MV88E6123 and compatible chips support reading the chip temperature
from PHY register 6:26.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

MV88E6352 supports reading the chip temperature from two PHY registers,
6:26 and 6:27. Report it using the more accurate register 6:27.
Also report temperature limit and alarm.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some switches provide chip temperature data.
Add support for reporting it through the hwmon subsystem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

MV88E6176 is mostly compatible to MV88E6352 and is documented
in the same functional specification. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marvell 88E6352 is mostly compatible to MV88E6123/61/65,
but requires indirect phy access. Also, its configuration
registers are a bit different.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Report known silicon revisions when probing Marvell 88E6131 switches.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Report known silicon revisions when probing Marvell 88E6060 switches.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting skb->protocol to a private protocol type may result in warning
messages such as
	e1000e 0000:00:19.0 em1: checksum_partial proto=dada!

This happens if the L3 protocol is IP or IPv6 and skb->ip_summed is set
to CHECKSUM_PARTIAL. Looking through the code, it appears that changing
skb->protocol for transmitted packets is not necessary and may actually
be harmful. For example, it prevents purposely unmodified (from a DSA
perspective) network drivers from properly setting up their transmit
checksum offload pointers since they inspect skb->protocol to set up the
IPv4 header or IPv6 header pointers. So don't unnecessarily change the
protocol field.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In neigh_parms_release() we loop over all entries to find the entry given in
argument and being able to remove it from the list. By using a double linked
list, we can avoid this loop.

Here are some numbers with 30 000 dummy interfaces configured:

Before the patch:
$ time rmmod dummy
real	2m0.118s
user	0m0.000s
sys	1m50.048s

After the patch:
$ time rmmod dummy
real	1m9.970s
user	0m0.000s
sys	0m47.976s
Suggested-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi_schedule() can be called from any context and has to mask hard
irqs.

Add a variant that can only be called from hard interrupts handlers
or when irqs are already masked.

Many NIC drivers can use it from their hard IRQ handler instead of
generic variant.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Vrabel says:

====================
xen-netback: minor cleanups

Two minor xen-netback cleanups originally from Zoltan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This flag is unnecessary, it came from some old code.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise the interrupt handler still calls napi_complete. Although it
won't schedule NAPI again as either NAPI_STATE_DISABLE or
NAPI_STATE_SCHED is set, it is just unnecessary, and it makes more
sense to do this way.
Signed-off-by: Zoltan Kiss <zoltan.kiss@linaro.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a sysctl that causes an interface's optimistic addresses
to be considered equivalent to other non-deprecated addresses
for source address selection purposes.  Preferred addresses
will still take precedence over optimistic addresses, subject
to other ranking in the source address selection algorithm.

This is useful where different interfaces are connected to
different networks from different ISPs (e.g., a cell network
and a home wifi network).

The current behaviour complies with RFC 3484/6724, and it
makes sense if the host has only one interface, or has
multiple interfaces on the same network (same or cooperating
administrative domain(s), but not in the multiple distinct
networks case.

For example, if a mobile device has an IPv6 address on an LTE
network and then connects to IPv6-enabled wifi, while the wifi
IPv6 address is undergoing DAD, IPv6 connections will try use
the wifi default route with the LTE IPv6 address, and will get
stuck until they time out.

Also, because optimistic nodes can receive frames, issue
an RTM_NEWADDR as soon as DAD starts (with the IFA_F_OPTIMSTIC
flag appropriately set).  A second RTM_NEWADDR is sent if DAD
completes (the address flags have changed), otherwise an
RTM_DELADDR is sent.

Also: add an entry in ip-sysctl.txt for optimistic_dad.
Signed-off-by: Erik Kline <ek@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: support nway_reset

Fix the CHECK from checkpatch.pl and support nway_reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Support the nway_reset() function for ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace tx_underun with tx_underrun for checkpatch.pl.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While testing upcoming Yaogong patch (converting out of order queue
into an RB tree), I hit the max reordering level of linux TCP stack.

