonding type). However, the kernel doesn't
necessarily have this information and therefore the safest choice is
to always use MITM Protection, also for General Bonding.

This patch changes the behavior for the General Bonding initiator
role, always requesting MITM Protection even if no high security level
is used. Depending on the remote capabilities, the protection might
not be actually used, and we will accept this locally unless of course
a high security level was originally required.

Note that this was already done for Dedicated Bonding. No-Bonding is
left unmodified because MITM Protection is normally not desired in
these cases.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When responding to a remotely-initiated pairing procedure, a MITM
protected SSP associaton model can be used for pairing if both local
and remote IO capabilities are set to something other than
NoInputNoOutput, regardless of the bonding type (Dedicated or
General).

This was already done for Dedicated Bonding but this patch proposes to
use the same policy for General Bonding as well.

The GAP Specification gives the flexibility to decide whether MITM
Protection is used ot not (Bluetooth Core Specification v4.0 Volume 3,
part C, section 6.5.3).

Note however that the recommendation is *not* to set this flag "unless
the security policy of an available local service requires MITM
Protection" (for both Dedicated and General Bonding). However, as we are
already requiring MITM for Dedicated Bonding, we will follow this
behaviour also for General Bonding.
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Do not always set the MITM protection requirement by default in the
field conn->auth_type, since this will be added later in
hci_io_capa_request_evt(), as part of the requirements specified in
HCI_OP_IO_CAPABILITY_REPLY.

This avoids a hackish exception for the auto-reject case, but doesn't
change the behavior of the code at all.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Refactor the code without changing its behavior by handling the
no-bonding cases first followed by General Bonding.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When sending out a device found event caused by an advertising report in
the situation where we couldn't store the report as a pending one, the
code was incorrectly trying to use the address and address type from the
pending data. Since the pending data is cleared in the previous line
this causes a potentially incorrect address type and an address of
BDADDR_ANY. This patch fixes the call to use the address information
correctly from the received advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

For SD8897, CMD52 write_to_clear may have missing interrupts
under certain corner case condition. Use CMD53 read-to-clear
to fix the problem.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

To be consistent, lets use msec for this timeout as well.

Note: This define value is a minimum scan time taken from BT Core spec 4.0,
Vol 3, Part C, chapter 9.2.6
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

With this patch it is possible to control discovery interleaved
timeout value from debugfs.

It is for fine tuning of this timeout.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Keep msec instead of jiffies in this define. This is needed by following
patch where we want this timeout to be exposed in debugfs.

Note: Value of this timeout comes from recommendation in BT Core Spec.4.0,
Vol 3, Part C, chapter 13.2.1.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch improves readability and makes future changes easier.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The ssp parameter is supposed to be a mandatory one and there are no
callers that would pass NULL to this function. Removing this unnecessary
NULL check also makes (false positive) static analyzer warnings go away.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When sending a pending device found event triggered by disabling LE
scanning we should use the stored RSSI instead of sending a zero value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Especially in crowded environments it can become frequent that we have
to send out whatever pending event there is stored. Since user space
has its own filtering of small RSSI changes sending a 0 value will
essentially force user space to wake up the higher layers (e.g. over
D-Bus) even though the RSSI didn't actually change more than the
threshold value.

This patch adds storing also of the RSSI for pending advertising reports
so that we report an as accurate RSSI as possible when we have to send
out the stored information to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Occasionally, during active scanning we will receive duplicate ADV_IND
reports from the same device before receiving the SCAN_RSP from them. In
order to not wake up user space unnecessarily it's better not to send
these extra events as they do not contain any new information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The line was incorrectly split between the variable type and its name.
This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

All callers of hci_inquiry_cache_update() pass a non-NULL ssp pointer to
it and even the function itself assumes in another place that the
pointer is non-NULL. Therefore, remove the redundant check.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

To avoid too many events being sent to user space and to help parsing of
all available remote device data it makes sense for us to wait for the
scan response and send a single merged Device Found event to user space.

This patch adds a few new variables to hci_dev to track the last
received ADV_IND/ADV_SCAN_IND, i.e. those which will cause a SCAN_REQ to
be send in the case of active scanning. When the SCAN_RSP is received
the pending data is passed together with the SCAN_RSP to the
mgmt_device_found function which takes care of merging them into a
single Device Found event.

We also need a bit of extra logic to handle situations where we don't
receive a SCAN_RSP after caching some data. In such a scenario we simply
have to send out the pending data as it is and then operate on the new
report as if there was no pending data.

We also need to send out any pending data when scanning stops as
well as ensure that the storage is empty at the start of a new active
scanning session. These both cases are covered by the update to the
hci_cc_le_set_scan_enable function in this patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When we're in peripheral mode (HCI_ADVERTISING flag is set) the most
natural mapping of connect() is to perform directed advertising to the
peer device.

This patch does the necessary changes to enable directed advertising and
keeps the hci_conn state as BT_CONNECT in a similar way as is done for
central or BR/EDR connection initiation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In preparation for being able to merge ADV_IND/ADV_SCAN_IND and SCAN_RSP
together into a single device found event add a second parameter to the
mgmt_device_found function. For now all callers pass NULL as this
parameters since we don't yet have storing of the last received
advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Passive LE scanning is only used by the kernel-internal connection
establishment procedure. It makes therefore little sense to send device
found events to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When a timeout occurs using directed advertising a 0x3c error gets
generated. Since the operation is analogous to conventional connection
creation map this to the usual EHOSTDOWN error.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Once directed advertising is brought into the picture simply the lack of
an hci_conn object when an le_conn_complete event occurs is no longer a
reliable indication that the responder & initiator values need to be
set based on our advertising address type.