Reordering level was limited to 127 for no good reason, and some
network setups [1] can easily reach this limit and get limited
throughput.

Allow a new max limit of 300, and add a sysctl to allow admins to even
allow bigger (or lower) values if needed.

[1] Aggregation of links, per packet load balancing, fabrics not doing
 deep packet inspections, alternative TCP congestion modules...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several warnings and errors of coding style rules corrected.
Compile tested.
Signed-off-by: Roberto Medina <robertoxmed@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch generalizes commit d6a4a104 ("tcp: GSO should be TSQ
friendly") to protocols using skb_set_owner_w()

TCP uses its own destructor (tcp_wfree) and needs a more complex scheme
as explained in commit 6ff50cd5 ("tcp: gso: do not generate out of
order packets")

This allows UDP sockets using UFO to get proper backpressure,
thus avoiding qdisc drops and excessive cpu usage.

Here are performance test results (macvlan on vlan):

- Before
# netperf -t UDP_STREAM ...
Socket  Message  Elapsed      Messages
Size    Size     Time         Okay Errors   Throughput
bytes   bytes    secs            #      #   10^6bits/sec

212992   65507   60.00      144096 1224195    1258.56
212992           60.00          51              0.45

Average:        CPU     %user     %nice   %system   %iowait    %steal     %idle
Average:        all      0.23      0.00     25.26      0.08      0.00     74.43

- After
# netperf -t UDP_STREAM ...
Socket  Message  Elapsed      Messages
Size    Size     Time         Okay Errors   Throughput
bytes   bytes    secs            #      #   10^6bits/sec

212992   65507   60.00      109593      0     957.20
212992           60.00      109593            957.20

Average:        CPU     %user     %nice   %system   %iowait    %steal     %idle
Average:        all      0.18      0.00      8.38      0.02      0.00     91.43

[edumazet] Rewrote patch and changelog.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware can automatically generate pause frames when the number
of free buffers drops under a certain threshold, but in order to do this,
the address of the last free buffer needs to be written to a specific
register for each RX queue.

This has to be done in 'gfar_clean_rx_ring' which is called for each
RX queue. In order not to impact performance, by adding a register write
for each incoming packet, this operation is done only when the PAUSE frame
transmission is enabled.

Whenever the link is readjusted, this capability is turned on or off.
Signed-off-by: Matei Pavaluca <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Local flow control options needed in order to resolve the negotiation
are incorrectly calculated.

Previously 'mii_advertise_flowctrl' was called to determine the local advertising
options, but these were determined based on FLOW_CTRL_RX/TX flags which are
never set through ethtool.
The patch simply translates from ethtool flow options to mii flow options.
Signed-off-by: Pavaluca Matei <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy device supports 802.3x flow control, but the specific flags are not set
in the phy initialisation code. Flow control flags need to be added to the
supported capabilities of the phydev by the driver.

This is needed in order for ethtool to work ('ethtool -A' code checks for these
flags)
Signed-off-by: Pavaluca Matei <matei.pavaluca@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ERROR: "lockdep_ovsl_is_held" [net/openvswitch/vport-gre.ko] undefined!
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
Mellanox ethernet driver update Oct-27-2014

This patchset introduces some small bug fixes, support in get/set of
vlan offload and get/set/capabilities of the link.

First 7 patches by Saeed, add support in setting/getting link speed and getting
cable capabilities.
Next 2 patches also by Saeed, enable the user to turn rx/tx vlan offloading on
and off.
Jenni fixed a bug in error flow during device initalization.
Ido and Jack fixed some code duplication and errors discovered by static checker.
last patch by me is a fix to make ethtool report the actual rings used by
indirection QP.

Patches were applied and tested against commit 61ed53de ("Merge tag 'ntb-3.18'
of git://github.com/jonmason/ntb")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware requires the number of rings in indirection table to be a power
of 2. When setting number of channels to a non power of 2 number,
indirection table is using only the closest power of 2 rings.
Report this number in 'ethtool -x' and not the total number of rx rings.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon failures, destroy_netdev is called, and spinlocks/works must be
initialized before calling it. Otherwise kernel panic may occur.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is instead of calling the actual implementation of
napi_synchronize, for better encapsulation.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

clang flagged the following. All are actually cosmetic cleanups, not really bugs:

drivers/net/ethernet/mellanox/mlx4/en_main.c:233:3: warning: Value stored to 'err' is never read
                err = -ENOMEM;
                ^     ~~~~~~~
drivers/net/ethernet/mellanox/mlx4/en_main.c:293:3: warning: Value stored to 'err' is never read
                err = -ENOMEM;

drivers/net/ethernet/mellanox/mlx4/en_netdev.c:648:16: warning: Assigned value is garbage or undefined
        entry->reg_id = reg_id;
                      ^ ~~~~~~
drivers/net/ethernet/mellanox/mlx4/en_netdev.c:659:2: warning: Function call argument is an uninitialized value
        mlx4_en_uc_steer_release(priv, priv->dev->dev_addr, *qpn, reg_id);
(NOTE: reg_id is only used in the device-managed flow steering path, in which is it always initialized.
 This is not a bug. Cleanup here is therefore cosmetic only).

drivers/net/ethernet/mellanox/mlx4/en_rx.c:122:3: warning: Value stored to 'frag_info' is never read
                frag_info = &priv->frag_info[i];
                ^           ~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move mlx4_en_reset_config to en_netdev.c as it now serves more general purpose.
Add support for turning OFF/ON the rx/tx vlan offlad.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename mlx4_en_timestamp_config to mlx4_en_reset_config and extend it to support
choosing RX vlan offload configuration.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added Support to set speed or advertised link modes via ethtool:
ethtool -s <ifname> [speed <speed>] [advertise <link modes>]
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- If dev cap MLX4_DEV_CAP_FLAG2_ETH_PROT_CTRL is ON, query PTYS register to fill ethtool settings.
else use default values.
- Use autoneg port cap and dev backplane autoneg cap to reprort autoneg interface capbilities.
- Fix typo in mlx4_en_port_state struct field (transciver to transceiver).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added 100M, 20G and 56G ethtool speed reporting support.
Update mlx4_en_test_speed self test with the new speeds.

Defined new link speeds in include/uapi/linux/ethtool.h:
+#define SPEED_20000	20000
+#define SPEED_40000	40000
+#define SPEED_56000	56000
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding ACCESS REG mlx4 command and use it to implement Query method for
PTYS (Port Type and Speed Register).
Query and store eth_prot_ctrl dev cap.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added support for get_module_info/get_module_eeprom ethtool support for cable info reading.

Added new cable types enum in include/uapi/linux/ethtool.h for ethtool use.
+#define ETH_MODULE_SFF_8636            0x3
+#define ETH_MODULE_SFF_8636_LEN        256
+#define ETH_MODULE_SFF_8436            0x4
+#define ETH_MODULE_SFF_8436_LEN        256
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added new MAD_IFC command to read cable module info with attribute id (0xFF60).
Update include/linux/mlx4/device.h with function declaration (mlx4_get_module_info)
and the needed defines/enums for future use.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original motivation for this change was to allow the helper to be used
in files other than actions.c as part of work on an odp select group
action.

It was as pointed out by Thomas Graf that this helper would be best off
living in netlink.h. Furthermore, I think that the generic nature of this
helper means it is best off in netlink.h regardless of if it is used more
than one .c file or not. Thus, I would like it considered independent of
the work on an odp select group action.

Cc: Thomas Graf <tgraf@suug.ch>
Cc: Pravin Shelar <pshelar@nicira.com>
Cc: Andy Zhou <azhou@nicira.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Thomas Graf <tgraf@noironetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not add phy include to the board file but platform_data include
instead.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>