This patch moves the code for setting these values outside of the
"if (!conn)" branch and ensures that they get set for any connection
where we are in the slave role.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Any time hci_conn_add is used for an LE connection we need to ensure
that the local identity address is correctly described in the src and
src_type variables. This patch moves setting these values directly into
hci_conn_add so that callers don't have to duplicate the effort
themselves.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch does a small code simplification replacing the tipical
kmalloc-copy_from_user sequence by memdup_user() helper.

Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

As preparation for merging ADV_IND/ADV_SCAN_IND and SCAN_RSP together
into a single mgmt Device Found event refactor individual advertising
report handling into a separate function. This will help keep the code
more readable as more logic gets added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We should let user space request the peer address also in the pending
connect states, i.e. BT_CONNECT and BT_CONNECT2. There is existing user
space code that tries to do this and will fail without extending the set
of allowed states for the peer address information.

This patch adds the two states to the allowed ones in the L2CAP and
RFCOMM sock_getname functions, thereby preventing ENOTCONN from being
returned.
Reported-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The smp variable in smp_conn_security is not used anywhere before the
smp = smp_chan_create() call in the smp_conn_security function so it
makes no sense to assign any other value to it before that.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The smp pointer might not be initialized for jumps to the "done" label
in the smp_conn_security function. Furthermore doing the set_bit after
done might "overwrite" a previous value of the flag in case pairing was
already in progress. This patch moves the call to set_bit before the
label so that it is only done for a newly created smp context (as
returned by smp_chan_create).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Due to several devices being unable to handle this procedure reliably
(resulting in forced disconnections before pairing completes) it's
better to remove it altogether.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In the case that the just-works model would be triggered we only want to
confirm remotely initiated pairings (i.e. those triggered by a Security
Request or Pairing Request). This patch adds the necessary check to the
tk_request function to fall back to the JUST_WORKS method in the case of
a locally initiated pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

For remotely initiated just-works pairings we want to show the user a
confirmation dialog for the pairing. However, we can only know which
side was the initiator by tracking which side sends the first Security
Request or Pairing Request PDU. This patch adds a new SMP flag to
indicate whether our side was the initiator for the pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In the case that a local pairing confirmation (JUST_CFM) has been
selected as the method we need to use the user confirm request mgmt
event for it with the confirm_hint set to 1 (to indicate confirmation
without any specific passkey value). Without this (if passkey_notify was
used) the pairing would never proceed. This patch adds the necessary
call to mgmt_user_confirm_request in this scenario.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

It is possible that the HCI_LE_Start_Encryption command fails in an
early stage and triggers a command status event with the failure code.
In such a case we need to properly notify the hci_conn object and
cleanly bring the connection down. This patch adds the missing command
status handler for this HCI command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If a sudden disconnection happens the l2cap_conn pointer may already
have been cleaned up by the time hci_conn_security gets called,
resulting in the following oops if we don't have a proper NULL check:

BUG: unable to handle kernel NULL pointer dereference at 000000c8
IP: [<c132e2ed>] smp_conn_security+0x26/0x151
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU: 1 PID: 673 Comm: memcheck-x86-li Not tainted 3.14.0-rc2+ #437
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task: f0ef0520 ti: f0d6a000 task.ti: f0d6a000
EIP: 0060:[<c132e2ed>] EFLAGS: 00010246 CPU: 1
EIP is at smp_conn_security+0x26/0x151
EAX: f0ec1770 EBX: f0ec1770 ECX: 00000002 EDX: 00000002
ESI: 00000002 EDI: 00000000 EBP: f0d6bdc0 ESP: f0d6bda0
 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 000000c8 CR3: 30f0f000 CR4: 00000690
Stack:
 f4f55000 00000002 f0d6bdcc c1097a2b c1319f40 f0ec1770 00000002 f0d6bdd0
 f0d6bde8 c1312a82 f0d6bdfc c1312a82 c1319f84 00000008 f4d81c20 f0e5fd86
 f0ec1770 f0d6bdfc f0d6be28 c131be3b c131bdc1 f0d25270 c131be3b 00000008
Call Trace:
 [<c1097a2b>] ? __kmalloc+0x118/0x128
 [<c1319f40>] ? mgmt_pending_add+0x49/0x9b
 [<c1312a82>] hci_conn_security+0x4a/0x1dd
 [<c1312a82>] ? hci_conn_security+0x4a/0x1dd
 [<c1319f84>] ? mgmt_pending_add+0x8d/0x9b
 [<c131be3b>] pair_device+0x1e1/0x206
 [<c131bdc1>] ? pair_device+0x167/0x206
 [<c131be3b>] ? pair_device+0x1e1/0x206
 [<c131ed44>] mgmt_control+0x275/0x2d6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Make sure no timer callback is running before releasing the
datastructure which contains it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The LE scan type paramter defines if active scanning or passive scanning
is in use. Track the currently set value so it can be used for decision
making from other pieces in the core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>